Mobile Super branches Shredder - Machine Build (fail?) 

I wanted to say you have amazing ideas and you build the most amazing things !! Things break it happens ...keep going I believe in you !! You will be back !!

Another top-notch video. Excellent craftsmanship, fab skills, problem solving, welding, machining, etc. I have learned so much watching your projects over the years. Please keep up the great work!

Two thoughts_1) Maybe make those blades replaceable. 2) At least heat treat and temper the blades if you are going to ing to welded them in place,then they’ll last a bit longer.

Sukces polega na przechodzeniu od porażki do porażki bez utraty entuzjazmu. - Winston Churchill - nie łam się , świetna robota

The project may have failed but i learned a lot about the value of belt drive mechanisms in applications such as this and i thank you for that.

Jak zawsze fantastyczna robota 💪 aż miło się ogląda taki materiał 👍🏻 super sprawa! 👏

Cycloidal gears contact only on small part. I think it is correct.

Too bad with the gearbox, but don't look back in anger, it's a new challenge now! You can do it! The machine itself looked good, simple but probably very powerful, would love to see it operational... 👍👍👍

Może sam spróbujesz zrobić przekładnie ślimakową. Takiego filmu z własną przekładnią ślimakową dla rębaka jeszcze nie widziałem.

this is the first branch breaker that I have seen that pinches the branch from one side, I can only think that that creates the need for more pressure on the bearings and the gears, in order to break the branch, since it has to push the blade clear through the branch, other wise it was a good build, and a SUCESS, just needs some tweaking.

It seems pretty easy to make, but just picking it up and making it isn't for everyone. Great work!

Oh... Wow... 😮 Do you think it was manufacturing defect? Looks pretty weird!!! Either way, fantastic work as usual! 😃 Stay safe there with your family! 🖖😊

A belt drive with an engagement pulley on a spring could act like a slip clutch

Good idea, but problem using a gearbox is there's no give in the driving system, definitely needs like a belt and pulley.

Can double as a toe nail clipper!

Result is no matter but hard work is really appreciate 🙏 Great work sir I enjoyed the show thanks 👍 😊❤❤

Hmm, dlaczego napisałeś, że to przekładnia planetarna?

I like your projects. Next time I want to see HD shop press but with 20/32 ton bottle jack, which is flipped upside down and WHICH is driven by motoreducer and some special mechanism and not with hands. It will be fun. There is only one video in youtube of such a machine (by old russian guy)

Good job mister well done

Everything you made worked perfectly. The gearbox, which you did not make, failed.

Very good!

Very nice work sir

Well, you can't win every time. It was still a cool video.

Ze względu na to że tego typu maszyny mogłyby pracować na działce przy braku zasilania 220-240V, a w okresie jesienno zimowym szybko się ściemnia to można by zamontować małą prądnicę o napięciu wyjściowym 12-24V do zasilania oświetlenia.

That looks like a harmonic drive or cycloid drive, not a planetary gear set. I couldn't see the sun gear or planetary gears. The two center shaft ball bearings are offset and the counter weight balances the off-center load (similar to a crankshaft)..

Tough luck with the gear box. Keep going, you will dial it in.

🎉wow amazing 😮 work Plz can you tell which camera are you using for video shoot...?

Can you try to make a sawmill but with a circular saw blade on an electric motor that slids down a railing and stuff? I need some ideas on how to because i want to make one myself.

Time to get a CNC and MAKE YOUR OWN Planetary Gear Box!!! ;)

And the name of this device should be "bober, kurwa"😂😂😂

most of the commercial wood chippers seem to have a belt reduction

Лайк не глядя 👍

GREAT JOB AS USUALL.

Надо лезвия наточить - как - приварил ведь.

Brave ❤❤

Gear teeth probably where not hardened for such use.

