No video :(

Replace your coolant || Mazda CX 5 CX 3 Mazda 3 6 Biante Skyactiv

Подписаться 13 тыс.

Просмотров 162 тыс.

50% 1

Hello fellow viewers . Welcome back again to this channel. I hope you all are in a good health and well being. I really apologize I haven’t been uploading any youtube content for the past months. But that said I haven’t forget about my youtube world which means a lot to me and without your supports my beloved subscriber and support from my family & friends I would not be here where I am .
This video will cover step by step how to replace the radiator coolant on this Mazda CX 5. This will applies to all Skyactiv engines 2.0 & 2.5 Mazda Skyactiv. This specific vehicle requires approximately 4.7L of replacement coolant & special coolant from Mazda FL22.
This is not a full coolant flushing service
If you live outside Asia and can source FL22 at your dealer please do buy it, in my case and for Asia (Indonesia) region the dealer do not get FL22 coolant from Japan anymore and I had consult with my local dealer which recommended replacement coolant that are equivalent to FL22 Replacement Coolant.
Mazda recommend to replace coolant every 5 years / 100.000kms.
Please do this at your own risk I will not held any responsibilities of any damage that can occurs whilst doing the service , Always be careful when working underneath the vehicle.
To bleed the air out of the radiator / cooling system please follow this direction (Radiator cap removed).
1. Once everything topped up, turn on the car and let it idle normally.
2. Run the engine at 2.500rpm for 5 mins until both radiator fans kicks in.
3. Let it idle for 5 second & recheck the coolant reservoir (top up as necessary)
4. Run the engine at 3.000rpm for 5 to 10 sec.
5. Let it idle normally then recheck the coolant reservoir.
6. Inspect any leaks & reinstall service hole cover.
7. Done .
INDONESIA ONLY: PLEASE VISIT MY ONLINE STORE FOR PERFORMANCE PARTS
www.tokopedia....
Stay Connected : Instagram @ felixdan_
Music credits to :
Song: XIBE - We All Together (Vlog No Copyright Music)
Music provided by Vlog No Copyright Music.
Video Link: • XIBE - We All Together...
Song: Ikson - Heaven
Music promoted by Vlog No Copyright Music.
Video Link: • Ikson - Heaven

Опубликовано:

14 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 261

@charlesbartholomew2910 3 года назад

Thank you for sharing the step by step. Now I'll be ready to do mine when it's needed. I like how you clean all of the parts that you disassembled to complete this task. It shows a person that pays attention to the details and takes pride in caring for his cars. Keep up the good work! I look forward to seeing more.

@FelixDanGarasiAuto 3 года назад

Thank you sir

@davidpancerz5820 5 лет назад

Hey FD, great to see a new video of yours featuring the Mazda. I'm your subscriber in Texas who owns two CX-5s, a 2014 model and the other a 2015. Since you hadn't done this service yet, I did a complete coolant flush to my 2014 car last summer. At 50,000 miles (not kilometers) I found this really wasn't necessary as the coolant that came out was as green and sweet smelling as the new FL22 that I put back in. Compare that to the transmission service I did where the fluid was brown and nasty. I took about a week to perform my coolant service as I used a radiator flush chemical that again wasn't needed at 50,000 miles. Once I drained the radiator as you show, I used compressed air to remove as much fluid from the system as possible. Then I added the radiator flush chemical and many gallons of distilled water. All during the week I'd drain the radiator and add more distilled water in order to get out all the antifreeze that was circulating in the engine and heater core. Once I was satisfied that all the old fluid was out I used a cool bit of kit that I had bought to service the radiators on my BMW motorcycles that don't care for ANY air in the system. Google UView Airlift Coolant Refill Tool. I used this tool and one of my large air compressors to literally suck in the new FL22 without introducing any air bubbles. Also cleaned my overflow reservoir just as you but my tank has two lines - one for Cold and the other for Hot. Another super video Felix! Looking for you to change out the water pump belt next (not the easier serpentine belt). Take care!

