Repairing damaged or lifted pads on a circuit board

Подписаться 58 тыс.

Просмотров 379 тыс.

50% 1

When replacing components on a circuit board, sometimes you may accidentally remove or damage the pads used to hold that component in place. Here are a few helpful tips for providing strong, long-lasting repairs for damaged or missing pads.
#soldering #electronics #tutorial
T-SHIRTS
Do you like my wacky t-shirts? I buy all of them from Qwertee. Use the discount code: BranchusCreations to get £1/€1/$1 off your order. Check out the range here:
bit.ly/3OrJZkT
If you enjoy the content and would like to support the channel, please consider becoming a Patron:
/ branchuscreations
Of if would like to make a small donation, you can do so here:
www.paypal.me/...
Tools/Products used (paid links):
SOLDERING IRON
Hakko FX951: amzn.to/31QvCMW
SOLDERING IRON TIPS:
Bevelled edge soldering iron tip (T12-BC2): amzn.to/45NSrBK
Small bevelled soldering iron tip (T12-C1): amzn.to/3YVH5K0
Bent conical soldering iron tip (T12-JL02): amzn.to/3sx8lSU
Chiselled soldering iron tip (T12-KU): amzn.to/44tAo2A
HOT AIR STATION:
Quick 861DW: amzn.to/2ZjYzPH
SOLDER:
Kester 63/37 0.5mm diameter: amzn.to/3uviEIg
FLUX:
StirriASM: amzn.to/43nT05e
SOLDER WICK:
Goot Wick 2mm: amzn.to/3YWlRvw
TWEEZERS:
Hakko CHP 3-SA: amzn.to/2NqkhPz
DT71 DIGITAL MULTIMETER TWEEZERS:
amzn.to/41VcvSb
OTHER:
Vevor 30L Ultrasonic Cleaner (5% off on all Vevor sites code: VVMH5%OFF):
AU site: s.vevor.com/bf...
US site: s.vevor.com/bf...
EU site: s.vevor.com/bf...
-----------------------------------------------------
Component suction tool (vacuum pen): amzn.to/44xyPkm
Microscope: amzn.to/2HnSI5H
Microscope camera: amzn.to/2TdSYsZ
Budget alternative microscope: amzn.to/2PmRagt
Budget alternative soldering station (uses T12 tips): amzn.to/2SeUpHg
Budget alternative hot air rework: amzn.to/3fN1ZU7
Helping hands (third hand): amzn.to/31JUhVL
Ultrasonic cleaning fluid: amzn.to/2YusoQQ
Fume extractor: amzn.to/2HuG0oU
UV Solder mask: amzn.to/2ZnK1yu
Swann Morton curved scalpel blades: amzn.to/2oN7qNn
No. 3 Scalpel Handle: amzn.to/2ngcx85
Kapton heat resistant tape: amzn.to/2xBnTso
28 AWG enamelled magnet wire (thick): amzn.to/32cRsLf
34 AWG enamelled magnet wire (med): amzn.to/35Bx20D
40 AWG enamelled magnet wire (thin): amzn.to/2J2Aisf

Опубликовано:

26 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 420

@evanparent07 3 года назад

The Bob Ross of Circuit Boards. I'm so relaxed and feel like I can accomplish anything!

@normallife3819 2 года назад

One of these types of things fell off of the back plate of my GPU a p106-100 6gb compute only GPU.

@Daaannn 2 года назад

I fell asleep watching this :( so relaxing....

@keithking1985 Год назад

Agreed I just found this channel this minute and you hit the nail right on the head there..

@oiooiioioiooioii5400 Год назад

This reply is perfect, it's true.

@atetraxx 9 месяцев назад

This dude rules

@aaronbraun8675 3 года назад

My cat and I were EXTREMELY confused by that whistling. Subscribed.

@43audio89 3 года назад

Im certain he lives in a jungle of sorts lol

@daedelus_ 3 года назад

Same. After a few times I was wondering if it was outside and what bird it was, or if it was in the recording.