Have you looked into- contacting a small machine/tool company about them sending you some new machines (ones that you otherwise wouldn't be able to afford on your own, like a CNC or a Lathe... but I'm thinking mainly a CNC) in exchange for a few Ad spots on your channel??? You do have OVER 1.25 MILLION subscribers, so companies are more than willing to send you9 their equipment so that their name gets heard but 10's or even 100's of thousands of people. RU-vid channels much smaller than yours do deals like this ALL THE TIME!!! Just yesterday I watched the newest vid from Not An Engineer and a company sent him a CNC for an AD read, and he doesn't even have 190k subs!! So you will DEFINITELY find a company that will do this! (that's IF you are interest in owning a CNC... or some other big machine you wouldn't otherwise be able to afford without a big bank load or something) And all he did was send the company an email (I'm not sure which company it was tho, or who he emailed in the company... I would think it would be the head of Marketing maybe 🤷‍♂) And asked them if they send youtubers their machines in exchange for an honest review... and they said yes they do. So i REALLY think you would have NO PROBLEM in having this happen, no problems at all. Well, except maybe that you have an accent.... so you WILL have to work on pronouncing your English with less of an accent, just because you will have to do some narration in the ad reads..... OR you could do something different like making the ad into a funny/comedy type of ad, and having a girl hold up a large piece of white cardboard with the narration written on it... and use some comedy like "accidentally" holding the board upside down... oh oh, along with showing the boards with the narration, YOU could be reading the narration out loud and the signs she is holding is acknowledging that you have a thick Polish accent, which it perfectly fine.. ( in America we are always hearing accents from all over the world, but when people actually know English but just have a thick accent, it still makes us happy that they know what they're saying in English... they put in a LOT of effort to learn English ) and when the girl "accidentally" holds the sign upside down, you would play that part of your voice narration IN REVERSE, but then just before she would be switching to the next sign, she realizes it backwards and flips, and then you voice switches to talking normally LOL (I know it's not really 'comedy' I'm just trying to give you some ideas for a unique ad read.... and this is IMPORTANT if you think you will ever want to do an sponsored video for another company because they will look at how you did the sponsored videos before that... so you REALLY want to make a great, high quality ad read video because other company WILL WANT TO work with you in the future :) OR... if you REALLY wanted to I could do the NARRATION for you (for Free of course... because I REALLY want to show some love and support to your channel because I've actually LEARNED ALOT just by watching you make stuff! and seeing you go from that very small tool shed to what is now a FULL MACHINE SHOP has actually brought me SO MUCH JOY just by watching you grow from what seemed like just a small hobby to you doing WHAT YOU LOVE TO DO, EVERY DAY!!! So I REALLY would want to give something back for all that you have given me.... but money is just something I DO NOT have very much of... I'm unemployed, living in my mother and fathers home while I take care of my senile, bedridden mother and also all that goes along with keeping a house running because my father is on Oxygen and can't even walk to the bathroom without having to take a break and catch his breath :( - So with zero income coming in, my needs are met, but I don't have the luxury buying things that aren't a necessity :/ ) So anyway, I would do the narration if you want a native English speaker for the ad (I have a pretty nice microphone and I went to technical school for sound production, so I know how to use a really large professional recording studio, so I'm sure I could figure out how to do a video narration lol :D ) ... I don't expect you to want me to do it, but UI wanted to put the offe3r out there just in case. I just wanna do whatever I can to help your channel grow and make it continue to be as awesome as it already is, IF NOT MORE AWESOMEERRRRRR!!!!!!! lmao I hope this all works out... IF you're looking to get some new toys... err I mean new TOOLS lol ;) Let me know if I can help in any way :D

Attach a Sumitomo cyclo drive

Co to za przekladnia z czego?