@jonathandodd6712 5 лет назад

David Pancerz I too am FD's Texas Mazda guy! 2013 CX-5 in Grand Prairie!

@FelixDanGarasiAuto 5 лет назад

Thank you so much guys . I definitely will share more videos for us all. Appreciate your support and info tips.

@renenowicki 2 года назад

Got to get that water pump belt on the crank pulley and push/pull onto the smooth part of the water pump pulley. It will stay put once on there. Then turn the crank while pushing it over. Wear gloves and watch you don’t catch your fingers. Keep cranking. It will catch.

@davidpancerz5820 2 года назад

Yep, replacing that belt wasn't hard at all. It's mainly a space issue if you have large hands. And since I changed the spark plugs at the same time, the engine was much easier to crank over. Definitely helped getting that water pump belt on.

@renenowicki 2 года назад

David Pancerz i did plugs too. Didn’t occur to me to leave them out. Brilliant!

@GOVAUS1 5 лет назад

Thumbs up for the cleanest engine bay I've seen. Good for you. Nice video.

@FelixDanGarasiAuto 5 лет назад

Thank you sir. :)

@billyshears2286 2 года назад

A great video Dan. Very helpful thankyou ..... A tip = to drain the reservoir, if you leave the radiator cap on when you remove the cockstop, the system will suck out the fluid in the reservoir while draining. You might need to squeeze the top radiator hose to help the fluid flow.

@FelixDanGarasiAuto 2 года назад

thank you Sir. Noted.

@lovemedia3226 2 года назад

hey what's the lockstep?

@mz6187 4 года назад

Awesome videos, my 2014 Mazda 6 still strong at 129,000 miles

@FelixDanGarasiAuto 4 года назад

Its a very good car :) just have to maintain it right.

@mohdsyufian3952 4 года назад

Hi , nice works .. but actually what happens at the SC is we did replace the coolant inside the engine so total amount coolant needed to be replace is almost 8 litres... this comment is regarding to all my recently customers showing this video and asking why it should be 8L i hope all of your viewers understand or you can make another content about it ... 👍 keep up your good work ...

@FelixDanGarasiAuto 4 года назад

Ya i think i have note down in the description as this method is only for basic drain and fill the radiator system and not full flushing whole fluid inside the engine.

@Warmsunset26 Год назад

Thank you. You did confirm my research - on the FL22. Here in the UK, that is what they are referring to. Nice one.

@FelixDanGarasiAuto Год назад

no problems sir. glad it helps.

@EricPark971 2 года назад

Fantastic videos, Felix. Why do you do this on a shiny new car with 33,000 km is a mystery... Much appreciated👍👍

@FelixDanGarasiAuto 2 года назад

it has been collecting dust since 2013 as i drove my other car for the daily , I have not driven it much and yet enjoy this cx 5 . So i though why not do a coolant / radiator maintenance just incase the old one fail and freezed up. But yeah now the car is 10 years and been enjoying it and driving it as my daily car.

@queensapphire7717 Год назад

Yeah, I did a drain and fill of my transmission at 30K miles for the “Lifetime” (not) trans fluid. New Mazda FZ fluid is sky blue in color, what came out was filthy, brownish stuff, at 30k miles !!! Do not fall for this “Lifetime” or “Sealed” nonsense regarding fluids / lubricants. Changing is simple, and just replace the same amount you take out, plus 2-3 ounces for “stick around” amount on the sides of the catch basin, after measuring. Lifetime means life time of the warranty, for which after they can charge you $6000 for a remanufactured transmission.

@tiffanyabigail9103 5 лет назад

Whoah what a helpful video. Thankyou so much. Please making more tutorial video like this. From today i am officially your subscriber 👍🏻 although my car isn’t cx 5, mine is mazda 2 skyactiv 😁

@FelixDanGarasiAuto 5 лет назад

Welcome. :)

@agusdjauhar9376 3 года назад

Hi Felix, terimakasih. Your video will be my guidance to replace of my CX 5 water cooolant. It is very detail and easy to follow.

