I'm 34 and just got into electronics a year or two ago. I can only imagine how difficult it would have been to learn without channels like this, datasheets, educational resources at your fingertips, circuit simulators to visualize and predict how a circuit works, and not to mention dirt cheap Chinesium parts. I wouldn't imagine you could get a PLL or an op amp for a few cents in 1970.
RU-vid wouldn't let me edit my comment, but I wanted to add that I never would have gotten into electronics if not for channels like Big Clive, Julian Ilett and EEVBlog. I only found this channel recently so it didn't get me started, but it's a great addition to all of my favourite EE channels.
Thanks uncle. I’m a newbie to tube amps and I’ve learned quite a bit in 4 months obsessing. When I get in a rut and can’t absorb any more I always come back to the basics. The xformers and rectifier basics to sharpen up. I miss Rusty as much my Moxie. I’m also a retired pipefitter
Someday I AM going to build my own "Champ" (from there, who knows), and when I'm able to, it will be very largely due to these videos. Thank you, both for the time you and Rusty spend sharing this knowledge, and for the ability to share it so clearly.
Wow, Dear Rusty is shaped like a BARREL. But he is probably the finest Canine-Cameraman I've ever seen. Another great video Uncle Doug - you are educating the world ;-)
Thanks, Stony. I'd like to report that it's all muscle.....but it isn't :) We thought about renting him out as a coffee table, but worried that it might interfere with his career in videography and poodle sniffing (his dual majors in college). Strangely enough, at 16 years old and admittedly rather "portly", he can still jump and chase tennis balls with the best of them......and, as you mentioned, is a maestro with the video camera :)
I don't know what is better... How awesome of a teacher Uncle Doug is, or what an amazing cinematographer Rusty is. Either way, your clear and well explained lectures are inspirational. Thank you!
You're welcome, Jay. Wow!.....High praise indeed, to be compared to Rusty, skill-wise. He is truly a master of his craft :) Either way, we both thank you for your very nice comment and are glad you enjoy our videos.
@@UncleDoug `Just kidding Uncle Doug, I`m trying to repair my rather complex H&K Trilogy amp and your in depth guides are amazing ! Literally the most clear info about tube amps I have ever seen
Great info, thanks Uncle Doug. I must say also that I really appreciate the steady nature of Rusty's front arms for all the camera work. Thanks also to Rusty.
+Viking Mike You're welcome, Mike. Rusty studied at the UCLA School of Video Making, majoring in tennis ball with a minor in dog cookies. Steady camera holding was his favorite class :)
Dear Uncle Doug, Rusty sure is a beautful dog. I personal restore tube radios for my own enjoyment, and I have decided to watch all of your videos, I enjoy the way you present the material, it is easy to understand and very informive. Thank you kindly for presenting these videos. Have a great weekend...
So size does matter. I always suspected my exes were just being kind. Superbly explained, sir, and great camera work from the much missed Rusty. Many thanks.
@@UncleDoug The thanks are all mine. When I was a kid I'd turn the radio to the wall so that I could watch those beautiful glowing things and wonder at the ingenious magic that was in there. 60 years later and it's still magic. But underlying it all is logic. And I'm starting to get an understanding of all those itty bits. A priceless series of videos which have edutained me while locked down on my boat in the middle of England. Keep well.
Can't say how much i appreciate you posting these videos... Found your tube amplifier videos, and I now have a very good general knowledge of everything you have covered. Excellent job, and many thanks for sharing your knowledge with the world.
I have an old Marvel 35 [Valco, maybe?] combo which is essentially a clone of a 5c1 champ [octal 6S*7 preamp rather than 12ax7], and your channel has played an integral part in my identification of the circuit and current repair/restoration thereof. I really appreciate your thoroughness to the smallest of details; I don't even bother to seek out other users' videos of this nature anymore..
Wow, thanks, Scott. It's great to hear that the videos are actually providing useful information.....and that viewers are actually applying the principles to their own projects. I hope that Rusty and I can continue to provide useful information :)
Dude, you are a wealth of practical information and electronic ejamukashun. Love the simple, straightforward delivery and explanation. I'm learning a ton and you're clarifying stuff I was a fuzzy on. Thanks. Again.
