Proportioner Build & Test

Подписаться 5 тыс.

Просмотров 48 тыс.

50% 1

I built a proportioner for my soft wash system. I tested the ball valve on the water side to see if the draw is the same as the metering valve.
Updated 5/4/2024: Parts list for all fittings from Farmchem.com. Farmchem does not have the check valves so you need to get them from US plastics.com or another source. Just remember to make sure they are 1/3 crack pressure. You will need to purchase the metering valves separately. I went to my local pool company to purchase Pentair valves. I upgraded to the 1/2" Asahi valves from the Pentairs. You could also convert all the fittings to 3/4" for additional flow if needed.
3- HB050 (1/2" MNPT X 1/2" Hose Barb)
1-HB050-025 (1/2" MNPT x 1/4" Hose Barb)
1- CR050 (1/2" 4-way)
6- NIP050-SH (1/2" x 1.75" Nipple)
3- HB050-90- You can use this 90 or a straight fitting depending on your set up (1/2" MNPT x 1/2" 90 degree Hose barb)
3- 22210 (1/2" Check Valves from US Platics.com)
2- SL050-90 (1/2" Pipe Elbow)
1- HB050-075 (I chose to use this fitting from the proportioner to the pump. (1/2" MPNT x 3/4" Barb)

Хобби

Опубликовано:

2 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 291

@mattspontiacta 3 года назад

I run a ball valve on the water side and two Pentair valves for soap and SH. Ball valve stays open for a house wash I dial the SH between 1-2 number on the Pentair. Works good. I throttle the ball valve back a 1/4 turn for roof washing. I run the SH between 4-5 number. I run a NorthStar 7gpm pump 12 volt. Going on my 3rd year with that pump. I buy my SH at 10 percent. Pentair valves are going on 3 yrs with no problems. I run 200 ft of 5/8s flexilla hose. My system works for me no issues. I will say I tried running a Pentair on the water side at first and it restricted my vertical distance by 10 feet when it was on. The 1/2 inch diameter proportional system is restrictive in my opinion when running a 7 GPM pump. Now a 5.5 gpm might work fine. But just wanted to share what works for me.

@Under_PressureSW 3 месяца назад

What I’ve gathered from the pentairs are they are honestly the same when it comes to percentage. All the way (if you’re using 10%) would be a 50/50 mix which would be 5%. Half way would be 2.5% and so on. The numbers tend to scare a lot of people cause they think the numbers on the dials are 1%,2%,3% etc lol

@z3roxc00l9 Год назад

as someone who just took an interest in this trade, i was very curious how this setup worked, i was wondering if each tank had its own independent pump but i see now they do not by the looks of this video and use the same pump to draw each of the chemicals through the same pump out through to the main hose. so thank you for taking the time to demonstrate this and show how it all works and goes together.

@allproexteriorservicesllc5338 Год назад

Glad I could help. Thanks for watching

@docstevenamp 2 года назад

I've always suspected that the metering valve is BS. Running all inexpensive ball valves will be drawing the same abounts keeping the ratios equal.,

@LawrenceL1000 Год назад

“Hey catch up”.. I love it when you say that on your vids😂😂 Anyway there’s a brand ASAHI who’s metering valves design solved this phenomenon. By full open the metering valves practically the same inside diameter as the ball valves. If you look at the other metering valves the inside diameter at full open is way smaller than the ball valve, hence less flow! Wash on brother 🤘🏽

@allproexteriorservicesllc5338 Год назад

Good info. I just made some changes to my 12 volt proportioner with Asahi valves. Vid will drop soon!! Wash on brother.

@southeastsoftwash4020 3 года назад

Yep. I did that test a couple years ago. We utilize 3 valves because it’ll skew the ratios significantly.

@DougP1464 3 года назад

I found the exact same thing. with the valves all being the same metering valves it can be metered accurately.

@worth-fighting-for 3 года назад

@southeast softwash can I use 2 gf valves and 1 of the black and white ones (for water)?

