Proboat Sonicwake 8s ZTW SEAL 300A Leopard 4082 1600kv🎅 

Hi..yes it's good it clears the rudder also I cut the rudder bracket and rescrewed it back on again I hope you can see that . That's good you can't wait..😊👍🌞🌈🌞🌈

I had to see it again

Haha.. definitely not👍..yes abit much pink and red colours going on😄🙋..I'm just bored outa my brain theres so much rain today I can't go to work😕

Speed Freak my wife would kill me . lol

Me also Emil..not sure how it will be it now weights alot so hopefully it will work for it at higher speed🤔

Hi..bolt your 4082 motor onto the stock black plastic mount with the motor cable connector fitted and then try lay it flat ,it will not fit flat until you dremmel the rear motor mount,the round plastic seat has to be ground down to fit the rear of the motor..you'll need to be perfect or over grind it by .05mm,The motor mount has to be perfectly flat when you bolt it down other wise you will get the wrong angle and chew out your brass tube teflon liner and get lots of heat

Yes 100% change to Seaking 180 ESC and add an extra water cooling pickup ..

@@paulcooper7162 thx cause I noticed with the stock esc the motor doesn’t get full power

@@ntxmxraw6648 I didn't know that..im using flycolor 150A ESC now,I use a capbank from Swordfish 300A ESC from Offshoreelectrics.I found the esc is half the price of Seaking 180A and I've torchure tested the 150A ESC and excellent

@@paulcooper7162 Do you think the esc is my problem?? Or something else

@@ntxmxraw6648 I really don't know..my friend has a stock Sonicwake and it handled terrible so he gave it to me and I fitted a new flex cable 4.76mm from AliExpress as the stock one slipped ..I changed the prop to a 42mm 1.4p CNC from AliExpress Tilkiea store and bent the trim tabs down a bit and his boat is fast pickup and temps are all good.and the handling is decent no probs from the stock ESC ...the Sonicwake flex cable slips

Hi😊..I didn't GPS it but it was really powerful and ultra quick acceleration..my advice as I've already done it fit the leopard hobby 4082 1600kv ,all the 3674 motors are too small,I do have another 2 vids showing the leopard 4082 it didn't get hot like the 3674 motors

#PaulCooper - Are you referring to the - Leopard 4082 4-Pole Brushless Motor 1600kv?

Hi the Panther Graphenes are excellent as they deliver more power without the heat that other lipos get..every time I use them I get a surprise 😊🚤💨

yes haha I did have to mount the lipos on top...to be honest the boat handled better and had more power than the vid I have of the Sonicwake with 180A Seaking leopard 4082 1600kv 6s..the 8s setup was too heavy .I delete lots of vids, some one gives me thumbs down almost immediately after I put a vid up it's not nice. The esc that perform s better than a Seaking 180A is a stock flycolor 150A with Swordfish 300A ESC cap banks fitted..I'm running 6s on that in my Vector and it's amazing

@@paulcooper7162 i had a flycolor 150 in this pursuit for about a year .then it burned up . so i figure i try a seaking 180 since people love them so much . i actually had my best top speed running the flycolor 150 . i have not broke 60 yet with the seaking 180 .with flycolor my best was 63 same setup .it could be cold lipo syndrome. my top speed runs were in the warmer months . that zeal 300 must have set you back quite a bit . i think the 200 would have been enough for you . you run 8s yet?

@@fnkycoldmedina Hey yes must be the lipo temp.. I'm going to use 150A flycolor s on my Zonda and try get a decent top speed,I got panther lipo s and some ABC props on the way..the panthers are really good.. The ztw seal,k got that when they were cheap I see they have gone up alot in price..I did run the Sonicwake on 8s with the leopard 4082 1600kv was insane but the motor got hot and melted the connector and cogged,I used 53mm prop..to be honest I had a aquamarine 240A ESC and that ran cool on 8s so I'm not impressed with both ztw ESCs,200A didn't perform on 6s well where as the flycolor is exceptional but I do have big cap banks added

100% not,it's in an angle .The motor mount has to sit 100% flat as it is stock..

Paul Cooper thanks mate your help is greatly appreciated 👍

@@damienplumpton7069 Your welcome 😊

Hi yes will do asp 👍..it's persistently raining here and thunderstorms expected this morning ⛈️

Orange cooling block yes about $5👍

Hi I did have a vid up but I sold the boat and the buyer wanted to see vids and I thought he won't like this one,it flew 😊

I had to put this one on as my prop hit the rudder

@@paulcooper7162 pretty common ,mine has not done it yet but others have reported that .

@@fnkycoldmedina That's good..I only purchased the hull without the motor etc so I used my own gear,I now wish I had purchased the boat complete,a Sonicwake here in New Zealand is $949 including freight .A new miss Geico zelos is $1550 including freight

@@paulcooper7162 thats ok you did the right thing . proboat stock motors always run hot on 6s anyway .they always advertise 6s but use a 2000kv motor which should be 4s territory .1600 kv is better suited for 6s .my pursuit has a leopard 4082 1600 and goes 60+ with a x447 prop .

@@fnkycoldmedina Yes that's what i was thinking the Sonicwake system ran too hot..im happy I got the leopard 4082..60mph is really fast..