No; thank you. Good, clear information is hard to come by. Too many self-styled experts can't easily explain that 2 + 2 = 4. I, and I'm sure many others, have no problem grasping the principles you present. It's refreshing and welcome.
I enjoy coming back and watching these tutorials on the basics that you make from time to time,UD. Just to make sure I’m not suffering from the Dunning Kruger effect if nothing else. There’s no WAY the Diane Kruger effect could happen to ME! ;-)
great intro to power transformers. I have some old tube radios and one of them, a 1948 RCA, has a smoking transformer, so I'm watching a lot of videos about transformers and yours was extremely helpful.
Great Video!The thing that would help in understanding is take an amplifier and follow the schematic and put together the amp hands on as you put it together and explain it. You have the best videos on youtube.
I am a Certified Electronics Technician (Audio Specialist), a confirmed audiophile, and a lifelong member of the "Fraternal Brotherhood of Goldenears" (such an organization does not officially exist :), but it should!) And I LOVE tubes! Ah! How did I end up subscribing to a channel dedicated to GUITAR amps!!! :)
Hi Doug, I checked the Filter Caps with the Anatek Blue ESR meter, after calibrating to 0.00. 32uF 1.9; 22uF 1.3, 22uF 1.4, 200uF 0.31, 200uF 0.31; Grid Bias Cap 330uF 0.31 All test fine @ 450V Thanks for your time Doug, please say hello to Jack & Casey for me.
Hi Uncle Doug, I have used a Classic Tone Transformer like this one and IIRC when you connect it to the 120V line AC the white wire is connected to the white and the black/white wires on the primary side.( marked 1 & 3 on the spec sheet) The black wire from the AC line is connected to the black and the black/white wires of the primary side. ( marked 2 & 4 on the spec sheet) Basically when using the transformer for 120 volt operation, the primary windings are wired in parallel. When using it for 240 volt operation the primary windings are in series. Either way you need to use the complete primary winding for the transformer to function correctly. Keep up the great work and pet Rusty for me.
Hi Uncle Doug, I've watched your biasing videos today as well and they're all fantastic. Great, clear explanations and delivered really well. I've commented on this one because Rusty deserves it!
INFO IS GREAT I WATCH YOUR VIDEOS WHEN IM CLEANING MY HOUSE (WHOOP CAPS) I live in a 100 square foot place big yard for my pit bulls who have a tiny house with ac and a heater also then i have my little side kick and two cats that live in my house, then in the main house which is my folks ( i help them out with what they need, they let me live in my tiny house on their land and gave me half the yard for my dogs) they have 4 dogs in there house which were all from when i was rescuing dogs at my bigger place. anyways im a total dog and cat lover and full time musician who pays the bills selling gear. even though i feel my stuff is pretty good and guys from Warren Haynes to Craig Bartock use it but i always love learning and relearning and your videos keep me watching.
i just finished a red headed step child. i had a hoffman deluxe with vibrato from black face era amps it was missing an out put. i also had an early break up weber output laying here for el34 tubes and a 4x12 cab which was built by a shop to resemble a 40s record player cab. its got slotted wood baffle. last i set of jensen mods. I cut the 2x12 down and mad a back bottom mounted 2x12 combo. So i threw it all together which makes it an early break-up el34 tweed deluxe with the tone pulled and turned into a bass cut. going through 2 12 inch jensen 25 watt MOD speakers loaded in the cool cab. it actually mad a great middle volume amp. I go for tube saturation. although i sell pedals for a living ( and a little ghost building/designing) i only run a range master style boost to push my full volume amps harder. I have 4 amps all of different volumes so whether im at home or a gig i can play my amp full volume. anyways i have watched your videos a ton to get a handle on some of the things i had to change to make this basterd amp work. and also my silver face champ turned into a little monster with volume body treble mid bass controls killer little amps all choked up and everything thanks to your videos.
Really helpful video to determine which trafo to use. i dismantled a champ 12 totally and want to rebuild it without the PCB boards and without the reverb and switching unit for clean/dirty, so just 1 channel. thx Uncle Doug.
I am thinking about building a tube amp and your videos are worth their weight in gold. The concepts have been explained in such detail it is unreal. Much appreciated. I have done a bit of electronics in A level Physics, but doing more research into how things work together as I am fully aware of the very high voltages present and your videos are an excellent guide. Thank you.