@PeterWooley Год назад

This was a tremendous help. I got the info I needed within the first few minutes and then just kept watching the rest of the video while I made my own repairs. Helpful and relaxing!

@bobbaxter952 10 месяцев назад

I've just destroyed a couple of little 8 legged eeprom pads,they are tiny.This has given me the idea that you really dont have to replace the actual pad,just as long as you make the connection! Which has given me a little more confidence. I thought i would have to glue on little pads to the board for the eeprom legs then solder!

@dustinalexander1829 3 года назад

Thanks for this. Really helped me fix my 3 year old daughter's toy that grandma and grandpa bought her. Now it's time to buy good solder, an iron that doesn't come from wal mart, and more flux. Learned that from another of your videos

@brianfox7067 2 года назад

Pro tip, don't drink red bull and take adhd pills for at least 8 hours before trying to hold on to 36awg with tweezers under a microscope

@BranchusCreations 2 года назад

I'll keep that in mind!

@jaggerneill1404 4 месяца назад

Nah this is so real I can’t do any delicate task soldering for at least 2-3 hours after I drink coffee under the scope it looks like I got Parkinson’s 😅

@stephensmith735 4 года назад

I was delighted to come across this as I was struggling with damaged CF pinout pads. Wonderfully clearly presented. A great teacher. Thank you.

@micarifamily1 3 года назад

I really appreciate your attention to detail with following traces and pads and making things look as nice as possible, not many people do that. It peavs me to see sloppy work done. Thank you!!

@micarifamily1 3 года назад

@@lfino100 yes went and signed up we will see and thank you for the info!

@Galaga_ 4 года назад

I have been trying to repair a hard drive for months and had to change the rom chip from the original pcb to a donor pcb for it to work, while doing so I damaged 3 of the 8 pads on the pcb I had to install the rom chip, when that happened I tought that was it, that I lost that hard drive for good. Thanks to your video I could repair it and right now im backing up all the data. Thank you so much, I suscribed to your channel, you are awesome!

@elimerrodriguez374 4 года назад

I'm not sure but ,if anyone else wants to discover electronics repair course try Saankramer Electronic Magazine System ( search on google ) ? Ive heard some interesting things about it and my colleague got excellent results with it.

@SueDohman 3 года назад

This was very helpful, indeed. I equally appreciated your polite conversational demeanor, albeit, one way. 👌🏻

@marinehm 3 года назад

Still watching some of your other tutorials. Now I feel stupid. I never thought to use solder wick to pull solder out of a soldering point (hole). I've always used a solder sucker which does a crappy job. You made it look so easy and it came out very clean. Ordering fresh solder wick.....

@linarachdi7544 3 года назад

This was great, thanks, I been tryin to find out about "how to find a hot leg on a circuit board" for a while now, and I think this has helped. Ever heard of - Giyathan Bewildering Gratification - (Have a quick look on google cant remember the place now ) ? It is an awesome exclusive product for discovering how to repair your electronic items like a wizard without the headache. Ive heard some unbelievable things about it and my mate got great success with it.

@marinehm 3 года назад

Oh, hell yeah! It works like a charm! Thanks!

@surenbono6063 4 года назад

...very rare repair tips...thanks to the internet and you..a sound mind is critical for this jobs...frustrations is not an option..

@phon-er 3 года назад

Great video. Learned so much from it. Amazing tips and tricks and knowledge in general about traces. I have a messed up pads under an ic chip and I wasn't sure where to connect them if their trace point was right next to them haha being confused from the openboard of where it connects to, I assumed i needed to connect the jumper wire there but I reckoned that all I had to do was connect to its trace point and thats all, thanks to you. appreciate it mate.

@donaldhunt4 3 года назад

This is now my favorite channel! Thank you!

@kayathepiratebaykid 3 года назад

Thanks. Very nice instructional video. I like how good you communicate, keep it funny, and very informative. One of the best channels I have come across in a while now. Keep it up

@damianreilly2900 3 года назад

.........and the Koel in the background loved the video too!