@FelixDanGarasiAuto 3 года назад

Welcome Sir 😎✌️

@Tempdownloads1 3 года назад

Can you post a video of replacing the thermostat on your Skyactiv engine please?

@moileung 4 года назад

The official FL22 coolant (4liter) I bought at a Mazda dealer here in Canada is $25.**+ Tax so about $28.xx Canadian.

@pete5534 3 года назад

Good for you! The FL-22 stuff isn't 'cheap,' but using the proper coolant feels good. I often purchase products from my local dealerships, and save one time, have always had a good experience.

@JY-tq4ir 2 года назад

great, same design as Mazda3 2017, i can clearly see structure of coolant, using this

@FelixDanGarasiAuto 2 года назад

Yea they are similar and you can follow these simple steps to get the service done your self at home. 😁

@cruxfitvancouver 5 лет назад

Watching the old coolant draining out is oddly satisfying...

@FelixDanGarasiAuto 5 лет назад

Thanks man . Dont forget to subscribe & like this video to give your full support. Thank you again for tunin in.

@warfarewar8206 5 лет назад

fantastic video really like the way you explain and show how its done!

@FelixDanGarasiAuto 3 года назад

Thanks Man :)

@cafemolido5459 28 дней назад

Great job

@FelixDanGarasiAuto 28 дней назад

@@cafemolido5459 Cheers my friend .

@unclebean8367 2 года назад

For indonesia, you can also use Shell Coolant Longlife Plus 30/70, which comply to JIS K 2234 as genuine mazda coolant (non silicate, non borates, non nitrite, non amines).

@FelixDanGarasiAuto 2 года назад

Noted will give it a try :)

@pipediaz6631 4 года назад

Amigos podrías decirme dónde se encuentra el sensor de temperatura del refrigerante en Mazda cx 3?

@NBnKB2525 5 лет назад

Thanks for all the great content!

@FelixDanGarasiAuto 4 года назад

no probs

@AlienwareAlienware136 Год назад

Nice video. Sincerely appreciated!

@FelixDanGarasiAuto Год назад

🙏🏼🙏🏼🙏🏼👍🏼👍🏼👍🏼

@dogukanertan4707 Месяц назад

We're going to run it with the radiator cap open, isn't it right? So when do we turn it off? After the engine fan comes on? Can you help?

@FelixDanGarasiAuto Месяц назад

yes that is correct , run until the fan kicks in and you can turn off the car and top up the coolant fluid.

@pipediaz6631 4 года назад

muchas gracias .esperando mas videos de mantenciones mecanicas de mazda cx3

@FelixDanGarasiAuto 4 года назад

Thanks sir. Stay tune for more cool videos.

@samueljang8133 Год назад

Thank you for the excellent content. Too easy with your complete instructions. Appreciate it. You have noted that this is not a complete coolant flush. What is complete coolant flush??

@FelixDanGarasiAuto Год назад

Thank you again for the support. full coolant flush you have to drain all coolant from the engine block and to do that you have to uninstall the bottom part of the radiator hose .

@ericj6559 Год назад

Sometimes the capacities are a bit confusing. Just make sure to check the owners manual as mine states there are slightly different capacities depending on the VIN. Japan or Mexican built makes a difference.

@FelixDanGarasiAuto Год назад

Right i would stock about 7litres of coolant. Some cars uses only 6litres and other may use about 7litres. As you dont want to be short on coolant if you are doing the service at home.

@taichihead42 27 дней назад

Hi Felix Dan, in regards to the bleeding procedure on your Mazda and all Mazda's you state that owners should remove the radiator cap while bleeding the system. But won't coolant splash everywhere and make a mess out of my engine. As well as that, coolant get"s really hot very quickly and running the car for 5 minutes at 2,500 rpm would definitely have it boiling, especially if the fans kick in. I didn't see you doing this in the video.

