Rc Lawnmover from Hacked Hoverboard 

Thanks for the comment!

@@snowkingcro The only problem is that the motherboard shots off at 38v

If you need 5V for the RC Receiver, you can use 5V from Hall sensor!

@@snowkingcro I'm already using 5v from hall sensor. But that doesn't solve the cott off problem .

well... i had that problem... i woukd try to charge up the batterry to 100% (~42v), and flash again... maybe the borad reads that the batery is dead at 38v...

Thanks. The wiring has only one difference, and that's the ADC1 for steering and ADC2 for throttle. To better clarify, ont this video ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2Zg-sp9BD_g.html it can be seen on 3:00 min. mark!

​@@snowkingcro 3:19 is the only close up I see and even that is not clear. It looks like you are taking 5v from the right hall cable to power the receiver (White wire). But then you have three wires. I'm guessing you are using ADC1 and ADC2 and GND raw.githubusercontent.com/NiklasFauth/hoverboard-firmware-hack/master/pinout.png But I have no idea how you connect those to the receiver. Is ADC1 just going to the signal port on channel 1 and ADC2 going to the signal port on channel 2 and power and ground going to any other channels power and ground?

I used 5V from hall sensor and adc1 adc2 and ground from from the left sensor board.

snowkingcro but how does that connect to the receiver on the radio?

i'll post a picture in my repository and send you the link.

Do you mean the cables on the Hall sensor? No, not at all, just keeping the wires short

They tend to be warm but I had no problems whatsoever. It works aprox. one hour per moving, so... it gets warm, but thats it... I can hold to the wheel with my hands

Well, I bought some sensors to implement with an arduino board, but i'm stuck due the lack of free time :/

Even some used ones come with a little seat with the third wheel.

On this video, look in the comments, there is the link to the Firmware

The hex code to flash your board can be downloaded here: github.com/snowkingcro/hoverboard-firmware-hack-esk8/tree/RC-Steering/build Or you can find the link in the description of my video. You can use any 2-3 channel radio remote. Cheers from Croatia ;)

@@snowkingcro Thanks for the reply! I would like to build a radio-controlled lawnmower as in the video, which firmware should I use? On the site I find two versions of the firmware. One file has the word master at the end of the name and another file the word sterring. thanks again for your kindness. ps: is there a connection diagram? from the video dive you explain the connections is not clear. Thanks from Italy.

Hi. use the steering FW, and as for wiring on this link: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2Zg-sp9BD_g.html on the 3:00 mark is the wiring diagram

@@snowkingcro I built mine about three weeks ago, and I wish I'd seen your great video before I built mine. I would've made some changes especially with regard to the wheels. Your setup allows for zero degree turns, mine sorts does it too, but because mine is four wheeled, with the rear wheels being the powered wheels, it requires more power to achieve the zero turns. You did and excellent job with yours. Kudos!

Na ovom videu ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-2Zg-sp9BD_g.html na 2:54 je slika, koju treba pauzirati. Transmiter je spojen na LEFT SENSOR BOARD

thanks 😊

hm, želiš upravljati hoverboardom kao ja na mom videu? Pa, morat ćeš flashati firmware od hoverboarda sa firmverom u linku ispod videa... ali upamti da je to nepovratan proces, pa ako to napraviš, nećeš ga više moći vratiti na funkciju hoverboarda

well until now i flashed three boards, didn't checked which chip it was...

well, i think it could be the problem with long cables, always try to keep them short. i really didn't have any problems, but i got some reports of my friends that certain motherboard react different to the code upload.

@@snowkingcro often thicker wires helps reduce voltage drop over distance. Not sure how it correlates to data, but considering cat 6 is just thicker cat5 I imagine it’s something similar with data

Jel si uspeo to napraviti ja pravim nesto slicno