Тёмный

PVC Clam Gun Modification Failure!! 

What's Mike Doing?
Подписаться 557
Просмотров 1,6 тыс.
50% 1

I purchased a PVC Clam Gun and tried to modify it so it would have a vacuum relief tube like the more expensive ones. I then tested it while digging for Pacific Razor Clams at Ocean Shores Beach in Washington State USA. My modification did work a little bit however I believe the tubing was too small of a diameter to be truly effective at relieving all the vaccum. The duct tape was a lot more temporary than I was hoping.
As a side note this is my third video and was recorded on a Garmin Virb Elite action camera without an external audio source.

Развлечения

Опубликовано:

 

27 окт 2019

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 12   
@kanakanorcal2565
@kanakanorcal2565 3 года назад
Install a nut on the inside bottom. Then take a countersink screw with most of the threads removed to make a valve to keep the sand out when pushing down. The valve will open when pulling up if the fabrication is done correctly. I used an angle grinder with a cutting wheel to groove the screw in four places to allow more air to flow.
@whatsmikedoing8761
@whatsmikedoing8761 3 года назад
Thanks for the tip!!
@epicgamesclan6685
@epicgamesclan6685 4 года назад
Nice job dad
@whatsmikedoing8761
@whatsmikedoing8761 4 года назад
What is Ethan doing? #1 Thanks Bud!
@rileywoods6801
@rileywoods6801 4 года назад
I like the intro Mike! I’ll keep coming back! Good content!
@whatsmikedoing8761
@whatsmikedoing8761 4 года назад
Riley Woods thanks for the support man!
@alvinherrera5139
@alvinherrera5139 4 года назад
God bless you always brother
@whatsmikedoing8761
@whatsmikedoing8761 4 года назад
Alvin Herrera Thanks again champ 😁
@thelowrangers7835
@thelowrangers7835 4 года назад
Hose clamps?
@whatsmikedoing8761
@whatsmikedoing8761 4 года назад
The kind with a screw would make it harder to push in the sand as they’d stick out but actually the flat strap kind that get installed with a tool could work. Like the pallet straps.
@PhilogusRex
@PhilogusRex 4 года назад
Imagine you both with no ears, that might be entertaining...
@whatsmikedoing8761
@whatsmikedoing8761 4 года назад
PhilogusRex well we both wear hearing aids so we’re close to having no ears 😂
Далее
All About a Clam Gun, You asked for it, here it is.
7:43
Smart Sigma Kid #funny #sigma #comedy
00:26
Просмотров 12 млн
Digging Razor Clams with Dale Murff
16:22
Просмотров 23 тыс.
Easy Way to Clean Razor Clams
6:43
Просмотров 74 тыс.
RAZOR CLAM GUN BUILD
9:37
Просмотров 8 тыс.
"Digging" Razor Clams with a Clam Tube (Clam Gun)
7:27
How to Razor clam in Long Beach, Washington
10:43
Просмотров 10 тыс.
To preheat or not to preheat, that is the question!
13:04
Traditions Hawken Muzzleloader kit do's and don'ts
5:55
Clamhawk Razor Clam Gun - voted BEST on the beach!
11:29
Grant's Getaways:  Razor Clams and Tools to Dig Them
5:53
Пранк над Махачевым🥶
0:19
Просмотров 9 млн