@luxury65 3 года назад

@@worth-fighting-for use a regular ball valve for the water

@luxury65 3 года назад

@Steve Lagana yes I have

@frankpirrone6032 2 года назад

And if you have a broken valve, you can rob the water metering valve and replace with a ball valve temporarily

@KasonandJosh 2 месяца назад

With the check valve do you have to keep them up right? Or can they be sideways and still work fine?

@allproexteriorservicesllc5338 2 месяца назад

You can mount them upright or sideways. Thanks

@vr051964 3 года назад

Great Great Great video. Big difference!

@allproexteriorservicesllc5338 3 года назад

Thanks!!!

@jettbales8172 8 месяцев назад

Literally just bought everything out of your description. Wish me luck.

@allproexteriorservicesllc5338 8 месяцев назад

Not a bad build. Just don't over tighten the plastic fitting & use Tru Blue. Thanks

@jettbales8172 8 месяцев назад

@@allproexteriorservicesllc5338 Thanks, just got true blue yesterday. Still waiting on parts. Had some bad weather where I'm at the delayed things.

@law0472 6 месяцев назад

What was your total cost for the proportioner?

@allproexteriorservicesllc5338 6 месяцев назад

@@law0472 With the GF valves, the total cost is around $375. Thanks

@law0472 6 месяцев назад

Thank you I thought maybe us plastics was cheaper. I built one for about 295. On amazon. Thanks again

@8SecSleeper 6 месяцев назад

Use ball valve for all

@jbeezostl 10 месяцев назад

am I wrong in thinking you could just use all ball valves? wouldn't both h2o and sh being set on full open be 5-6% mix, set h20 full and sh to half, now you got 2.5-3% and so on. as for surfactant just crack it open till you like the draw.

@allproexteriorservicesllc5338 10 месяцев назад

I think you are correct. We wanted the ability to change the % when needed a little more accurate. Thanks

@manuelsuda 5 месяцев назад

I'm not the brightest light bulb, but is there a need to meter the water. Can you just run the ball valve for the water fully open. I understand it has a different flow rate from the pentair valves. But does that really matter. Please clarify. Also wouldn't more water flow be an optimal scenario. I don't know anything, I'm just trying to learn to set up for myself. Thank you

@allproexteriorservicesllc5338 5 месяцев назад

Yes, more flow from the ball valve will not give an accurate mix. Knowing the percentages with accurate valves equates to applying to correct solution & chemical savings. Knowing your chemical draw is key in the industry. Hope this helps. Thanks

@northjerseykevin3915 2 месяца назад

Great video. I often wonder if I could make them myself. Especially when I see the prices online and don’t know how they get away with those prices….. I guess some people can’t build things them selves. Thanks again for the video

@allproexteriorservicesllc5338 2 месяца назад

Very easy to build. But agree with the prices online. Thanks

@luisvaz92 3 года назад

For a 3000 CPM soap which vacuum pressure would you recommend to draw the chemical from the container. Great videos.

@allproexteriorservicesllc5338 3 года назад

Either a container or tank. Thanks

@StreamMastersPW 2 года назад

Hey sir, finished up my system and did a job went to rinse off the house with straight water but it was very soapy like there was soap drawing but my valve was off and the soap was not moving. It does not have a check valve like my other 2 lines. I rinsed and rinsed but still same result soapy water. Any ideas ?

@allproexteriorservicesllc5338 2 года назад

It sounds like soap got in to your water tank. You need to add check vales to the water line to prevent back flow. Thanks

@brycepridemore9864 7 месяцев назад

Do you think 3/4 inlet from water and same from sh would make any difference in this exact setup?

@allproexteriorservicesllc5338 7 месяцев назад

It may help a little bit, but it still a 1/2" on the 12 volt pump. Thanks

@brentbrowning Месяц назад

Hey, All Pro. Quick Question, why the 1/4 inch for the soap? does it draw less percent, saving soap? Thank you for the video and info!

@allproexteriorservicesllc5338 Месяц назад

Because you do not want too much soap. Remember, the more the soap the more you will need to rinse. Thanks

@brentbrowning Месяц назад

@@allproexteriorservicesllc5338 ah! Makes sense. Thanks for taking time to reply.

