Can't get an industrial floor sander? No problem! I show you how to refinish your hardwood floors using a belt sander and an orbital sander. #HardwoodFloorRefinish #翻新实木地板
A square that size takes about an hour. If you keep putting on fresh belts the job goes faster. 36 grit for the first pass is good: it will eat the old finish fast, but it will leave some rough texture to sand out with finer grits. I used 50 and 120 for this floor. Good luck!
The speed of sanding depends on how much old finish is on the floor, the type of finish, the species of wood, and how scratched and dented the wood is. The floor in this video did take an hour per 10x10 square.
Now if I could just find a video showing how to do this with five animals lurking about the house. LOL. My floors need some love but two rooms I want to do don't have doors to keep the cats out - you know, the creatures that are absolutely invisible in the far corners of the house till you paint or varnish and then BAM, there they are.
i've got a relatively small room with some really rough flooring but it's on a 4th floor walkup and i'm super tempted to use my belt sander. but if i do, i think i better use an aluminum profile to keep myself level. I guess if i take my time and don't dig holes it should be alright. lucky i have knee pads.
I went though about 10 belts of each grit. I used a regular paint roller, and I used oil based varnish for this floor. If you use water based polyurethane, I suggest looking up other tutorials for the best form of application in your case, since it tends to get full of bubbles using regular rolling techniques.
@@MooseMultimedia thanks...I'll be using a stain and oil based poly. What size roller do you recommend for the poly? And how do you recommend I apply the stain? Thanks again
@@josepe2448 I used a standard sized paint roller for the floor, the same size people use for rolling paint onto walls. This video explains staining far better than I could in writing, and is one of the methods I often use: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-MtqZIB6R2EE.html
@MooseMultimedia hi I understand that but there are different sizes meaning the thickness of the roller. Some rollers are meant for smooth surfaces, the slightly thicker ones are for walls that are a little rougher etc.
@@josepe2448 I honestly don't worry too much about the nap. If you use water based paints the heavier nap tends to give the paint more of a textured look because it dries fast, thereby preserving the texture. Oil based dries slow and has a chance to level out before it dries. The main concern with using a heavy nap and oil paint is that the roller will lay it on thick if you don't spread it around enough, which can cause a wrinkled effect as it dries. If you want to lean on the side of safety, go for a light nap. I would suggest experimenting on a scrap piece of wood before attempting the floor so that you get the desired look.
It looks good, but they rent floor Sanders that would make the sanding a 40 minute job besides the very edges of the floor. I mean this would definitely work, but it's worth just renting the big ones.
Yes you can, but you might want to use an orbital sander afterward to get the belt scratches out. Always test your methods on a scrap piece before committing to your project.
That method will even out some warping between the boards and leave a flatter floor. You will also have to sand more to make the floor look uniform and to get the sanding scratches out. Try it on some scrap wood before committing to doing the floor.
The can will say how many square feet it is good for. The first coat will suck up more finish than subsequent coats. I always buy more than I need so I don't run out. I think I used 2 gallons for around 600 square feet.
@@edisonmandap6185 If you use oil varnish the wood color will darken toward a golden color. If you use water based clear coat the color will change less. Matte or gloss will look equally good depending on your tastes. I would test it out on a scrap piece first so you are sure of the results.
@@Jontyfarmer You honestly have no clue how to sand a floor proper for refinishing or you wouldn't stand behind this. What a joke. Post your work or carry your ass.
How about appreciating the fact that he did the job, that he improved it immensely, and that HE is happy with it. I'm sure i could find fault with everything you do too.