Porsche 911 997 2005 Coolant Water Pump Replacement, How to

Подписаться 1,3 тыс.

Просмотров 15 тыс.

50% 1

Coolant water pump is defective on the Porsche 911 997 2005. The water pump is leaking, it needs a replacement. The bearing and seal failed. Need to remove air filter housing, belt, Loosen the engine support, drain the cooling system, refill the cooling system.
We have monitored the coolant temp with the Bluedriver to make sure it was not overheating.
The previous install they have use RTV sealant and it looks like it clogged the heater core. We will do a coolant flush later hoping it will fix the heating problem. The bolt and housing were full of this RTV Sealant. We have cleaned everything.
DIY repair, how to replace water pump on Porsche 911 997 and 996
PORSCHE
911 Series 1999-2008
Boxster 1997-2008
Cayman 2006-2008
Gates 42579 Water Pump
Canada
amzn.to/3hfFaeq
USA
amzn.to/38TBACo
BlueDriver Bluetooth Pro OBDII Scan Tool for iPhone & Android
Canada
amzn.to/3BTY2HQ
USA
amzn.to/2VtnuV7
Flexible driver I used
bit.ly/3pQqi9s
Thanks for subscribing.
#MassProject #Letsdoit #Porsche
Check out our channel for more stuff with the 1987 Porsche 944 and the Camaro Z28 1981 and more.
Social Media:
Instagram: massproject...
Facebook: / massproject101

Авто/Мото

Опубликовано:

11 янв 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 67

@bhagmeister 2 года назад

Seeing such a young man and his dad like this has brought a very big smile to my face. Cheers

@MassProject 2 года назад

Thanks. Have a look a other video on our channel. They do good work.

@rayladd856 2 года назад

you truly are a skilled mechanic

@MassProject 2 года назад

Thanks so much!!

@ronpatel6640 9 месяцев назад

Amazing job! Too bad you are not closer to me in Ontario

@MassProject 9 месяцев назад

Where about are you?

@miamirice6840 6 месяцев назад

great skills. i like to DIY but think this is a tough one.

@frankdicintio2888 9 месяцев назад

Great video thank you!!!

@MassProject 9 месяцев назад

Thanks!’

@stuartreid6981 2 года назад

Thanks for posting the video - it was very helpful as I replaced the water pump in my 2006 997. It's a very tight space. On to the next project...

@MassProject 2 года назад

Great, make sure to bleed the cooling system properly. Stay tuned for more.

@yannih1782 Год назад

"Lets clean this". And out comes the angle grinder. "No". Brilliant...

@MassProject Год назад

😂🤣forgot about this part

@yannih1782 Год назад

I also have a 2005 997 but its a coupe. I do the odd bit of work on it so when I saw the angle grinder come out I thought you were serious and it scared the shit out of me!

@hobear637 2 года назад

I wish my dad was this cool, great kid and car

@MassProject 2 года назад

Thanks Stay tuned, more coming up

@chuckhei 3 года назад

Great Job! Thanks!

@ryanspeedrunner6017 3 года назад

Well done!! Thanks

@N911GT2 Год назад

Great video. But if you’re going to flush your system you’re better off with distilled water. Also use the Porsche coolant.

@MassProject Год назад

Yes, I do have distilled water for it. Using Zerex G-40 coolant.

@carloshendricks6787 Год назад

Great job on this video; thank you for sharing.

@MassProject Год назад

Thanks for watching!!

@pjay3028 3 года назад

Very helpful video. I now know exactly how to do this........... By taking it to a mechanic and paying him!!!!!

@MassProject 3 года назад

Thanks for watching

@apx36 3 года назад

Belle job!

@MassProject 3 года назад

Thanks Charlie

@carreralicious 2 года назад

Great video! Thanks for posting!

@MassProject 2 года назад

Thanks.

@davidseguin5258 2 месяца назад

Très bon vidéo merci.

@MassProject 2 месяца назад

Merci David

@space_114v2 3 года назад

Good Job ... Nice Video !

@MassProject 3 года назад

Thanks

@ronpatel6640 9 месяцев назад

I am in Oakville, Ontario.