@rickyfriddle6439 Год назад

What is the enter dimension of the ball value vs the metering value?

@allproexteriorservicesllc5338 Год назад

I do not know that dimension. Thanks

@joshuapoche5137 Год назад

And whats the soap line for? Is that instead of just dumping the doap in the sh tank?

@allproexteriorservicesllc5338 Год назад

Yes sir! Also to control the amount applying. Thanks

@drowization 5 месяцев назад

Ok peeps, maybe I'm missing something here,,,, at 4:45 it looks like he has a 1/2-inch barb coming out for the water and the SH on the bottom of the unit on the left and right side,,,, then at 8:00 minutes on the bottom right and left sides it looks a 1/4-inch barb size coming out ???? and at 8:10 he says 1/2-inch barb, but they look like there 1/4-inch barbs,,,, what am I missing please ???? thank you all,,,,

@allproexteriorservicesllc5338 5 месяцев назад

Not sure what you are missing. I used 1/2" barbs on the H2O & SH & 1/4" on the soap. I did eventually upgrade the barbs to schedule 80 later. Still using that proportioner as of today until my next suace maker is complete. Be on the lookout. Thanks

@drowization 5 месяцев назад

@@allproexteriorservicesllc5338 Thank you for the reply, 1/2" barbs on the H2O & SH & 1/4" on the soap,,,, gotcha, thanks again for the help. when I ordered the parts, they sent me (3) 1/2 to 1/4 and just (1)1/2 to1/2 inch. so, I was bit corn-fused, lol.... but I got it now,,,, have a great day....

@577buttfan Год назад

Im still using a 4gpm and 5 gallon bottle.i use a 1/4" ball valve to turn my SH on/off.I also use the same valve as a metering valve if the house isnt too dirty to save a little $.I really want this set up you are showing though.

@allproexteriorservicesllc5338 Год назад

It does help with accuracy for sure. Thanks

@jefftatman7809 7 месяцев назад

Nice ! We need to build one before spring. Can you post a parts list ?

@allproexteriorservicesllc5338 7 месяцев назад

It should be in the description. Also, make sure all fitting are schedule 80 & DO NOT use Pentair valves. Thanks

@joeallenpressurewashing 10 месяцев назад

What about if you used ball valves for all three lines?

@allproexteriorservicesllc5338 10 месяцев назад

It would work but hard to get an accurate mix with a ball valve. Thanks

@whipporwill2303 Год назад

Why don't you just use 3 cheap ball valves?

@allproexteriorservicesllc5338 Год назад

Because of the inaccuracy and not know the % of chemical. Thanks

@dallashudnall8847 Год назад

Where did you buy those and how much was that setup please I need to know

@allproexteriorservicesllc5338 Год назад

You can get the parts from US Plastics or another vendor. Not sure of the cost in today's market. Thanks

@ritmolatino1627 7 месяцев назад

wonder if any one knows how will they be set to percentages needed?

@allproexteriorservicesllc5338 7 месяцев назад

Exact percentages is tough. I use the theory that wide open is 6% & half open is 3% etc. Assuming I am using 12% SH. Thanks

@BornOfAsh 2 года назад

Where do I get those Ryobi tips at? Can't find it on amazon

@allproexteriorservicesllc5338 2 года назад

I got them from Home Depot. Thanks

@realoakoutdoors6243 Год назад

What size pump are you using? Gpm?

@allproexteriorservicesllc5338 Год назад

We use the 5.5 GPM pump. Thanks

@dantec8854 Год назад

Have you add a blend manifold to your system?

@allproexteriorservicesllc5338 Год назад

Yes, for both 12 volt & AR45. Thanks

@merckling56 6 месяцев назад

Why not just use regular valves for all

@allproexteriorservicesllc5338 6 месяцев назад

It is tough to meter a ball valve and know the %. Thanks

@joshuapoche5137 Год назад

So if youre using 12.5% sh, with both valves open would that be your 6% mix and the more you shut sh valve off the weaker the mix?

