Last week we built a motor run stand and this week we rebuild a 350 and run it on the run stand. Check out my merch!! thisnthatgarag... Facebook: / thisnthatgarage Send me stuff!! This N That Garage PO Box 489 Pleasant View, TN 37146
Very entertaining video. Engine test stand looks solid as a rock, and the engine is running really smooth. Always glad to see a cameo appearance by Ms. Daisy too.
It's a fantastic day when you get to watch a brand new video with this n that garage!!!!We wait for the video all week long!!!!Thank you for the enjoyment!!!!!Have a blessed day!!!!!?🤓🙏
“Always do the stuff you like first. If you wake up dead tomorrow morning, you will have done stuff you didn’t like and didn’t do the stuff you did like. So, always do the stuff you like first.”- This N That Garage - That’s one worth writing down.
On our Sea Scout boat, we got a Chrysler 318 marine with a Carter 4-bubble. That salt cleans off the carb using CLR calcium, lime and rust remover. Swab it on liberally with q-tips and it takes it right off and stays off until the next time you go driving in the salt.
You should call the Dodge, Red Dog! It's been dogging you every step it away 😂 your run stand looks really nice in red and your engine build turned out really well. Through the termination and tenacity you gut er done 👍 another great video Chad ✌️🇺🇲
I don't know how many times I sat as a kid watching my Dad rebuild engines, homing was always fun to watch, that carberator mercy sakes good thing she didn't blow.. 👍👍👍
One of my favorite tube channels. I enjoy your down and dirty yet methodical approach to automotive mechanics. Looking forward to the next episode(s).👍
Well Dangggg feller !!! Matching sparkplug wires with that "High Plains Drifter" Red Engine helm ! She's a Beauty! That's some uptown fabrication right-char. Before you revealed to us the Rad cap incident I stopped the tape and slow mo'ed it and damn Chad,, you were damn lucky. That cap was moving !! Woulda have seriously messed you up, thank heavens you're ok. You wouldn't believe how anxious we get watching waiting for that engine to bust off, it's thrilling as hell. Another fine video from Chad.. He's not as smooth as Tennessee Whiskey, But he's as warm as a glass of Brandy 👍 Excellent content.
thank u sir for your time making this video and bringing back some good memories. early 90s we had drag racing with a class called bone stock, your 350 could be bord has big as u wanted to go, whole 9 yards with crank and rods, but u had to do it with a stock block and heads with a 2 bl of course. seen A LOT of guys blow the bottom end out of an engine. that's what made the class so fun. u could go has radical as u wanted, but a stock block can only handle so much. class was very competitive. people nowa days don't have extra money to play with. again thank u, I'm sure it take a good minute to make and edit a video.
Hey Chad... old parts guy here. I don't remember everything that fits everything anymore (lol), but I do remember how to use reference sources, and they say that the S-402 cam gear fits 318, 340, and 360 ChryslerCo engines. To be sure, check the crank gear... it would be an S-297. Looks like they pulled parts on a Friday! The set for an '82 Chevy 350 (VIN code L) would be the C-3001K for the silent-type chain and gears, and C-3023K for the roller type set. Love the channel... love the content!
Nice job again, I’ve built probably a couple hundred engines of all sorts over the years and countless partial engine repairs …From v10s to Yamaha v8 to simple little 4 bangers, and of course all the regular v8 stuff. Even tho i thoroughly enjoy building engines it’s fun watching others build then too! Watching for a little trick someone does for my next build or catching a mistake they did! That thrill of firing up a fresh engine and it does what it’s suppose to do if ya did everything right…if not it can be your worst nightmare! 😂
Another great video. I learn so much from your videos. Thanks for the knowledge and the laughter. Engine stand looks rock solid 👌 Looking forward to your next video
I'm happy that cap didn't take your ear off my brother. I want a stand just like that so I can hear a small block 350 sound off any time of day or night. Yah buddy!! Thank you.
Gas-ka-leens, car-ber-roster, hamma, thing-a-ma-bob, dad-blame, right-cheer - I am from the south and understand everything you are saying sir. I love the fact that you are a master of the southern vernacular. My favorite is gas-ka-leens through! Y'all be good up there in eastern, TN, stay warm and Ease Up every chance y'all get!
Name for the Dodge short and sweet call it .(headache) She still has a headache from the tree branch and she give you a headache every time you look at her 😂 and by the way the running stand I love it.
Hi Chad i was telling u while watching the video like "hey buddy u forget to install the oilpump"but yes shit happens when u loose focus but i believe it happens in the best of families thanx for another excellent video lots of love from S A
Love all the gm 350's, and I think ya got a good one here. Hope it works out for you and the older gentleman without trouble! Keep up the good stuff my friend!
Just a helpful cleaning piston hint. I use a crock-pot & put antifreeze in it (50/50 mix) set on high & clean-em-up. Works grrrrrr8 on carboraters too .... 👍
Some of folks feel a little cheated! You didn't show or say anything about painting the stand, that sweet red! Just kidding, but that would of been a nice add on to this episode. Congrats on this success!
Holy bajesus I laughed waaayyy to hard when you dodged that radiator cap! Whatever you do don’t give up RU-vid! You’ve got a gift sir, and it’s entertaining us good ole boys !
I'm Surprised you couldn't hear me screaming form Ohio "DID YOU PUT THE OIL PUMP ON". Love the engine stand, you need a hose bib shut off on the lower hose so you don't drain the radiator each time you test an engine. Lots of fun, Thanks
A country dude keep it up man you do some extra homework make me wish I was still living in the country working on motorbikes and go cars and Hot Wheels laugh out loud
The engine test stand is built perfectly fine. Only one change I'd make is how you have that back plate holding up on the side post by the pitch bolts. Those vibrant loose the motor is going to slide down. Maybe drill thru holes like 6 of them to adjust in the upright posts part and put a pin so there is no chance of that sliding down. Other then that it's good to go 🍻 and as far as those square plug. They sell different size sockets for that. Look up male pipe plug sockets. Buy a set of them. We use them alot in heavy equipment industry 👌
It was nice that our region finally warmed up a spell, but last night and for the next couple days, us Tennesseeans get to bundle back up for the weekend!
Motor runs smooth as silk ,testament to a job well done . Strange about the thermostat not letting the motor warm up with the three holes drilled in it. minor thing !!!! God Bless you and yours, stay safe and well ,Stuart in Ontario...
Another great build Chad she's running like a smoothie, looking forward to the next one , oh by the way when are you going to call one of your trucks miss daisy ?? Always look forward to seeing her and that would make a grand name for one running nice and smooth .
I like the run stand. I've watched a lot of videos on engine rebuilds and I think you missed your calling at instruction and keeping your audience captured on a professional level. Your tops!
👍Nice build. Also, nice “dodge” from that radiator cap 🤣🤣🤣 It was just excited to be operational once again. Sounds great! Glad to hear you’re getting the trusses! Won’t be long now! (call the ol Dodge “POS”🤣) Good stuff feller! Keep up the good work.
Another great video. Every day I get on RU-vid looking for something from you and I’m always really happy when there is something we learn things from you but you’re entertaining as heck. Thank you so much.
Little trick on small buck Everly is the only Motor it works on man told me about this was 90 years old and my grandfather Mecanic 2 started out as an engine builder and one of the biggest abs in Illinois. He said on a small block Chevrolet you can set the distributor in it and pointed towards number seven plug wire and never have to move it again it’ll fire at Pratt.
