Reach in freezer is not getting cold enough 

Man you made it look simple no equipment is made to last long sad its just the truth Great job

you are a great teacher I wish you could be my mentor I learn more from you than the techs at my own job

EXELENTE JOB. Thanks for sharing

Awesome job compresses are not made like they used to be 👍👍👍

Another great video💯. Following a consistent troubleshooting procedure insurers you get to a accurate diagnosis quicker. 👊

best HVAC video. please keep making great video, I have learn a lot thank you.

Such awesome teaching and vídeos I’ve been learning how to charge this kind of equipment more acutely thanks to you , thank you God bless

Could also possibly be power supply issues. Here in outback Australia we often get "Brown out" situations where the incoming power supply drops down from 240V to a low as 150v sometimes even less (Or power surges during electrical storms) Compressors don't like that... especially 3 phase. It's may be unlikely but just food for thought. Knowing how meticulous you are, i honestly doubt you have done anything wrong here! Great video 😊

I believe True freezer the want to see a 10 degree T.D.whereas true coolers a 20 degree T.D.at least what i was told when i inquired about this...good concise vid

Another great teaching video. In regards to HH liquid line driers, I have installed many of them on systems after burnouts. I have never installed them on small cap tube systems, though. Let me know what True says. Keep your head up and keep teaching.😊

Just found your channel, awesome resource. Any chance there’s a link or for your troubleshooting checklist anywhere?

I believe its restriction or moisture

We had a few compressor with a trip to was broke off internally in the compressor off of the muffler. So the compressor is locked up shortly after startup. Things happen I wouldn't sweat it. You do good work. Hopefully you get paid for the call back

👏👏👏👏Nice job as always. I had a similar service call on friday, two years old glass door cooler with high low pressure(110 psi) / low head pressure(125 psi) - R404a. The owner didn't want to believe when I told him it was the compressor. Did the same procedure you did just to be sure, recovered the charge, did a deep vacuum and recharge but I got the same result. New compressor coming next week.

Equipment these days are getting worse. Unfortunately 🙄

Two expensive walk in compressors failed on me in one summer right after the install. I drove 5 hrs round trip to pick up the warranty replacements and installed them just the same. This was 4 or 5 yrs ago and both are doing fine. Sometimes the these vapor pumps fail, even if they're new.

👍🇺🇸💪❄️ Great honest video thanks I do have a question about condenser split did you have to check with the manufacturer or because it was a newer unit u went with 15 ? If u went with 25 cs the high side would b spot on 195psi.

It would be interesting to cut open the failed compressor and see what the actual failure was

WHEN possible always cut the line do not unbraze,you could have tried reversing the compressor to dislodge the speck of dirt on the valve,thanks for sharing.

HOW DO YOU GET YOUR CONDESNER SPLIT

Unfortunately parts & equipment getting worse these days put in a Sporlan 032 Cap tube drier .

Good video. Question for you, how do you determine the condenser/ evaporator split temperature?

Not because parts are new, are working properly. Every time I get sent to a pm and new units are installed, I always find something. Either something in the install work or from manufacture. A Lennox RTU used as DOAS but the roof curb was open to the unit return from supply and a manual damper open in the return. The thing was recirculating air within. Heat exchanger overheated the entire winter. And unit didn’t work properly in summer for cooling as it would bring on heating right after cooling because the temperature in recirculating air. The worst part, I my visit was the second pm our company had made in this new building. I always see opportunity to find issues in new equipment. And that’s why I alway say “ not because is new, works as it should “. I have found units with no crankcase heater when should have.

Has anyone had issues with the drain tube on the true reach in’s freezing and backing up with a good heater? What was your fix?

did you flush system after first replace compressor? or good way is to mount Suction Line filter drier like a danfoss das08x series or castel or emerson, to catch any acids, contamination or debris

Boss I want to know that if I want restaurant reach in normal temperature freezer convert to deep freezer how can did it.please tell me.

No word

how do I calculate the suction pressure, and in some earlier videos you calculated the current temperature of the box and now the desired temperature, which method is better? Thanks in advance

What caused it to go bad so soon????

desired box temp-TD(20)... is it always a 20* TD?

did he just check for a Burn out even tho the compressor is not pumping .... wow SMH.....