Thanks again Doug for another great video. Power transformers are probably the most overlooked part of an an amp. It seems these days it's all about the tube used. I want to relate a situation I had many years ago with a Sunn Solarus amp I owned for several years in which the power transformer died. After confirming this, I ordered a new one directly from Fender/Sunn($37.00) and installed it without any problem as I had recently finished my schooling in electronics. The amp turned on ok and appeared to be operating ok except someone noted there was some distrotion when there shouldn't be at that volume level. I didn't think much of it at the time as I was still quite new to all this , however now I have reason to believe there was also another problem present that I failed to look for thus, did not detect. I wish I could get my hands on this amp again even after so many years...since 1978 and find out what was wrong, if the amp even still exists, as it was traded in for another Sunn at a local music Store in Traverse City, Mi. Sure wish I could find it again. It was a great amp.
John Zook You're welcome, John. Thanks for sharing this story with us. I think we have all sold items.....and then come to regret it later. My list would take several hours to type out :)
this is what we call in the UK An "old school" electrical installations lecturer, he covers everything you need to know and just that, no fluff. and no rubbish. Usually guys like this have a long history of "Trusted Person" roles in the large scale Electrical installations industry. And a dodgy knee or something from the one time they had an accident which was not their fault involving high tension Electrical systems, by trusting someone they should not have trusted to lock off the supply properly, or something similar. From that point on they develop a need to pass on quality knowledge and a healthy distrust of less qualified/experienced people.
Wow......quite an analysis, MB. I do indeed have 2 bum knees, mostly from kickstarting old British motorcycles....and an occasional wreck or two, after they started ;)
Hi Doug! Another excellent video! I've had several ordeals with new, off-brand replacement transformers. many of the replacement PT's I've used in the past were problematic, and unreliable...I've had many that had shown exceeding specifications (on paper) but in the real world, didn't deliver the goods (necessary current) I try to stay with only a few suppliers (Triode Electronics being one of them as per your recommendation) Tube Depot, and AES) so I know that the proper replacement will be delivered to me...Ah, I miss the days of Thordason and Stancor transformers...they were made to last...Mercury transformers so far, have been reliable...(keeping fingers crossed). I'm still in amazement how fast Rusty is at grabbing the ball in mid air :) Keep the videos coming, always great to watch :)
Thanks, Frank. Rusty appreciates your kind appraisal of his athletic prowess, which is pretty impressive for a 15-year-old dog ^. .^ I agree about Thordarson transformers. Way back in my jukebox days, they were the best !!!
Hi Doug, Hope you are well. The Studio City 50R's problem where the current limiter bulb was glowing brightly when turning on just the Mains switch was diagnosed to be a bad diode in the full wave rectifier. So I replaced them all. I biased the EL-34s @ 17W PD. The hum is still there but fairly tolerable. Before the diodes arrived, I checked the power transformer and it checked out great, no problems. I went through all of the component values and they also checked out as being in spec. One solder connection on one filter cap was loose to my surprise and I took care of that in short order. I did reduce the hum to 0, but that occurs when either the Plate voltage was high and current too low for correct PD, also the opposite where the Plate current and PD was very high. As I also found out, and it makes sense, is that even though the Eurotubes "Pro One" Bias Probe enables us to easily bias one of the EL34s, when you change one tube bias, it will affect the other. So there still is some trial and error to bias them both to similar PD. Thanks again for all the great instructional videos! TG (Tom)
Another fine explanatory video, done as Einstein prescribed: as simple as possible, but not simpler :) If only Rusty didn't snatch those written comments from the screen so quickly... They disappear so fast, that paying attention to what's shown *and* reading them when there's a good moment is impossible, I have to pause the video. Of course, it may be due to my poor reflexes :-D
Thank you for the kind words and very flattering comparison, Stan. I understand your plight. I'm the same way with closed captions on DVD's......having to pause the disc continually so my wife and I can read them, before we move on....to the next caption. It takes us about 3 hours to watch a 2-hour movie :)
Whew! That was scary. I stayed tune to see the Rusty outtakes and for some reason I "thought" you were going to play "tennis ball" using that gigantic transformer! Thank God cooler heads prevail. Oh, and while I'm at it, this lesson was superb. I will watch it, and others, several times. I take it that you and Rusty must have been teachers at some point because I can't imagine better electronic lessons. I have a hard time learning new things like this, but I am having no trouble following along. Lately, I have been refurbishing my old Fender amps and it's going quite nicely. Next project? Building an amplifier from either a kit or from scratch. Thanks so much for all you do.