@FelixDanGarasiAuto 27 дней назад

@@taichihead42 its normal to have some mess spillage while bleeding without the special Tool Spill free radiator filler cup / bucket. Just rinse it off with some water you all good to go. Unless you have the radiator spill free filler tool / bucket then you r save from the spillage mess. 👍🏼

@taichihead42 26 дней назад

@@FelixDanGarasiAutoIn the past Felix i have changed coolant on other cars and i never left the radiator cap off. It seems like a really dangerous thing to do and once that coolant gets hot it will shoot up out of the radiator and the spray will go every where. Running the engine checking for leaks and topping up the radiator when cold is far more sensible. Who came up with this idea to leave a radiator cap off a hot radiator also that funnel tool seems unnecessary as well. Unless radiators have changed since the 1980's.

@wph0927 5 лет назад

How many km before you chnge the fluid. Mazda said long life coolant can last 100tkm. And do you need to use radiator flush

@FelixDanGarasiAuto 5 лет назад

Hi Wilson . This car is 5 years now , so thats why i am replacing the coolant. Radiator flush isn't always necessary unless the coolant are very very dirty and the car is very old .

@zsoltie95 3 года назад

My mazda book: 10 years or 200.000 km.

@robertflink8017 7 месяцев назад

Great now I will do mine thanks

@FelixDanGarasiAuto 7 месяцев назад

no worries let us know how you go.

@abujudyalzahrani8535 4 года назад

Thank you from KSA

@FelixDanGarasiAuto 4 года назад

no probs

@aldenleonardo 3 года назад

Great vid! Thanks for sharing!

@FelixDanGarasiAuto 3 года назад

no worries 😉

@DIY-Unboxing 11 месяцев назад

How did u remove pins from the pipe at coolant reservoir? U showed how to clip back on after cleaning it but did now show how to unpin the clip to take out the coolant reservoir

@FelixDanGarasiAuto 11 месяцев назад

its just snaps back in n out. Use gentle force. Cheers

@sebbbou5455 5 месяцев назад

Very nice video! For the bleeding part, When you start the car at the end and let it idle... when you turn off the car again, do you re open the radiator cap to let go air bubbles?

@FelixDanGarasiAuto 5 месяцев назад

it dont matter. u can turn off and open the radiator cap to check or you can leave it close.

@sebbbou5455 5 месяцев назад

Thanks!

@dreiandy3775 3 года назад

i have a question, when is the right time to change a coolant? been using my mazda CX-5 2015 for 3 years now. tnx

@FelixDanGarasiAuto 3 года назад

100k kms or every 5 years

@dreiandy3775 3 года назад

thank you for the quick response FD. i already subscribed your YTchannel. have a nice day ahead.

@FelixDanGarasiAuto 3 года назад

@@dreiandy3775 You r welcome :)

@EVREY767 2 года назад

You are just a neat and pedant) Thanks for the video, from Russia!

@FelixDanGarasiAuto 2 года назад

thank you I appreciate that :)

@jptuaz1992 3 года назад

what is the interval on coolant change? my mazda 3 2015 coolant is still green but near the low level on the expansion tank. not sure if it was changed before as i got the car used.

@FelixDanGarasiAuto 3 года назад

change the coolant every 4 years or 80k kms

@ton6924 4 года назад

Thank you so much for this video.

@FelixDanGarasiAuto 4 года назад

you r welcome Anusorn

@gordonmclatchie3339 3 года назад

Have you replace the rear diff bush, looks fairly easy to do but would like to watch you do it in a video .

@FelixDanGarasiAuto 3 года назад

unfortunately we dont get 4wd cx 5 :(

@alghamdi9999 2 года назад

Thank u my dear , no need to vented the sys for any air inside the loope ?

@FelixDanGarasiAuto 2 года назад

No need

@aytacdede81 4 года назад

good video you left reserve bottle empty ? each how many km must replace coolent liquid ? how about red coolent liquid thanks

@FelixDanGarasiAuto 4 года назад

I refilled it to max level prior starting the vehicle. I used the oem coolant from my local mazda dealer. The colour is green for our cars. I am not sure about red. Please check with your local mazda dealer to confirm.