@daveflatters4981 2 года назад

I’ve really enjoyed watching you repair the pads and traces in two of your videos, but the thing I’ve enjoyed most is that you call what you are doing soldering not soddering 😂😂

@Frozirra 4 года назад

Dude thank you so much! I am a beginner, and I wasn’t initially using as much flux as was necessary, and this has helped me salvage some earlier diy projects I fucked up

@pr0xZen 4 года назад

Good flux makes a word of difference. I'vr personally found that the flux core in solder lead just vaporizes too quickly for most jobs, at least rework and things with a bit of thermal mass. Just remember: Use ventilation. Fume extractor is king, but at minimum a fan to blow the fumes away from you. Flux fumes are hazardous as hell. And - remember to clean off the flux afterwards, unless it's truly no-clean type, and that you _know_ it comes from the original manufacturer. If eg. a 10cc tube of the very popular Amtech 559 flux costs $2-7, it's fake. Original is more than twice that, straight from Amtech. *_Most_* of the cheap flux you can get on the internet (like Amtech 599), is fake stuff. Only on _very_ rare occations, you might get genuine but out-of-date stuff. Some of the fake stuff does a very decent job as a flux while soldering - but you have no idea how it will behave if left on the board long term. Some of ir can be corrosive. All of it will be tacky (which can become a serious problem if it's an actively cooled device, as it'll collect and trap huge amounts of dust and other crud from the air cirulating through it. And dust is commonly conductive.). Only leave flux on the board if you know it will behave according to the original manufacturer spec (and those properties are ok with your particular project).

@jjcale2288 4 года назад

@@josefinasolorzano3784 SPAM

@jjcale2288 4 года назад

@@jenniferrey4787 SPAM

@alejandrobreceda8509 2 месяца назад

THANK YOU!! Super useful information and very clearly shown. Inspired to go back to some boards I've just given up on!

@ermdon 3 года назад

I love how you tought this. Thank you so much !

@goncalodumas 5 лет назад

Just last Friday I managed to partially rip two pads on a colour classic analog board while removing capacitors. This video was god sent! Thanks.

@goncalodumas 4 года назад

Sorry, logic board, the pads were from a logic board. By the way, is there any method to glue a new pad to the board? So to better fix an smd capacitor. Then one could link to the via using the enameled wire.

@Promethium666 3 месяца назад

Im a service technician for a company that deals with flue gas analysers and trace repair has now become a part of my duties when i have zero experience with it naturally, so i really appreciate your very informative video listing tools and for showing your very professional methods, thank you very much good sir.

@manojithalder7448 3 года назад

Learn lots of new things. Thank you sir for showing us your amazing skills.

@rodzent 10 месяцев назад

Super video. Very high quality cameras. Nice you have the microscope to show clearly what you are doing.

@wertherellerbrock 3 года назад

Fantastic! Some very good tips! Very helpful, informative, and with very good camera shots. I like the manner in which you present the information. Thank you so much!

@randywetzler5976 4 года назад

Excellent video, thanks for sharing! You gave the confidence to repair a small flight controller board with a torn off pad, small diode, using your angle method. It worked!

@fatbetrn1976 4 года назад

My electric shaver broke because it has a contact pad switch and the pads were corroded. Cleaned the pads. Put some solder on there, tried to level it out as much as possible. Now it works again.

@johnsmallberries3476 6 месяцев назад

Thanks for providing links for all your gear...I wish more guys would do that 👍

@KP11520 3 года назад

That really was a GREAT real life and road tested approach that we would take years to amass ourselves! Down and dirty! LOL Not a criticism. Rather a compliment! Thanks Mate! So glad I added this to my mental data base. I was actually looking on how to repair round pads where heat from components through the holes lifted them off the board. Maybe copper tape and high temp epoxy and soldering to exposed traces? You'd be a great teacher for those techniques as well if you are looking for another show and tell! Thanks again! Cheers!

@daz41262010 Год назад

so glad I found your channel the tips and tricks for board repairing traces and tracks is amazing :)

@MountBaldyBrewing 4 года назад

Thanks for explaining that in such detail. I've soldered things for years and just wing it on most things. When I was repairing a subwoofer recently, I pulled pulled up a trace connecting one of the capacitors I was replacing to the board. This saved my bacon. I was worried I had ruined the board.