@MassProject 9 месяцев назад

Yes a bit far, 5:30 hours drive

@alanw5812 Год назад

if you loosen the both side rear engine mounting bottom nuts a little, then the mounting plate can move back much easier.

@INTERNA9 3 года назад

WOW!!!!!!!

@jeroenvanboxtel8801 Год назад

Great job! Wouldn’t it be helpful to loosen the two engine mounts up top and lower the engine few cm?

@MassProject Год назад

Maybe but there was enough space doing it this way. Thanks for watching.

@robertjay1179 3 года назад

Man, that looks beyond my scope.

@MassProject 3 года назад

Not that bad, only one step at a time.

@glennbrooks8697 3 года назад

very nice video... well done, especially given how tight some of those spaces were. Curious, what was the total 'actual' time for job?

@MassProject 3 года назад

Without filming would say around 4-5 hours. Had a hard time with the exhaust bolt.

@glennbrooks8697 3 года назад

@@MassProject Thank you sir for the prompt reply!... much appreciated. You are very skilled.

@MassProject 3 года назад

Thank you very much. Make sure to subscribe, we have a lot coming. The engine of the Camaro is out and video will be up soon. 500+ hp

@kianadanny Год назад

What app do you use to monitor in the end? Great job

@MassProject Год назад

Link on thé description BlueDriver Bluetooth Pro OBDII Scan Tool for iPhone & Android

@stevesdiecastcars8908 2 года назад

What exhaust do you have? Sounds really good.

@MassProject 2 года назад

It’s a Tubi exhaust.

@andrewsilverman7954 2 года назад

Well done sir, I was curious what brand water pump did you use?

@MassProject 2 года назад

Gates 42579

@andrewsilverman7954 2 года назад

@@MassProject Thank you sir

@jjforeal2 2 года назад

With my ocd I couldn’t have pulled the pump until I cleaned the engine

@MassProject 2 года назад

that's in the planning to do!! just need to find the time with all the project.

@JoshLoberant 2 года назад

Great video, but wouldn't it be easier if you removed the pipes?

@MassProject 2 года назад

All exhaust bolts were rusted and seized. Didn’t want to break any in the flange.

@JoshLoberant 2 года назад

@@MassProject if removing them was possible, how much easier would the job become?

@MassProject 2 года назад

@@JoshLoberant not much. The only location it was in the way it was for the rear support nuts and we manage with a wrench instead of a socket. The little extra time was less than the time to remove the pipes. Have a look at our latest video. We are removing the engine out of the Camaro Z28 to upgrade the powertrain.

@josephgilliard2129 3 года назад

Can you provide some info on the flexible tool used? What’s the manufacturer?

@MassProject 3 года назад

It’s a Snap-on tool. 1/4 inch flexible screwdriver

@MassProject 3 года назад

Here is the link. shop.snapon.com/product/Flexible-Drivers/1-4%22-Drive-Standard-Handle-Flexible-Driver-(Black)/TM63A

@MrMarquzzo 2 года назад

WHY U DIDNT CHANGE THE THERMOSTAT WHILE U WERE THERE BELOW?

@MassProject 2 года назад

Yes should have done at the same time but didn’t have it at the time of changing the pump. Will do a full coolant flush in spring and will change it.

@bobrose513 2 года назад

The video is excellent. But the music if you could call it that I'd dreadful. I really dont know why people use computer Generated crap. So repetitive..sorry my friend.. it really did spoil the video.. I really don't mean to be rude.. I'd rather it was left out

@K1dPhresh1 Год назад

Turn on captions and mute the video. Problem solved.

@glennbrooks8697 3 года назад

Thanks Mass Project for the like.... what was the actual time on that water pump please? also..would love to see more 997 repair videos.

@MassProject 3 года назад

Without filming would say around 4-5 hours. Had a hard time with the exhaust bolt. We have more coming. There is one about the convertible roof on our channel. Will I have one for door switch replacement. Also one for installing a short shift shifter. And Headlight levelling sensor.

@MassProject 3 года назад

And also full coolant flush.