@allproexteriorservicesllc5338 Год назад

Correct. Turn the SH valve to half way to get 3% etc. Thanks

@joshuapoche5137 Год назад

@@allproexteriorservicesllc5338 thanks man

@RobCC100 4 месяца назад

Do you have a part number for the metering valves you recommend? I searched the ashai metering valves and they are selling $175 - $225 each. Does that price sound right?

@allproexteriorservicesllc5338 4 месяца назад

Yes, the price seems correct. The part number for the 1/2" is 160521005. You could also go with the 1" & reduce it to 1/2" for future upgrades. The 1" is the same price & the part number is 160521010. I purchase my valves from Indelco. www.indelco.com/products?s=asahi&f%5B0%5D=category%3A522&f%5B1%5D=pipesize%3A29

@577buttfan Год назад

Damn,that ball valve is flowin!! I see this set up is only for batch mixing for roof washing and such with 12v.Good info!!

@Wuploads 2 года назад

Hi Pro. This valves are not too bad, but my setup start leaking after 2 years of use. I'm planning to get the more expensive ones, the one with the orange valve. Did you have used them before? Greeting from Miami Fl.

@allproexteriorservicesllc5338 2 года назад

The GF valve are much better that the Pentair valves. Thanks

@MarkB-zt9jm 3 года назад

Damn good video man ! I always wondered about a regular ball valve for the water

@allproexteriorservicesllc5338 3 года назад

Thanks!!

@tjmars37 Год назад

What if you did a smaller ball valve?

@allproexteriorservicesllc5338 Год назад

Not sure, but it may work. I just wanted to take the guessing out of it. Thanks

@captaincake4331 7 месяцев назад

Will this work on a gas system?

@allproexteriorservicesllc5338 7 месяцев назад

If it is 1" then yes. You would also have to turn on/ off the SH & soap manually. Thanks

@captaincake4331 7 месяцев назад

@@allproexteriorservicesllc5338 So is the only difference the 1" valves? Are all the other parts the same or does everything have to be 1"? I appreciate the video and your responses! Thank you.

@allproexteriorservicesllc5338 7 месяцев назад

@@captaincake4331 Ours is 1" on everything expect the bypass hose which is 3/4".

@javiernunez5299 10 месяцев назад

Have you try to us a ball valve on the SH and soap?

@allproexteriorservicesllc5338 10 месяцев назад

I have not. I decided to just use the metering valves. Thanks

@frankpirrone6032 2 года назад

You’re blending 4% at most, NG

@NestorDelatorre-ms4fm 6 месяцев назад

Great video. Thanks for the priceless info

@wehttamgtrekce 2 года назад

Great video! Why not just slightly close the ball valve down to match the flow rate of Pentair when spraying with bleach? And when rinsing turn the ball valve fully open so as not to starve the pump and get maximum water volume?

@allproexteriorservicesllc5338 2 года назад

That could have worked, but I wanted a more accurate flow. Thanks

@BobMcHatchet 4 месяца назад

thank you, i wasnt expecting a significant difference honestly. but it was very significant.

@allproexteriorservicesllc5338 4 месяца назад

That was my thoughts as well. It does matter when trying to dial the % in. Thanks

@mercilessgamer9676 3 года назад

Great video! Do you know if the size of the inlet hoses will affect the ratio as well?

@allproexteriorservicesllc5338 3 года назад

Not sure about the hose size. I chose to run 1/2" & 3/4" from the proportioner to the pump. Thanks

@J.Plunkett 3 года назад

Do the lines from each tank have to be the same length going to the mixing valve? Will different lengths of hose effect draw?

@allproexteriorservicesllc5338 3 года назад

No, my lines are different length. Once the lines are filled, then you are good. Thanks

@lemoslak Год назад

What is the best sealant?

@allproexteriorservicesllc5338 Год назад

We have had great luck with Tru Blue. Thanks

@thomasarnold950 3 года назад

Thank you for your help, I got my parts in and built mine off your video, Seems everyone one else just want to sell us new guys an way over priced class.