@kennykenaz8340 4 года назад

Lovely Video clip! Apologies for chiming in, I would love your thoughts. Have you heard the talk about - Tarbbatigan clean errors Tip (Have a quick look on google cant remember the place now)? It is a great one off guide for discovering how to fix electronic devices minus the normal expense. Ive heard some unbelievable things about it and my friend Sam at very last got cool success with it.

@PeterStap-h3l 2 месяца назад

Very impressive Bruce. I’m a fan!

@dido1803 3 года назад

I enjoyed seeing your video. You explained well. Lovely bird singing in background.

@josip1881 3 года назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-eCFrRsBCKHc.html, red eyed bird xD

@dido1803 3 года назад

@@josip1881 thanks for the video of the bird. Now I know the mysterious bird.

@Moshugaani 3 года назад

Thanks so much for this lesson! I though for sure that a device was a gonner since it had two pads ripped out. But I'm still not sure if I am skilled enough to repair. Well, it'll be an interesting learning experience at the very least. :D

@JanZrimec 4 года назад

Great clear video that put me in the right mindset to quickly fix my broken pad problem, thanks!

@BranchusCreations 4 года назад

That's great to hear!

@reminon Год назад

It's so sad that your sub count is low. This is repair gold! These videos have raised my confidence in trace repair.

@antlu65 2 года назад

Before watching this video, i tried to repair an smd cap, both pads missing, by using solder wick for the conductor and solder to hold it directly to the traces. Really ugly and falls apart if I gently bump it by accident with a finger - just a mess. Glad I watched this vid, now I can try doing it properly.

@Phoenix_1982_MD 3 года назад

Great video, I wish I had this Infos as I broken my amstrad 6128 and threw it away afterways :) thanks for that, another food lesson learned!

@wiggindorfthemagnificent 10 месяцев назад

Thank you so much! You saved my drawing tablet! It lives again!

@toyotatacoma6817 8 месяцев назад

Great Video! I have a similar issue, the pads are gone but have no holes to solder a wire into, and the only thing left is a thin trace to where the pads were... I'm going to try a combination of your trace repair with your pad repair and hope for the best. Thanks for the video!

@cidhighwind68 3 года назад

Excellent video, tons of great tips & advice!

@stephenbrighouse7598 Год назад

Hi Bruce I'm in England and I've took up electronic as my hobby I'm a big fan of your channel great video s mte

@thmsnhl Год назад

Thanks so much for sharing these insights, you just saved me 50€ for a replacement board! ❤️

@keithnoneya 10 месяцев назад

I think this video is more on how to avoid or bypass repairing pads and runs using short cuts on how to get your equipment to work. I have to give you Props on originality at time index 12:49 putting the component slightly sideways, however this is not a professional way on how to do it. There was enough pad area to overlap a new pad, glue it done or even use an Eyelet to anchor it, even a wire would work. I know that running a business you have to take short cuts to get the job done, get it to work and out the door, so that's why I thought your approach was economically acceptable just not professional. Retired Avionics & Avionics Test Set Technician of 42 years & formerly Certified Solder Technician of several years. Still I enjoyed the video. Best Wishes & Blessings. Keith Noneya

@kennydee5856 4 года назад

Great video! It sure helped me fix a microphone board that I thought was doomed w a lifted pad.

@natasaceko9615 4 года назад

interesting points ,if anyone else is searching for electronic repair service try Saankramer Electronic Magazine System (should be on google have a look ) ? Ive heard some super things about it and my friend got cool success with it.

@segasonic9117 4 года назад

All those missing and eaten pads! Reminds me of the original PC Engine DUO! One I bought was like this. After watching this video, I may go back and try to repair it! Fantastic video!

@clai889 3 года назад

this is a very great tutorial for person like me wrongly remove the pad from pcb thanks a lot

@davidburlingame2421 2 года назад

Excellent video, brilliantly explained. Thanks for sharing.

