Mr. Vizard, much respect for your knowledge and experience, Sir. As someone who has always had a fascination with internal combustion engines and high performance, I enjoy your videos.
Thank You David! I have been reading your books and articles for the last 35+years, and your incredibly detailed analysis , combining science with real world practicality made an impression on me early on. You are the real McCoy, and I'm so glad you're still with us !!
Thanks, David. Love your books, of which I have many and the content in your videos. Also, I'm proud to have a cam you designed for me in my 406 SBC in my 240Z.
@@pete540Z I'm building a 260z, it's a road car, that's what I like. I enjoy sport driving on mountain roads. You have to know what your building and stick to the plan.
@@pete540Z I can't afford hybrid z stuff,, lol 😆 I had to go my own way on everything. I think I did alright. I should have vids of the car on the road this summer. You should post some vide if your car.
I have a constant thirst for knowledge so I have always enjoyed your books. I just found your videos yesterday! I would be very interested in your seminars. I think the last air fow seminar I attended was with Harold Bettes.
Thank you David for a very well documented and Professional Video. And while i only recently saw your videos i have seen your books many times but never bought one since i thought they were like the hot rod magazines that are full of paid information that is junk. I will buy every book you have this week and brush aside my 45 year hot rod performance magazine collection. I Paid For A brand new 10.25:1 comp 383 using a new GM block and 4340 Scat Rotating assembly. AFr 195 CNC heads a 750DP street HP carb and Edel... Air Gap RPM The engine was built in Phoenix Arizona by a very well known record holding company "familly owned" and i had it shipped to Australia.. I wouldnt go and had low cylinder pressure .. we pulled the front off it to see what cam was in it and noticed it has a scat 9000 series cast crank and rods that had 3/8 bolts and a hyd roller with one of them stupid spiders to hold the chinese lifters in.. we run a new mechanical cam and new solid flat tappet lifters and got the cylinder pressure up a lot higher and it ran 488hp and 465ft lbs tq and run to 6300 rpm. The 9000 series cast stuff is rated by scat at 500hp max.. i dont feel good about this entry level stuff. With a cam change we picked up cylinder pressure and 68Hp. Good cranks and rods are only a few hundred bucks more than entry level stuff and you can sleep at night.. From Watching these videos from David i will get an engine built in Australia from people who have used Davids mathematics to win, In thinking i was saving money buying from America 12,000 miles away i got Burned. It took me years to save the money for an engine. Thank you David Steve in Australia
Hi David, love the videos, love the your knowledge. I know all the fundamentals are all same but how about doing a little something for us DOHC 4 valve per cylinder guys sometime? Thanks Jon
Thanks alot David. Im kind of an engine geek and love learning not just the how,, but the why.. Still hoping to attend one of your three day classes. Ive read and own several of your books. And for a standard garage tree mechanic I've done pretty well using your recommendations and techniques. I ported a set of 180cc iron heads that you recomended in your cylinder head porting book and with your help, stayed studious, checked my sizes and ended up with excellent flow numbers. My next job is to match your 396 build. Looking for more than 550 out of it. I'd love to give more info and get a cam recommendation for it from you. Thanks again.
Awesome video as always. Thank you. I need to know everything you know on bbc. I recently bought a ss454 that came out of a 90 ish truck. The cam was wiped out and he said it had a rod knock. It's got the oval port heads. I'm building on a budget
I've used that 7/16 bolt Scat rod in a 454 small block that I built. I did some very minor clearance work but not much and it cleared using a 4.125 stroke and a .900 base circle roller cam. They are great.
So theoretical question on the nitrous engine that blew up wouldn't it be true that the engine wasn't actually making 800hp because it was running away from the load on the track and not developing the cylinder pressure that indicated the 800 when it blew up?
Mr. Vizard, what happened to your COS-CAM service? I went on the Terry Walters website, and the link for your COS-CAM service is dead. It has been non-functional for the past 4 months that I've been checking it. I learned of the COS-CAM service from reading your BBC book copywrite date back in 2015.
Sir I appreciate your information. Many years ago when I was a kid I wanted to build a motor for my 68 Camaro , a 4 speed car . So I bought some heads of a retired fellow that had a g gas car that ran really well and built a motor around it . The bottom end was stock chev parts . I carried all of the parts to a fellow in Dallas that built dirt track motors and he built a bottom end that ran in a class that required the use of stock rods ect . He told me he side clearance the rod installed arp bolts and reconditioned them .Attention to the pin also as far a clearance . I spun the motor to 7800 often and never had a problem one . I really like a motor that will stay together and not give trouble . One last thing the fellow I bought the heads from told me he used the longest rod in his motor a 302 and I think it was 6.3 .