Przekładnia całkiem dosłownie zjadła zęby na robocie😂

I would set your welding machine a little higher from now on, your welds are just a little too convex and probably not properly burned

Cos te rebaki Cie nie lubia. Ktorys z kolei i znow cos nie tak. Ale jak juz udoskonalisz projekt to będzie na lata

Делать хрень ради видоса... Ну так себе идея! Думаю 250 полуляхов из 250 возможных! Приваривать ножи - не комильфо!

too many torq-u's

You still did a great job. Not on you.😡😠🤬gearbox

Since this failed it could end up being a blessing with a little imagination. I'd experiment with various worm gears from different tools/machinery, or chain/belt drive etc. Btw, I'd rather watch one of your rare "fail" videos than most success videos from other channels. I hope you don't give up on this just yet. God bless. [edit]: Here in the U.S. certain marketplaces have a "free" section with old broken tools/machinery to use for parts.

Nice sharing Vidio.. very inspiring and useful.. great ❤😮

Tak czasem bywa, że nie wszystko po naszej myśli idzie. Złośliwość rzeczy martwych jak to mówią. Ale dzięki, że dzielisz się z nami filmami z budowy swoich urządzeń. Doskonale wiem ile stworzenie takiej maszyny zajmuje czasu, a później montaż filmu. Dla nas to 40minut ogladania dla Ciebie kilka dni lub tygodni budowy. Chylę czoła za pomysłowość i wytrwałość w tym co robisz. 👍

I think a dual chain reduction drive: main shaft to an idler shaft, then back to main shaft with sprockets and chains; fairly inexpensive and robust, and will fit into the same space. Two ten to ones gives 100, and first is 360 rpm, and second is 36 rpm. Pro Tip: don't get your fingers caught in that 🙂

The only fault in my opinion is that the blades are welded. There is no possibility of replacing the knives or removing them for sharpening.

the gears arent misaligned. its a harmonic drive. the issue is that it once had water in it and rusted. someone cleaned up the rust. the teeth look chewed up. maybe a piece of metal got in there and mangled them all up. or perhaps it was wrongly reassembled cause it had more slop in it after the cleanup

단순한 나무 조각이 아니라 프라스틱 나가서 약한 철도 파세하는 기계을 만들어 보세요 상세한내용 감사드림니다~^^

Cycloidal drive gearbox

Co za typ reduktora Jaki moduł mają zęby Ile razy prędkość z silnika zmiejszona na wyjściu z reduktora Pozdrawiam

Przekładnia pewnie już była uszkodzona... Dostała większego obciążenia i pokazała dlaczego ktoś się jej pozbył... Pozdrawiam 👍👍 fajny projekt

1.Ten typ przekładni to nie jest przekładnia planetarna. 2. Na drugim końcu wału z ostrzami powinieneś dać koło zamachowe, wtedy obciążenie przekładni miałoby mniej udarowy charakter. 3. takie sprzęgło jakie dałeś pomiędzy silnikiem a przekładnią (tylko odpowiednio większe) powinno być pomiędzy przekładnią a wałem z ostrzami - również niwelowałoby udarowy charakter obciążenia przekładni, co na pewno przełożyło by się na jej żywotność. Pozdrawiam.

Worm gear isbmuch more sturdy, but great build bro!

How about the exhaust fumes from the engine? Do they become sent away to the max? Otherwise I would think of headaches if working too long with it, in particular outsides at days without any wind going. Great build! Can't await the next episode! Greatings from Bitburg, Eifel, Germany, long live the EU! 🤗👏 (How about installing hardened cutting edges to the blades?)

Well, sometimes things doesn't go as planned, but that's what makes life interesting. Get up on the horse again guys, you got this! ☺🙏👍

One thing i don't get is... why are you complicating your life with this design? It's not the smartest. The flywheel type with the blades placed (like spokes) results in a finer chip and it's also easir on the engine, since the flywheel soaks up the impact AND the smaller cut = less power loss. IMHO, you should try that. Just get a large off-cut from your source, cut two slots in it, angled so that the knives can be bolted in, add a shaft driven by belt (even more engine protection) and make a housing with a chute that puts the branch at the knives, at an angle. Just my 2 cents, the "water wheel" design is not good. I've seen so many of the commercial ones fail after a while, broken mounts from vibration, burnt out electric motors, and all sorts of complaints - and that's on top of the less efficient design. As always, your building skills, top notch, so the above is not a critique of that. Just that i don't think this design is viable.