@johnabrams8729 3 года назад

Will this proportioner work with a 5.5 gpm machine for softwashing? Or is this better suited for roof washing with a 12 Volt?

@allproexteriorservicesllc5338 3 года назад

Better suite for 12 volt. Thanks

@xtremepowerwashing1815 3 года назад

Water line does get turned off when priming soap and sh line and flushing sh valve...can also be turned back to achieve a stronger mix when needed but not often as long as you have potent sh..pentair valves are trash...they all Crack..

@ezlimo9454 2 года назад

How can I buy all those parts live in California

@allproexteriorservicesllc5338 2 года назад

Not sure about California. You should be able to order them since there is no chemicals involved. Thanks

@ezlimo9454 2 года назад

Thanks

@henrysaldana1 2 года назад

How is it holding on?

@allproexteriorservicesllc5338 2 года назад

The pentair valves did not hold up well. I switched to the GF valves & they have been solid. Thanks

@SierraWater 3 года назад

The ball valve is full bore with a much higher Cv (Flow Coefficient) than the non full bore lower Cv Metering (Plug) valve at full open.

@vladius8521 2 года назад

and the pump your using and its plumbing

@michaelvinalon3415 3 года назад

Nice test ! Thanks for going through all the testing. Excellent information. I guess it’s gotta be apples to apples. Thanks 👍🏼

@jaystuart4256 3 года назад

You got a parts list . Thanks alot . I setup an account with us plastics just because of this .

@allproexteriorservicesllc5338 3 года назад

Jay, I have the parts list in the description. You just need to get your valves. Let me know if you need anything.

@rcl700 3 года назад

Have you had any issues with having a bulkhead in the bottom of your chemical tank? I was told the SH will damage the fitting and leak.

@allproexteriorservicesllc5338 3 года назад

I have not had any issues. But I plan to change the tank to a 100 gallon with no bulkhead fitting.

@rcl700 3 года назад

Why no fitting?

@allproexteriorservicesllc5338 3 года назад

@@rcl700 Fitting in the bottom is a potential leak.

@justinsmudde2554 2 месяца назад

Great Vid! Thanks bubba

@vladius8521 2 года назад

need video on now-watching you flush lines correctly

@magnumopusdesign9148 2 месяца назад

Just subscribed b/c of this video. Thank you! Curious thing, Mike V said a ball valve is more restrictive than a gate valve. Are GF valves gate valves? If not, what is configuration of "metering" valve? Thanks!

@allproexteriorservicesllc5338 2 месяца назад

The GF is not a gate valve. They are metering valve that allow the flow to be metered. We now use the Asahi metering valves on all out or proportioners. Thanks

@davidstearsraingutterclean6729 Год назад

Use a sweeping 90

@newviewnc 2 года назад

Hey brotha. That part 62119 (1/2”MNPT x 3/4” barb, would that be the same part I’d use where the hose comes in and out of the pump? I think those everflo are 1/2” in and out no?

@allproexteriorservicesllc5338 2 года назад

I used the 1/2" x 3/4" from the proportioner to the reel. I know it reduces down but thought it may help. You could use 1/2" x1/2". Thanks

@enjoythesho1992 Год назад

You could adjust the ball valve to match and save 50 bucks

@allproexteriorservicesllc5338 Год назад

You could, but the ratios may be off a little. Thanks

@powerfulimprovements 3 года назад

Great video.

@allproexteriorservicesllc5338 3 года назад

Thanks!!

@martinsaenz8683 3 года назад

Awesome content you got yourself a new subscriber 👍

@allproexteriorservicesllc5338 3 года назад

Thanks!!!!

@tomuzagregv.8300 2 года назад

If by chance you want to 3way off the output side to switch draw from a 12v “or” a Downstream injector, you’ll need a meter valve on water to shut off water completely to meter for Down stream. Also you need check valve on all as well!