@evanbates1212 2 месяца назад

Very helpful information. Well done!

@CucumbersSC 3 года назад

Thanks for the very useful video (esp for clumsy fools with too-hot irons like me) and shoutout to the very atmospheric birdsong in the background!

@brannenthompson9662 4 года назад

Its the wildlife in the background that was thinking I was drinking too much, lol.great info.

@vsat88 4 года назад

I thought a new species of animal had moved in. I had to keep stopping the video and listening. Could not tell if it was outside my house or on the video for a while there !

@gustavocastroortiz7645 4 года назад

I'm not sure but ,if anyone else wants to learn about laptop repair try Saankramer Electronic Magazine System (do a google search ) ? Ive heard some extraordinary things about it and my brother in law got excellent results with it.

@marceloalfonso7130 4 года назад

Not certain about the points made but ,if anyone else wants to learn about how to repair electronics devices try Saankramer Electronic Magazine System ( search on google ) ? Ive heard some unbelievable things about it and my cousin got great results with it.

@stevehead365 4 года назад

I think that's his Tui assistant

@leglessinoz 4 года назад

Sounded like a curlew

@stormtrooperelite1453 4 года назад

word of advice for anyone making own pcbs, make the pads much bigger that the component contacts, it will make your life much easier

@PabloPazosGutierrez 3 года назад

If you were an university, I'd like to study there! Your videos are awesome.

@emmettturner9452 4 года назад

Radio Shack used to sell a "Pre-tinned wire" (278-1341) that I used for similar repairs. It works great through vias since it will flow solder right through and never had an enamel coating in the first place. If you're the type to save component leg trimmings for making jumpers, it's a bit like having a 50ft spool of component leg! At around 17 minutes you trimmed the excess wire on one side when you still had work to do on the other. I suggest leaving that extra length there until you have the other end secured. As you demonstrated earlier in the video, a short little wire like this will often reflow existing solder while you are working on the other side. This can cause difficulties if you are making a particularly short and precarious jumper. The extra length at the other end gives it more thermal mass and makes solder less likely to unintentionally reflow at the other side.

@BranchusCreations 4 года назад

I tend to do the repairs as I see them, and I don't always necessarily do them the same each time. And I do (regularly) look back at some repairs and think "I would have been better off doing that one a different way", but that's just part of the fun!

@robbirobson7330 4 года назад

if you want to repair the pads and you have some donor boards around sometimes you can try and cut some pads of with the trace on it and then stick it on the broken pad, i use to do that if its a smd ic where sometimes you cannot solder a wire because of the space

@paddlerpaul2577 3 года назад

Thank you I learned loads from that video. Paul

@Juxtapose1984 4 года назад

Very helpful and you make it look easy. Nice, clear, in-close camera work as well.

@alexander0194 2 года назад

Great video. Thanks so much!

@sires8765 4 года назад

Someone who actually shows real close ups

@codebeat4192 4 года назад

Nice video, nice chap. I would suggest to not use wire with enamel at short reroutings, use normal (naked) wire instead (stripped from a cable or such), only use it when you have to. I would suggest to clean the wire first with a knife to be sure the copper is fully exposed. The problem of wire with enamel is that you need to be sure it is burned away completely and you need to provide more heat to do this. When it is covered by solder, you are unable to see what is going on under the solder, there may be contaminants or a (sticky) cold solder joint. To avoid this, clean the wire first, it is better to clean it first to be sure there is always a good connection in the smallest period of time to heat/stress other pads, tracks or components. Tip: When you are in need of wire with enamel, try to reuse coils from a spare board. It is cheap, plenty available and evironment friendly. ;-)

@arnolduk123 4 года назад

Yes, I agree that NOT ALL enamel wire is good for melting and leaves oxidation residue with poor solder joints. BUT he may be using an enamal wire that is made for the purpose of melting and tinning. By the smell he points out, I don't think it is. Myself, I prefer uninsulated solid copper wire for short runs and wire from old network/telephone cables for long runs. Another method for sourcing and wiring thin component tracks is to use a few strands of copper wire from your solder braid. Just unravel the strands to length required. Solder braid is a tinning wonder wire! And has more uses that just mopping up solder. Still, this was another great video which I will refer to all the time to refresh my repairing methods. SUBSCRIBED!