Bourne Accident You're welcome, BA, and thanks for the very kind words. Rusty was a tenured professor at an obedience school....and I taught math and science for 16 years, so your guess was correct :) Rusty was probably up to retrieving the transformer, but the prospect of throwing it didn't appeal to me, so we settled on the traditional tennis ball. We're glad you enjoy the videos. By all means, follow through on your desire to build an amp. If you're careful....and it works well....it's a very rewarding experience :)
i am so glad you are our teacher on amps. do you have a video on the tech instruments we need to check or build audio tube amps ? next would be , Do i need a math degree to figure out to build an audio amp? do you have a video on just how to read all the specs on a tube sheet and break it down into understandable jargon?
Thanks, RC. I have no video dedicated to the necessary instruments, but they are generally evident in the repair videos. A good meter to test resistance, voltage, current, and capacitance is a necessity to get started. No, you don't need a math degree, only a strong desire to study and learn. I have not yet produced a video on interpretation of tube data, but it would be an interesting topic. You don't really need to fully understand a tube manual to build an amp. I think the best way to start out building amps is to buy a kit for a simple chassis, like the Fender Champ, and build it. As you do, try to understand the function of each of the components (using the Internet as a resource). After that, you might try building your own amp by downloading a schematic, selecting and buying the necessary components, and assembling it without instructions other than a schematic itself. Good luck.
Hi Uncle Doug. First off, thanks so much for taking all the time and effort to make your videos. I wish I had professors in school who were as concise, clear and easy to understand as you. Secondly, I have an old (1968) clone of a Traynor YBA-1 Bass Master (and by extension, patterned after the 5F6A Bassman). It's a Lifco Model 1000. Information on the net is extremely hard to find when it comes to details. I'm trying to figure out if it'd be possible to do a few mods on the amp since it didn't cost me much and likely doesn't have much residual value left. It's currently running a pair of 7027A's in the power section, and three 12ax7's in the preamp. There is a spot for another preamp tube, unused. I was thinking of adding another 12ax7 and converting the power tube sockets to run EL34s like a JTM45, however I cannot find any identifying marks on the transformers, nor can I find any information about Lifco transformers online. Is there any way I can figure out or calculate the ratings on the power and output transformers without knowing anything about them?
+ConvoysToNothingness You're welcome CtN, and thanks for the kind words. Unless there is a part number on the transformers that can be traced to a data sheet, there is no way to know for sure. About the best you can do is make an educated guess based on the current requirements they fulfill in the amp circuit they came with. In addition, most amp builders use transformers that offer some leeway above the circuit requirements, so it's generally possible to add a fairly-low-current-drawing pre-amp tube to an existing circuit.
Great video! Very useful stuff to know for future (hopefully) tube projects. For couple of months now I'm surfing thru websites like ebay and our polish equivalents of those auction sites to get some cheap elements or devices to salvage parts. Mostly solid state because I'm rather new to electronics. But now when I got "something" for tubes and finally understands basic of them I'm also looking for some cheap tubes like NOS etc. And now ALSO gonna try to get old transformers cause they seem so simple now! :D Anyway, to not bore you too much I'm glad that I found your channel. Thank you very much!:)
It is better to have more current capability than not enough. Current is "as needed" and you have more problems (many actually!) with too little current available. Also, mechanically, a transformer is not affected by its orientation to the "floor". Mounting it sideways, so to speak, gives more "headroom". (The physical type). ;-) Do I have this correct, Rusty? Uncle Doug, please let me know what he "says". :-) I am learning so much from you two. Thank You!