@luckycollins1431 3 года назад

one thing... I haven't watched you full video yet but every other video I have seen never even tells the size of their hoses.... it really sucks.

@allproexteriorservicesllc5338 3 года назад

I have multiple videos with details on the channel. Trying to give as much info as I can and respond to comments. Let me know if I can help with a hose size. Thanks

@blane9906 2 года назад

How do you prime the soft wash system and then when you change the dials, how do you know when the new desired amount of bleach is coming out of the wand? Thanks!

@allproexteriorservicesllc5338 2 года назад

It self primes pretty easily. It takes about 30-45 second to clear the line when changing the SH dial. Thanks

@josephsawyer5113 3 года назад

What kind of hoses do you use from the manifold to the tanks?

@jonboysprowash7845 2 года назад

Nice test. I just asked this on a Facebook page today. How long did the Pentair valves last?

@allproexteriorservicesllc5338 2 года назад

They didn't make it to long. I would highly recommend the GF valves for sure. Thanks

@hawespipe Год назад

What type and size bulkhead fittings do you use? 1 3/8 to 1/2”

@allproexteriorservicesllc5338 Год назад

1/2" Thanks

@carpetmagicofwilson 3 года назад

Great info thanks for taking the time to do the test, I am ordering all the parts to build myself one. If i get to doing this full time i step up to the GF valves. But if you keep these clean and take care of them they might last and work just as good.

@allproexteriorservicesllc5338 3 года назад

Agreed!! They have been holding up well so far. Thanks

@beneast5216 Год назад

can you do a test showing how you would mix ratio's to figure out how you want it set on the metering valves?

@allproexteriorservicesllc5338 Год назад

I will try to get it done. Thanks

@tonybourget9809 Год назад

Do you have a video on the mix ratio for the metering valves? This is the only part I am lost on

@allproexteriorservicesllc5338 Год назад

This video may help. Thanks ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ZnZnkNADhOs.html

@dannyblankenship4144 Год назад

Thank u very much for taking the time to do this test and video. Dont think u realize just how much time & money u have saved me as well as everyone watching this video.. Absolutely great helpful/ informative and educational video.. much appreciated my brother...!

@allproexteriorservicesllc5338 Год назад

Danny, thank you for watching & glad I could help! I really appreciate the comment! Wash on Brother!

@johntilson3718 2 года назад

Great video thanks very much

@allproexteriorservicesllc5338 2 года назад

Glad I can help!! Thanks

@hobbieprofessionalservices2454 3 года назад

Great info! Thanks for doing the test, was always wondering what would happen.

@allproexteriorservicesllc5338 3 года назад

Thanks!

@razerray2000 3 года назад

Next time try a little food coloring in each test tank it would show up better for your water levels.

@allproexteriorservicesllc5338 3 года назад

Good idea. Thanks

@Imjustherevibin 9 месяцев назад

Great tips....

@webcrawler3332 2 года назад

Pentair valves is all you need. They are made for chlorine and the more expensive ones aren’t needed.

@allproexteriorservicesllc5338 2 года назад

Every Pentair valve I had ended up leaking. In my experience, the GF valve hold up much better. Thanks

@marcuswalker9172 2 года назад

I have a REMCO 7 GPM pump what size hose should I be coming off the pump to the manifold ?

@triplehbkundertaker1 3 года назад

What would happen if you maybe used a 3/8 ball valve instead of a 1/2 inch control for the water, I’m thinking this may work

@allproexteriorservicesllc5338 3 года назад

It may work, but 3/8 ball valve may be hard to find. I would recommend just using a metering valve. Thanks

@jeffellis7348 3 года назад

I did this same experiment but i used two of those 1/2" ball valves in series for the water. The one closest to the cross stayed closed but i drilled a hole through the ball to imitate the resistance i was getting on the metering valve. The second valve was my shutoff. It took some fine tuning but after I got it it stayed consistent on the draw rate. My metering valve cracked recently so I may see if I can do the whole module similarly. I can buy the metering valves but I enjoy the tinkering.