@andytrewin Год назад

excellent video Bruce - interesting bird call in the background. KR AndyT(UK)

@BranchusCreations Год назад

If I remember rightly, the bird call is from an Eastern Koel.

@suadcokljat1045 4 года назад

Good work. Thanks.

@QuintinMassey 4 года назад

At 10:54 did that solder come out so easily because of the flux?! Also, the amount of flux he applies is equivalent to the amount of olive oil Chef Ramsay uses to cook 😂😂

@BranchusCreations 4 года назад

Getting solder out of a hole is sometimes super easy, and sometimes it's a nightmare, though the flux certainly does help. For the really stubborn ones I usually add some fresh solder to the hole. It sounds counterintuitive to add solder first when you want to remove it, but it usually works.

@richardwatkins6725 4 года назад

thanks for doing such a brilliant video and great tips

@lukassatkauskas2179 Год назад

U just saved my day big big thanks keep going!!

@izzzzzz6 10 месяцев назад

I can never get the enamel off of the magnet wire, i resort to burning it with a lighter or scraping it with a scalpel or sandpaper. Copper tape is another good trick and a bag full of different sized via's. How hot do you set your iron to melt the enamel? I think need to move to thinner wire, will recover from speaker coils and old transformers.

@BranchusCreations 10 месяцев назад

On the thinner wires, the enamel comes off really easily. I have my iron an about 400ºC.

@jjcale2288 4 года назад

Beautiful work! I watched your video with delight 👍

@elhatillanodigital5011 4 года назад

Hi, I have used stained glass copper foil, cut it carefully and as it has a thermal activated glue, I fix it to place and then solder the component.

@duroxkilo 3 года назад

that sounds like a great idea

@jackevans2386 4 года назад

Best practice dictates that you would always make sure your enamel wire, or any type of wire is pre-tinned before any soldering is performed. This ensures the least amount of time required to solder the component, thus reducing the amount of time heat is applied to both component and PCB. It also reduces the amount of gunk created due to the enamel being burnt off while you're trying to solder. The cleaner everything is up front, the faster the soldering process gets done and the least amount of heat needs to be applied. But they obviously do things differently in Crocodile Dundee land. Cheers from NZ

@BranchusCreations 4 года назад

Mine is not necessarily the right way, just the way that works for me.

@vincentmitchell774 3 года назад

Very nice. I need a few hundred hours of practice before I get that steady.

@pr0xZen 4 года назад

Regarding the "stubborn hole". What's really going on there? Is it lead-free original solder, not "diluted" properly with leaded, and then the braid soaks up the leaded solder too fast before enough heat can be transfer to melt the (still mostl lead-free solder underneath?

@BranchusCreations 4 года назад

It's usually caused when the hole is connected to ground. The ground plane on the board is usually a large flat piece of copper on one of the layers and it dissipates the heat from the iron. In these circumstances I usually grab a larger soldering iron tip so that I can get more heat to the area, add a bit more fresh leaded solder and voila.

@eden12340 4 года назад

I'd recommend to anyone that needs to do this kind of pad rebuild the jumper coil strategy. It scales from the smallest pads up to very large pads and with the correct gauge wire the component will sit flush. Assuming you use the correct overcoat color the repair can in some cases be practically invisible.

@uptwisting 3 года назад

Find a problem with a board, go to youtube to find a solution, go through a lot of information light videos, end up finding a Branchus Creations which tells me most of what I need to know and answers some questions I have too. Standard.

@pauloutten3628 5 месяцев назад

Hi I really enjoyed watching your video. Just wondering what type of flux you are using to dispense it so easily. I've tried the liquid flux with the little brush, which was rubbish stuff, the solid flux in a tin, which is hard to work with.