I awakened Rusty from his (fifth) nap of the day, and he responds: "Yes, indeed, JL, it's always better if your PT can exceed the predicted current draws by a safe margin, say 25%....otherwise it will run hot and possibly go up in a cloud of (expensive) smoke. Regarding the orientation of the PT, we tone (and nap) purists always prefer the horizontal orientation whenever possible.....zzzzzzzzzzz"
Thanks, BT. Rusty's camera work was indeed superb for this video, and it's good to hear that my hand-acting classes (with Stella Adler) are finally paying off....:))
Thanks, Dave. I think the best way to protect a Power Transformer (PT) is to have it properly fused, i.e. with the lowest-possible-amperage fuse that will still allow the amp function. The fuse value may even be lower than what the factory recommends, since they were more interested in "fire" protection than the protection of a (now priceless) vintage transformer. I am not a big fan of slow-blow fuses. People don't realize that a slow-blow fuse can tolerate twice its rated amperage for over 10 seconds before opening the circuit......by then, the PT is most likely fried. Any internal shorts (i.e. shorted filter caps) or running the amp with output tubes biased way too hot (excessive plate current) are probably the leading culprits in PT damage. You can tell if the PT is overheating simply by placing your hand on it after 10 or 20 minutes of use. It should be warm to the touch but never uncomfortably hot.
Thanks so much for these videos Uncle Doug, I learn more and more from each one. This information is not explained in such a digestible form anywhere else that I have found. A lot of effort have clearly gone into creating them so if you have some sort of paypal donation set up I would be more than will to contribute. How is Rusty going? I hope he is still well and happy. All the best and thanks again!!!!
You're welcome, Adam. If you'd really like to show your support, you can make a one-time donation to our PayPal account, dldcam@aol.com, or become a patron on Patron. Thanks so much :)
Excellent work my friend! Very informative and highly educational! I must say that I have waited for this since your last instalment and feel very confident that my skills are growing further with your videos- thanks uncle Doug!! Great as always! Can I request another idea for a video? "I (and I'm sure others) would like to know why the pots in guitar amps are rated for different values & how these values are chosen to meet the requirements of the circuit". Also- the tone stack shaping caps and how they effect the first couplings in the tube preamps... Just a thought ! Thanks again. Great days!!
Thanks so much, TBM. I'm pleased to hear that the videos have been informative. I will take your suggestions to heart and will try to come up with an explanation for the pot values and tone capacitor effects.
Thanks, Alva. Yes, that transformer is from a Baldwin organ amplifier that used about a dozen tubes, so it's windings have substantial current capability. I'd love to use it to build an amp, but would probably need a fork lift to move the amp around.
Uncle Doug I wonder what the HT voltage rating on it would be. It might make for a good tube bass amp. I've played around with the idea of building a tube bass amp, but it would be quite expensive and hard to find the right transformers for it. I've read that a pair of KT120 tubes can get you as much as 150 watts in push pull, so my idea is to use a quad of KT120's, so you could get a 300 watt bass amp like those old SVT Ampegs.
It drove a pair of 6L6's, so the B+ would probably be around 450 to 475 VDC. I also have the filter choke and output transformer from the amp (both are quite stout). It is definitely tempting to build an amp around them......but they are so darned heavy. I can't imagine the PT that could handle a quartet of KT120's, or the cooling system you would need to dissipate 240W of Plate Dissipation. Wow !!
Uncle Doug If I ever get around to building such an amp, I will probably just use a pair of KT120's. They're tempting to use for a tube bass amp, because you'd get a tone of clean headroom, and I've heard very good things about their clear bass response from those who use them in HiFi applications. But man oh man, I know the transformers alone are going to cost a fortune.
They are definitely "current hogs" and thus would require a big, expensive PT. I wonder about the possibility of using two, smaller PT's in parallel, each one individually rectified. You might get the current, but It would probably cost about the same, and you still would not get the outrageous plate voltage that these tubes need.
