Тёмный

Remove the GM PO1 P59 PCM VATS and MORE for FREE Using Your PC LS Swap Engine Management System 

Laurenceville Garage
Подписаться 9 тыс.
Просмотров 1,5 тыс.
50% 1

In this Part 2 video I show how I connected a stock LS pcm to my pc with the harness I just made. Then, use my pc and some free programs (PCM Hammer and Universal Patcher) to delete the VATS, Delete the rear O2 sensors and tweak the temp the dual fans will activeate. I would still recommend a professional tune before running on the street, but you can do this basic work to allow you to test run your engine and get you going. Thank you for watching!
Having an engine test run stand is a great idea, however the key word is "run". In order to get an LS engine to run on a stand or anywhere else means the pcm needs to be tweaked to start and run (unless you go carb). So if you only have one pcm to delete the VATS from, you could just contact any number of "tuners" in your area to perform this task...usually at a cost of $100-200. IF you have more than 1 pcm to work on then maybe you should consider a way to do this yourself and save a ton of Benjamins! In my previous video (Part 1), I showed how I built a bench top harness to connect your pcm to your pc. Cost could easily be under $100. Don't let it intimidate you, try it!
WE GOT SOME LAURENCEVILLE GARAGE SWAG AND DECALS!!
Check it out with this link....
saydesignsllc....
I'll list the parts I used in case you have not seen the harness build video (you may already have your own):
Amazon:
www.amazon.com...
1) DC12V 2A Power Supply Adapter, SANSUN AC100-240V to DC12V Transformers, Switching Power Supply for 12V LED Strip Lights, 12 Volt 2 Amp Power Adaptor, 2.1mm X 5.5mm US Plug (1pcs)
$7.98 amzn.to/43tQKJX
2) LeMotech Project Box ABS Plastic Junction Box IP65 Waterproof Electrical Boxes Universal Enclosure Black 6.2X 3.5X 2.4 inch (158x90x60mm)(Pack of 1) $7.38 amzn.to/43yHfJB
3) QTEATAK KCD1 On/Off 3-Pin 2-Position Snap 10A/125V, 6A/250V Red LED Boat Rocker Switch-5Pack Pre-Wired $7.99 amzn.to/4cxOKUY
OBDX:
OBDX Pro VX - OBD2 Diagnostics and Tuning - Ship From United States $80 + tx
obdxpro.com/pr...
Ebay:
PCM Connector cores Green Blue LS1 LS6 LQ4 LQ9 LM7 4.8 5.3 5.7 6.0 ECM P59 LSx $17
www.ebay.com/i...
Mouser Electronics:
OBD2 Port Plastic Connector, 16 Pin 829-12110250 1
Terminals - for OBD2 port 829-12129373 4
Terminal Lock - secures terminals 829-12160437 2
I forget cost, but under $10
As always, if you have any thoughts, suggestions or comments, leave them for me in the comment section. I read all of them.
All information provided is for "entertainment purposes" only. If in doubt of your skills and abilities, please consult an automotive professional that can help you. I am sure there are multiple ways to produce the same results, this is how I did it. Please note that links to amazon allow me to make a small (and I do mean small) commission on any sales. It does not add extra $ to the price of the product. Thank you.
You can contact us at:
Email: laurencevillegarage@yahoo.com
Follow us on FB at laurencevillegarage
www.amazon.com...

Опубликовано:

 

15 сен 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 6   
@dsmmonster
@dsmmonster 3 месяца назад
Thanks for the video it was very well explained..!!
@laurencevillegarage
@laurencevillegarage 3 месяца назад
Glad it was helpful!
@gregjohnston1781
@gregjohnston1781 5 месяцев назад
Why would you want to disable the rear O2 sensors? Super video. Thanks, and it is done with free software, awesome.
@laurencevillegarage
@laurencevillegarage 5 месяцев назад
If you were swapping a motor into an emissions exempt vehicle, hot rod, race car, etc. and were modifying the exhaust or engine itself you can delete the rear sensors. If your exhaust has no catalytic converters, no need for the rear sensors. Then you would only need the front sensors to tune.
@WELDERUPGARAGE
@WELDERUPGARAGE 26 дней назад
Can you do this to my PCM? It’s a 2000 Silverado 1500 4 x 4 4.8 L 4L 60 E Is it possible using PCM hammer to change shift points? I’d like my transmission to shift a few hundred RPM later than stock. Love your video very easy to follow I have a hard time following some of the other videos that are out there so I really appreciate what you put together
@laurencevillegarage
@laurencevillegarage 25 дней назад
While I am able to remove the VATS and rear O2 sensors, that's where I draw the line. I am not familiar with the finer details of the tune like you want. I would suggest a tuner that can ride in your truck with you and dial it in exactly the way you want. It will be more expensive, but will give you more of what you want. Thanks for the opportunity.
Далее
Remove VATS for Free using TunerPro and PCM Hammer
27:01
Forget TunerPro. Use This Instead.
22:30
Просмотров 30 тыс.
DIY GM LS Bench Harness for PCM stuff
18:56
Просмотров 8 тыс.
Install AC on my LS Swapped OBS Part 1
16:45
Просмотров 2,4 тыс.
Using the OBDX Pro VT with PCM Hammer
10:27
Просмотров 4,8 тыс.
LS Swap Stock Pcm Bench harness | DIY
19:17
Просмотров 10 тыс.