Mr. Vizard, Have you ever tried to use pistons 'backwards' and if so do you think its worth some power. I have built some engines with many of your techniques and I use your engine building books religiously.
Thank You Sir for the video and all the other information. This one is very timely as well as I was debating which rods I needed. I will have to go review your books as well now. Thanks Again and have a Very Happy and Healthy New Year.
I am assuming that that scat rod is 5140, instead of 4340. I've had problems with the factory powdered metal rods breaking right at the base of the beam, pulled it apart and the bearing was fine but the big end was still attached to the crank
What kind of RPM, compression, and were the GM PM rods under boost or NOS? Stock rod bolts? As for the latter, I've read that the stock bolts GM pressed into the powdered metal 5.7 rods specifically are very strong, superior to past rod bolts. Is that true in your experience?
I plan on building a Mercedes Stroker engine from 5.0 to 6.0 just like AMG dis back in the 90’s. I will have to get everything custom made except the crankshaft, would choosing Titanium con rods and lightweight piston benefit me in terms of how quickly the engine reaches its maximum rpm? Or would it be a waste of money?
Germans can make the best roller bearings in the world.serving around their shafts in a hard vacuum, spinning at the unthinkable velocity of the translight turbine of the Tesla design.
Thank you for sharing your knowledge with all of us that don't have your experiences your helping us make good decisions with are builds I have a Truck 4 bolt 20/10 tin Nickle Gen 1 small block I'm wanting to build a fast car from stop sing to stop sing no track racing just accelerate to the speed limit as fast as I can so much fun top speed 70 miles an hr
I have a question, if you have time. My car runs a Supercharged MG XPEG engine, I'm sure you are aware that these engines have very long conrods as standard. The conrods I've fitted are custom Saenz with 6mm increase in centre distance with custom JE pistons with a corresponding reduction in compression height. Despite the reduction in compression height they are still a very deep/high piston from gudgeon to crown. The engine is supercharged 10:1 static compression on methanol. It's a period Marshall blower so I can't rev the engine above 7000rpm before the benefit of running it with an excess of methanol is overcome when the air heats up due to the poor adiabatic efficiency of this type of Rootes blower. I do not believe that I have run into detonation problems caused by piston dwell over TDC but have from other causes. I can fit a longer rod without having clearance issues at the bottom of the bore. My question is would you think I would get worthwhile gains by getting even longer rods and shorter pistons manufactured or would I risk the conrods flexing or run into other issues I haven't considered. There isn't much in the way of modern knowledge for these engines despite being used in many late 1930's and 1940's and 50's race cars. Thank you for so generously sharing your knowledge. I have been an avid reader of your books since rebuilding a mini in 1984.
In my thumbnail you can see a Vizard reader and home builder towing a professionally built racing engine in a very fast car off the corner. Some day I am gonna go to at least one seminar.
First off, Love the videos David!! Currently rebuilding my 2008 ram 4.7...Very excited about this build as new for 2008 chrysler reworked the older 2001-2007 287ci engine and took Hp from 235- up to 310hp in 2008, 330 torque, anyway, Engine had 130k, and was time for a rebuild... question is This engine has the 6.12" powder forged "cracked" lightweight conrods that are press fit... All appear straight and not twisted but my machinist said he could recondition them after checking to see if theres any twist or cracks.. Would it be ok to reuse the powder forged conrods for the engines second life? Planning on purchasing my buddies Eaton M112, or building an itb(individual throttle body) velocity stack style build, ported heads,headers, performance tuner, and upgraded fuel pump/regulator, and injectors... any help would be Great!!, thanks for all your experience, and sharing!! Many blessings!!
David lets get a camera and a small lighting system that is worthy of the information you are putting out.... Fire up a patreon and im sure that can get done ina jiffy.....
Hi David, if you want to improve your videos to teach/show us these trick etc could you get a Lapel Mic so your Audio is clear to listen to......thanks
Is there a caged roller bearings bearing pin bearing set inside a cheap Rod's .383 crank main bearings?big end caged cold oil fed through the journals in the crossed drilled and balanced forged crank? Pressure oiled,dry sump vaccume oil pan no windage drag filtered and cooled.i always subscribe. I am anticipating a future contact with Aaron.Aaron Merkami::::: ignition secrets.com.with you.first patent on working Plasma Ignition if you have the courage to examine it like you bravel y confronted the mystery of those fibers action in those magnificent air filters. They sent you a crate of.i thought they were once seen in an episode of startrek ,used in adecoratio not used for their true purpose.