Hi Uncle Doug, Hope you are well. Well, I was finishing up the restoration of the Studio City 50R, 50W amp head, and replaced those out-of-spec components; filter caps, plate resistors, etc., and had set the PD of the 2 EL-34s several times. First, to about 70% of the max 25W, then and lastly to ~19-20W to achieve more head room. During the intermittent testing after the installation of new components, tubes included, I noticed a low to mid level amount of hum from the (4) 12" speaker in my Marshall Cab. (Impedance of the cab 16 ohms Mono as was the amp set at 16 Ohms) In the course of audio testing without the current limiter (for the first time since all other testing showed no excessive amount of current being drawn, Please note however, previously, the bulb filament was glowing a faint orange. I considered this to be normal since the amp is 50W. I recall a similar situation in one of your videos). I chose a different outlet in a different room to see if perhaps there was some "ground loop" causing the hum. Perhaps this level of hum was acceptable, IDK. Shortly after, I turned the amp on again and the 3A Mains fuse blew. Took the amp back to the bench and after installing a new fuse, turn the Mains switch on and was blinded by the current limiter 300W bulb! Whoa! I immediately shut the amp off and am diagnosing the problem. I'm just looking for some feedback during this process. Maybe you may have an idea why this could happen. After looking at the primary and secondary sides of the Power Transformer, I measured some resistances. Q1: Are the resistance values I measure valid without disconnecting those leads from the amp? One resistance I measured was the resistance across the Hot and Neutral leads of the power cord so as to measure the resistance of the primary winding. I got 5.7 Ohms, seems low to me. Q2: The Secondary Filament leads seem to have continuity to chassis ground at 0.2 Ohms And with respect to each other from the winding to be `0.2 Ohms! Same resistance , that is , practically no resistance. This seems Very wrong! As a note about being careful during component replacement, I was very careful to take pictures and draw diagrams beforehand, so I could refer to them. Also, I never got too far ahead of myself during replacing so as not to make a mistake during replacement. Any thoughts are appreciated! Thanks Uncle Doug
I wonder if one of the new filter caps failed, causing the initial hum and then, possibly due to an internal short within the cap, the final dead-short indication from the CL ???
Uncle Doug Thanks Doug, i will check them out. If you are correct, and 1 of them had shorted, would that be detrimental to the power transformer? See, the current limiter lights up when only the Mains switch is turned on and the amp is only in Stand By mode. I think the FCs are only energized when the Stand By switch is closed to permit current to energize the FCs and remainder of the circuitry. Initially, since the hum wasn’t responsive to volume, i thought 60Hz hum, and realized the filament circuit wiring lays on the tube side of the chassis (wierd), holes are drilled through the chassis on either side of the tube socket to allow attachment to the sockets. Not very efficient as the twisted configuration i see in the Fender and other amps you’ve worked on. So i moved around the 12AX7s and then bought a matched Quad of Tung-Sols. I’m sad because i was just getting ready to test it with my Scope and Tone Generator. ::( Even my dog Spunky is melancholy! Maybe i let him give out candy to the treat or treaters tonight to cheer him up.
@@tangotommi As I have noted many times, TG, it is virtually impossible to troubleshoot long distance, without the ability to observe and test. If the short only appeared after your repair work, then the cause must relate to the work done. I would focus on every solder joint, component value, and connection made during the repairs.
@@UncleDoug I understand completely. It really wasn't working well when I got into it. Terrible sound, dirty pots, some wiring incorrect for biasing properly, Reverb driver 12AT7 in the wrong socket. Then I made it sing for a while. Cest la vie. That's ok. It's a tough one for my baptism/initiation into Ampaholics Unanimous.
@@UncleDoug I just wanted to thank you for Not suggesting anything more. You're an excellent instructor. It's the best way for Anyone to learn is by Doing. I just turned 68, and in retirement, this a perfect hobby to keep my mind sharp by problem solving. Yes, even though I Feel confident on what I've been able to accomplish on this amp, and don't see the error I've made, it doesn't mean it's not there. I Will find it and I will be the first to admit any oversight on my part. I'll keep you in the loop when I find the problem since you may find my predicament pertinent to bring to the attention of my fellow subscribers. Thanks for all the projects and subject matter you convey to us! I remember upgrading a Hickok 539C with a kit supplied by Bill Eccher, a retired electronics expert from the Navy. I asked him if he could recommend something for me to learn about vacuum tube technology and he sent over the Navy training manual. I got swamped in the first 30 pages. That was about 5-6 years ago. However with the videos you've published, I've learned So much more practical knowledge to help me understand electronics of vacuum tubes and amp circuitry. Thanks again! Keep 'em coming!
Hi Uncle Doug!!... Absolutely love your videos...I wish I had teachers, while getting my BSEE & MSEE, who explained the technical issues as clearly and precise as you do...I'd like to ask, which video(s) you recommend that clearly explain the power amp operation, from the point after the phase splitter, as clearly as you have with the preamp...It obviously doesn't matter how many degrees a person has, it's the experience and hands-on that truly develop your technical know-how...school is great to get a solid base of technical knowledge. I would just love a better understanding of the power amp section, as a whole...Thanks again for your time taken to share your solid understanding of amps. Rusty has a very steady paw while filming....and I love Jack's occasional walk thru during filming, it's just like the ring ladies showing which round it is in between rounds!!