@DanG-ug1ed 4 года назад

For those of you who are new to soldering. There is a cetification program called IPC. I worked as IPC certified for several years. Being polite: this stuf is not IPC certifiable.

@BranchusCreations 4 года назад

As I've always said in my videos, my way isn't the right way, just the way that works for me. I'm not actually certified at... anything. I just fix stuff.

@Synth2000 3 года назад

So how is the IPC way to fix lifted pads, if any?

@thebeerinnandrewmckenna2655 Год назад

Can you do a through hole pad repair please, because the cheap single sided boards, the pads where the conponenents go through, they burn off

@prashanthb6521 3 года назад

Meticulous work sir, thumbs up !

@kjamison5951 3 года назад

I can confirm that I use a Swann-Morton scalpel when I am removing the mask from vias to get a good surface for solder. You mention pads and we also call them lands. Anyone know the difference?

@ovalwingnut 4 года назад

Enjoyable video. Thanks for inviting us over.

@MikeysLab 4 года назад

Awesome video, thank you, I have used similar techniques in the past, but never thought of using thicker wire, usually just use wire wrap wire and hot glue the hell out of it, I like your idea better :)

@joeelias2515 4 года назад

Very excellent tutorial I must say,plus I really admire the quality of your scope, clear and crispy imaging and I can only wonder what it's make and specs are,very impressive!

@BranchusCreations 4 года назад

Thank you! Details for almost all the equipment I use are in the video description. If there's anything you can't find there, please let me know.

@Handle_number_7 4 года назад

"We won't worry about that pad, because it doesn't go anywhere" So essentially, on that board it doesn't require that leg of the IC chip? Fascinating. I may be dealing with a similar situation. 2 out of 8 pads came off, but may only have to repair one.

@hunterday2573 4 года назад

Kevin Ketelson just be careful that it’s not a multilayer board. At work we use 7 different layers of traces. It may be an internal trace.

@Handle_number_7 4 года назад

Thankfully, those legs of the IC chip were redundant on this board, so it didn't need them. SWEET! They were literally just anchor points.

@johncoops6897 4 года назад

@@hunterday2573 - an "internal trace" still has to connect to the other layer. So there will always be a via (hole) to get it there.

@natedawww 5 лет назад

That was fabulous. Thank you!

@Creamen 2 года назад

Thanks a lot, unsure I did it well but I have been able to fix some tracks damaged by cap's leaking on a PC Engine GT . I hope it will do the trick else shoganai as people say in Japan :)

@deven6518 3 года назад

i have used this method often but i wonder, will copper tape cut to the size of the pad and some e-7000 conductive glue work? Edit: I ask because some boards are all SMT and the traces may not have anything in sight to anchor to.

@t1d100 4 года назад

I understand that the UV mask is doing duel duty... Mechanical security and insulation. But, I think I would add mechanical security to the component body. Some type of adhesive that can be removed, if need be. Maybe the white adhesive used on big caps. I like Shoe Goo; no kidding. It's great stuff. Hot glue is not appropriate, IMO. I might also flatten the wire that goes under the IC and coat it with mask, before seating the IC, to prevent gaps between the pad and pins.

@theoryismypraxis3538 3 года назад

what is preventign us from jsut putting the old pad where it was with some glue. pr ppssobly wth the same glue by heating it up? and then .,, if needed, we could scrape away some of the insulation on the trave a connect the pad with the trace by solder?

@FrightBites 2 года назад

were you using the 28 gauge wire for this?

@SeanCMonahan Год назад

Oof. I ripped a bunch of pads off using desoldering braid that I accidentally let cool too much before pulling away from the board. Let's see if it's recoverable. One of the pads was a through-hole whose pad was also the bridge between two parts of the ground plane, and on one side of that pad I destroyed, there is only a bank of the teensy SMD capacitors. Literally the only SMT components on the entire board are these capacitors whose ground connection I've just severed...