It's a little scary how talented you are, I like your vids!

It's asking a lot out of a gearbox. Needs something to slip back in the old days they used to use leather discs

Super pomysł i wykonanie, wymienisz Darek przekładnie i będzie chodzić. Pozdrowionka

See if you can find at least a four gear planetary gear setup and try again...

Oh well nice try. At first wasn't sure what it was meant to be, then saw the "blades" being shaped. Would have done so blades were adjustable as on forage shute. But good idea, until g/box broke. Nothing you did caused problem, just bad adjustment/alignment at factory. Thanks for showing, love your work, some very interesting projects you have done. Best wishes from UK.

yes, this type of gearbox is not suitable.

Are those the Fireball Tools magnetic shims?

Użyj przekładni planetarnej

david west youtube channel

U need any types bearing just ask me please

Please do some safety guards!!!!

Przekładnia była za słaba i nie wytrzymała czy już wczesniej była uszkodzona?

That great your handy build I do like it 😊

Nice machine 👍

It wasn't essential here, but I wonder what made you decide to use a gasoline engine instead of an electric motor?

I'm happy that it's stopped honestly this thing is seriously dangerous wish all the best and safe

مادام المشروع فشل ماذا استفدنا من مشاهدته سوى انك أخطأت في اختيار الجير بوكس المناسب لهذا الجهد

Chia sẻ cách làm rất là tuyệt vời 🎉

people are suggesting worm gear. I like worm gear and use one in a much lower torque application now. But one large enough for this must be very expensive. To make one on your own has challenges. For one, my understanding is it is not as simple as a screw, because there is pitch involved. Also, it changes the orientation of the machine to 90 degrees at the shaft rather than straight. I suppose you could use two smaller worm gears, though, to get it back in line with the engine shaft. This might be a good idea since two half sized worm gears is likely cheaper than a full sized one. Whatever you do to get this machine going, worm gear, new planetary gear box, or something different, Im sure I will enjoy watching it 😊

Thanks for the video. It’s always helpful to see what works and what doesn’t. I wonder if some kind of hydraulic drive would be more resilient for this kind of work where the drive might jam?

That is , as always , a very interesting project ! Shame for the reduction gearbox getting destroyed BUT some of your most intriguing videos are about modifying / improving existing projects or getting out of dead end ideas with success !

I'm not disappointed I still learned something. Like someone said it was a bad gearbox but can you fix it or is it unrepairable? I don't know you the man thanks!

I think you may want to make a slot instead of a flat plate where the wood can fall straight down just after it cuts so it can't get pinched in the chute as the cut piece is forced out the back. If you have a slot it gets cut and falls straight down and away from the cutter each time. I saw a few pieces go sideways and get cut a second time part way. Great job. Enjoyed watching the build.

Not approved for safety. To avoid possible dangers, it must have a protective cover so that the blades are at least 12 cm behind the cover.

Is it a cycloidal gear box?

was very nice, get a sizing gauge before next test run & me I'm digging garlic NICE work

Як називаеться монтажна пила по металу якою ви користуетесь ?

Too bad that gearbox broke, hope you find another one that works or change the design to handle a different one. Good luck 👍💪✌

As long as you learn something from it, not a fail, the gearbox on otherhand is full of sparkly oil 😅

Mam pytanie jeśli dobrze pamiętam Hinomoto zdejmował jakąś pompę do sprężarki ?czyżby jakiś projekt większej sprężarki do piaskowania może napędzana wałkiem wom ?

Probably just slipped on the key or key is worn. Cheers.

How can that be a failure? Your rotary welding table worked perfectly 😂

sharpening the blades will be an interesting chore.

gearbox from toy-story shop..............

Time to hunt down a tougher gearbox!

A new gearbox and it's good as new.

👍

MM77 Approved 👍🏻 👍🏻

so @ 6:16 is that a new saw??? VERY NICE!!!!! I hope you get a TON of great use out of it :D

part 2 it will work