Wow, high praise indeed, Craig. Thanks so much. Have you watched the output transformer video ? As I recall, it goes into some detail regarding how the two out-of-phase signals from the phase inverter drive the output tubes, producing greatly amplified high-impedance (voltage) signals that are united in the output transformer and converted to a low impedance, high current signal to drive the speaker.
Hi Uncle Doug; Could you please explain why the current of the output filaments is never included in calculating B+ lines when it must be considered when calculating step-down voltages? Thanks for regularly checking recent comments re: old postings. 👍👍👍
@@stephenrioux6821 I believe that in any plotting procedure based on plate current vs plate voltage, the plate current value should not include screen current. The combination of plate and screen current is normally referred to as cathode current.
Smokinone951, your question did not have a Reply capability. It sound to me like the On/Off switch is faulty. Next time it delays coming on, wiggle the toggle switch and see if that helps. If it does, you need to replace it.
Howdy. Nice presentation. One thing however. If you measure the AC current before the rectifier with a r.m.s.value meter you will find it to be larger than the sum DC anode currents measured with a mean value meter. Rating the transformer's power the AC r.m.s. value should be used. This could explain why we have transformer burn-outs occaisonally. If the anode current is filtered with a large choke the AC-DC difference is smaller. But if the filtering is done with large el. cap.s the difference could be really large. The AC r.m.s could be 1,5 times the DC mean.
@@UncleDoug I am happy to provide input. And by the way. Some time ago we discussed the magnetization effects in output transformers to the signal fidelity. I presented the issue to EDCOR engineers. They pretty much agreed that the magnetization has little effect and practically no relevance to the output signal. Assuming, of course, that magnetization is not driven into saturaton.
As always, great video UD. You always have a barrel full of practical info in these videos. Have you ever considered a deeper dive? I would like to suggest explaining whats going on in the magnetic core of the transformer, but am reluctant to ask.....(pun intended). Did you ever teach Maxwell's equations? My guess is that you did - at least the amperes law portion. I would love to hear you cover Maxwell as you just have a way with your explanations and analogies that really makes sense to me and evidently many others here. I can understand you have better things to do, but maybe Jack can handle it if he's not too pissed at the Physics crowd over the whole Schrodinger's cat thing. Thanks again.
7:11 Well the other day my lucky streak caught up with me. As most of these stories begin, I had just finished my first amp build when curiosity got the best of me. Flipped it on and after about 20 seconds my rectifier is red plating like crazy. Apparently the pilot light was shorting to ground and it burned a nice short between the 5V heater and 6.3V heater windings on a new Mercury Magnetics power transformer... Use a current limiter! haha good times
In the future will you discuss the wax in tranformers. one of my transformers in my micromatic has a little bit leaking out, i don't kow if that means it's toast, or can i just rewax it somehow( i assume the wax is an insulating substance) it runs fine but the wax worrys me a little. Great video. it was nice to hear rustys neigborhood fans cheering him on.
Greetings, Franky. Leaking wax would imply that the transformer (TF) has been overheating. You might want to check into why this is happening. You can place your hand on it while it is in use. It may be warm to the touch, but should not be real hot. To my knowledge, there is no way to "rewax" a TF. If the overheating continues, the TF will probably fail, producing a unique odor that, once smelled, can never be forgotten :) Rusty's loyal fans always cheer when he is playing ball, much like when Babe Ruth came to bat in the good old days.....hit or miss, it's always a good show. Thanks again for your comments.
When you were looking at the transformer from Triode you mention in the annotation that it is not the correct mounting style. Could you explain why that is so? What is the difference between mounting horizontally vs. vertically - other than the practical consideration of how your chassis is routed?
In horizontal mounting, there is a large square hole in the chassis that accommodates a portion of the transformer body. This is the type of mounting that is generally used in chassis that hang from the rear roof of the cabinet, like a Fender Champ. The vertical-mounted transformer is more commonly found in chassis that rest upon the floor of the cabinet with the transformer pointing upward.