@allproexteriorservicesllc5338 3 года назад

@@jeffellis7348 Awesome!! That is the way I am as well. Thanks

@johnabrams8729 3 года назад

Hello, I'd like to order one of these from you, if you make and sell them . Could you let me know?

@allproexteriorservicesllc5338 3 года назад

John, unfortunately I do not sell them. However I can assist with the build if needed. Thanks

@zadok22 3 года назад

use two 45s in place of a 90

@allproexteriorservicesllc5338 3 года назад

Yes, the 45's would be better for sure. Thanks

@ashleycowart1937 3 года назад

Assuming the flow rates remained consistent day to day on the first test, wouldn't that result in about 3-4% mixture and more flow overall? Curious what the comparison would be in gpm for the ball valve/pentair vs 2 pentairs wide open.

@allproexteriorservicesllc5338 3 года назад

Not sure about the GPM test. However, with a ball valve flowing more than the Pentair it would dilute the SH%. The pump is only a 5.5 GPM so not sure about the extra flow. Thanks

@henrydixon3159 Год назад

Do you have part list for all the parts that is needed to build a proportioner valve?

@allproexteriorservicesllc5338 Год назад

It should be in the description. Thanks

@mauriciom.868 2 года назад

Super awesome video !!!! Thanks a lot friend and much luck with your business … thanks again!!!

@EdgarasVisniauskas 2 года назад

Sorry for silly question, but shy do you use a check valve?

@allproexteriorservicesllc5338 2 года назад

So you don't get back flow into your tanks. Thanks

@ivanbaez3606 3 года назад

Good job man can you please put all the parts list?, Thank you.

@allproexteriorservicesllc5338 3 года назад

Yes. I will add the links to all the parts. Thanks

@allproexteriorservicesllc5338 3 года назад

Parts list added! Thanks for watching

@williamtemple4331 3 года назад

Great video. I liked your trailer build also.

@Johnnyreengo 2 года назад

Does your flexzilla hose not flatten out and restrict flow when on the hose reel?

@allproexteriorservicesllc5338 2 года назад

We always take the feed hose all the way off the reel to maximize flow. Thanks

@stefansmith6483 2 года назад

Metering valves it is get the right mix and in the end save on water and chems means saving a bigger 💰

@allproexteriorservicesllc5338 2 года назад

Agreed!! Thanks

@lDubstepTime 3 года назад

Anyone able to find these parts in canada? Looking to buy or build one but parts are never in stock or extremely over valued

@allproexteriorservicesllc5338 3 года назад

Not sure about Canada. I wonder if US Plastics will ship to Canada. If I hear of anything, i will let you know. Thanks

@lDubstepTime 3 года назад

@@allproexteriorservicesllc5338 ended up finding a plastic place that had 80$ of the parts and just bit the bullet on ordering the other 20% on US amazon and paying import + shipping

@squares357e 2 года назад

Great information. Do you have a parts list?

@allproexteriorservicesllc5338 2 года назад

In the description. Thanks

@erikservices 3 года назад

Thanks for sharing

@vladius8521 2 года назад

would you be willing to look at my setup and give me a opinion as to proper soft wash setup and im severly unhappy with my current pump for softwash?

@thomasstutes7125 Год назад

If you have a three-quarter inch line against a half as would it be different you had three quarter against see what it pulled

@allproexteriorservicesllc5338 Год назад

I think it would change, but we run 1/2" all the way. Thanks

@halls24hr Год назад

nice trial i was cwondering also bout if it really mattered thanks ...channel pressure washing with love

@nestorortiz5866 Год назад

Is called common sense, the meter valve is measured and smaller ball opening, but no need that meter valve

@michaelhebert8197 3 года назад

What if the ball valve was smaller than the 2 metering valves? Maybe it would equal out then?

@allproexteriorservicesllc5338 3 года назад

It may work. But if you are only doing roofs through the proportioner, then 2 ball valves would work for sure. You would just always have a 5% or 6.25% depending on your SH concentration.

@justinsmudde2554 2 месяца назад

It’s drawing 100% more water than chems.