@Normanb15 3 года назад

I wonder if you can help me... I dropped an older Sony dream machine and it hit the kitchen lino very hard and now it shows no sign of life. I checked the circuit board and don't see and broken pieces. No broken plastic. I checked the electrical cord for continuity to its soldered connections and it doesn't appear to be broken...there was continuity to the thick pad of solder for each one. Any advice on what to look for next?

@revengenerd1 3 года назад

I was a bit stupid and misunderstood "scrape a bit of the via to expose the solder" and removed the entire solder on it so now cant solder to it, I tried tricks like trying to put a thin bit of tinned wire in but no luck as it just blobs up, someone suggested conductive paint but im not sure if that will work.

@TheElectronicDilettante Год назад

Thanks for the informative video. You demonstrated how easily a pad is removed at beginning of video. Is it possible to remove a pad in the you used , from a donor board, then use the removed pad to replace a damaged one?? Hospital smell from wire enamel = iodine in the enamel? Thanks for your time -Jason Burchell

@pr0xZen 4 года назад

UV solder mask is also good for securing jumper leads to the board if you have to jumper a component from quite far away, and to keep non-enameled leads from moving about, shorting on other stuff. The great thing about UV solder mask vs superglue, rapid cure epoxy etc - is that you can work with it in your own pace and clean it off fairly easily - it doesn't cure until you UV expose it. Just note; many UV solder masks will go opaque on the surface when curing. So don't put on (a single layer) thicker than neccessary. If the surface cures firmly before the rest underneath can cure, the rest undeneath will stay liquid indefinitely.

@BranchusCreations 4 года назад

UV mask has a thousand and one uses when it comes to board repair, I use it every day. I shot this video a while ago, but these days I use a UV laser to cure the mask, as it does it in just a matter of seconds, and they are very cheap to purchase.

@arnolduk123 4 года назад

@@BranchusCreations Do you know what that red glue is called, sometimes used to hold components in place on the board ? It looks like melted hot glue but it has a deep red color.

@BranchusCreations 4 года назад

@@arnolduk123 Hi Ace. It's actually just called surface mount adhesive. I buy mine from RS Components here in Australia. I'm sure it's available from other places too. au.rs-online.com/web/p/epoxy-resins-epoxy-adhesives/0567581/

@stuartbarnes9930 3 года назад

Hi there great video. I have a question? I have a PS4 bored with the the power supply connector ripped off. The connector sits on 4 pads, 1 of the pads has come off and is hanging on only by the green coating. This pad doesn’t seem to have another connection to anything else. So am thinking correctly that it mite be a earth?? Could I simply solder the old pad back on? Or do I need to make a fresh/new pad from scratch? Any feedback would be grateful. Cheers Stu.

@herrlip72 4 года назад

BOB ROSS! Love it

@tweakerman 5 месяцев назад

What happens if the pad has been removed from too much heat, but the trace is under the surface & you can't see it (a multi layered circuit board) how do you repair that?

@user-fl6ui1pr9l Месяц назад

hi, nice video out there! what temperature do you use to melt the soldering wire at this video??

@keithking1985 Год назад

Brilliant thanks Bruce just what I need to fix my Bluetooth speaker.. 👍🇮🇪💚🙏🏼 P S. Can you replace a pad on a board? Do you have any videos showing how to do that?? Thanks P.P.S. THIS VIDEO IS SHOWING WHAT I NEED. I AM JUST AWAKE SO EXCUSE MY STUPID QUESTION. 🤣 NEED TO WAKE UP MORE. IL SAVE THIS VIDEO. AND I HAVE SUBSCRIBED TO YOU.

@thhomasmarks 2 года назад

I'm having some serious problems, my thumb drive stopped connecting it was a solder connection on the number 3 pin the USB plug I ended up removing it and wiring directly to the board out to a USB socket that I just plug it in, however it is not working it is heating up I have the wires in the correct configuration however I may have scratched the motherboard so it maybe it's shorting out, can you advise?

@etiennebonanno 8 месяцев назад

Circa the 18:05 mark you say something that sounds like "oooh ehyyah"...this to me sounds like a common expression showing mild frustration in Maltese, my mother language. Is that right, or am I just imagining things?