Uncle Doug I believe I forgot to specify that this 68' custom vibrolux reverb is the new one the fender "reissue" in 2014 (but the schematics is far far away different from the original 68'). It has no rectifier tube and the transformer (165v-165v no center tap) have not the secondary 5 v. So I imagine that to install a socket for the 5U4 I have to drill a new hole and I also need a PT with three secondaries. So I'm a bit confused about how much the current would be in the end. Could you clarify me, please? Thank you for the videos and the attention!
My advice would be to sell the amp and buy one that better suits your needs. Changing power transformers, adding tube sockets, altering circuits, etc. would represent a whole lot of work and expense to gain a little "sag", and, to be honest, I think you would be disappointed by the result. You would need a PT with a center-tapped HV winding, probably around 325-0-325, and a 5V 3A filament winding. If you watch my videos on the Supro Tremo-Verb, I explain the selection of a PT and the high voltage DC you can expect. If you still choose to proceed, good luck.
Greetings, Ben. You are correct. I have no experience with export transformers, and didn't read the "fine print" (in parentheses :)) I will add a note to the video to make this clear. Thanks !!!
Hello UNC. Jeff OD here in Jersey. Gave up on the Chinese amp circuits. Q: I'm building the RobRob blackface AB763. Can I use a 290BEX Hammond Power Trans? Getting 1/2 voltages on 6.3 and 5 VAC windings. Be well Uncle Doug, and keep up the great work.
Greetings, Jeff. Without tech data I can't tell if the transformer will work. The "half voltage" comment is puzzling. Were you measuring between each 6.3V lead and the center tap? Since the 5V winding has no CT, I'm at a loss to explain it.
Uncle Doug, Do you think that an "upgrade" transformer to replace a functioning stock transformer will improve the tone? According to Mercury Magnetics, who make transformers for that purpose: " They're integral to the nuances of your guitar amp's sound. Far more than tubes, speakers or other amp components, the transformers establish the platform for shaping your amp's unique sound." If this is really true, what sort of secret sauce do they impart to the current that a stock transformer, in say, a Fender amp, doesn't? I enjoy your videos. You are such a great teacher!
Thanks so much, Bill, we really appreciate your nice comments. Re boutique transformers, listening to a sales pitch like this is akin to asking a barber if you need a haircut.....you know darn well they will say anything to get you buy their product/service. "Establish the platform for shaping your amp's unique sound"......give me a break. MM has a great reputation, but I find their prices to be way out of line with any real benefits associated with their products. In my experience, and directly contrary to their sales pitch, tubes and especially speakers have far more genuine, noticeable effect on tone than any other component, including transformers......even real fancy, expensive ones :)
Thanks, Brian. Due to the amount of correspondence we receive daily, we are unable to engage in such private discourse, but will try to answer basic questions via this format.
Dear Uncle Doug of Danisonic. This is another fine vidio on Eletronics thanks. The duel 120v inputs in series to operate at 240v is corect but I Think they should be put in parallel for operation at 120v It will make the primary cirquit work better and efficiently. Otherwise the secondary voltage through the rectifier And other cirquits May sag to much. What do you think? The rectifier
You're welcome, Zep. Each of the voltage outputs has its own winding ratio, i.e. the 6VAC filament winding would be about 20:1 with 120VAC primary input. To produce 660VAC from 120VAC input, the high voltage winding ratio would be about 1:5.5 by my calculations.
Hi Doug! Excellent video. I’m working on a WEM Copicat tape echo machine, tube powered, and I’m only getting 1.7V on the secondary that feeds the diode rectifier. It should be 250V. Does that sound like a faulty transformer or is the circuit simply not pulling enough power? Maybe bad smoothing caps?
Does the secondary output remain 1.7V when you disconnect the diode rectifier? If so.....bad PT. If it goes up to 250V, then look to the rectification stage for the problem.
Uncle Doug, I don't know if you will see this but I am having trouble with replacing a transformer. It's not a tube amp, it's a Soviet synthesizer that has a transformer that takes 220v in (at less than 0.125A apparently) and puts out two sets of 10v from two separate windings. Do I need to find a transformer that matches that design (separate windings for the same voltage) or can I just use a transformer with one set of wires, solder it to a board, and basically use one transformer for both sets of voltage? I have the PSU board schematic.