@timgifford4637 3 года назад

Thanks for another excellent video. I would recommend draining the fluid from the lower radiator hose rather than the petcock, which, with age and heat can become brittle and break, which would not be good. Thanks again.

@FelixDanGarasiAuto 3 года назад

👍 noted :)

@SuperDancingdonkey 3 года назад

What a great video!

@FelixDanGarasiAuto 3 года назад

very much appreciated 🙏🏼

@SlavaKolesnikov 4 года назад

so low milage and u have already changed it? Due to workshop manual it is changed after 120 000 km or 10 years

@FelixDanGarasiAuto 4 года назад

Just want to demonstrate how to for us all.

@TheSchmed 3 года назад

I do at the 1/2 way point what manufacturer states. They said trans fluid at 120K miles, I do at 60k miles, oil change every 10k, I do every 5 k.

@StellasEgyptologyFacts 10 месяцев назад

Vibing to the song hard 😂

@FelixDanGarasiAuto 10 месяцев назад

🤣😂

@tomwu4211 5 лет назад

Very nice video you have there and thank you so much for making a video. :) This will be use on my Mazda CX-5. But I have a question from you. Once everything is all topped up and it’s time to bleed air out from the radiator Cap. Do I have to keep the cap open to let the air bubbles out while I run the engine RPM?

@FelixDanGarasiAuto 5 лет назад

Yes please follow the bleeding procedures. As mentioned on the description below with radiator cap removed. Once it burps completely. You are done :) pls dont forget to subscribe and hit that notif bells for us so you wont miss a latest videos. :) thank you again really appreciated your time tuning in Mr Luigi.

@tomwu4211 5 лет назад

So, after I run the engine’s RPM and there still have bubbles coming out, I just leave the engine run normally until it stops burping?

@FelixDanGarasiAuto 5 лет назад

@@tomwu4211 correct sir. Just until theres no more burping.

@tomwu4211 5 лет назад

Felix Dan Thank you very much. :)

@FelixDanGarasiAuto 5 лет назад

@@tomwu4211 dont forget to wash off the spillage sir. :).

@zen4517 Год назад

Hi Felix, want to ask you that is it ok to use other brand of common coolant (APM brand coolant) for Mazda car? as the shop owner use this instead of Mazda FL22 coolant..

@FelixDanGarasiAuto Год назад

if it does have similar spec yes definately can use. Personally i have not tried other brand coolant for the CX5.

@zen4517 Год назад

@FelixDanGarasiAuto thanks for your reply.. as this is the shop owner (specializing in Radiator repair and service) recommend, so I just go with this..

@juanr3716 5 лет назад

Hi Felix, greeting from the US my friend - thank you very much for your videos - they have been a great help. This will be my next service to do on the cx-5. I have 75,000 miles (120k km?) and I am not sure if I should do the flush or just the coolant replace like you do. Can you comment? If you think it will be worth doing a flush - can you tell me the extra steps to take? Also if I do a flush will I still need 5L or it will be more?

@FelixDanGarasiAuto 5 лет назад

To fully flush the cooling system , you will need to drain the coolant from the radiator and add flushing chemical diluted with distilled water and keep repeating (draining) until there are no more excess old coolant. Yes you will need more than 5 L of coolant to refill the system.

@MandeepSingh-fw9vd 3 года назад

Hi ! I have green colour coolant in Mazda . Now I purchased coolant recommended by Mazda but it’s blue colour. Should I empty green one before putting new blue one , or it’s fine if I left green inside and put blue one on top ? Thank you !

@FelixDanGarasiAuto 3 года назад

I would empty it first.

@evansjamal6554 18 дней назад

Thank you very much, your video was helpful🙏

@FelixDanGarasiAuto 18 дней назад

@@evansjamal6554 you’re welcome 😁🙏🏼

@geoffj83 9 месяцев назад

I bled the cooling system with the radiator cap on instead. I realized this mistake a couple days after and then did it again with the cap off. Is it possible that there's air in my system from bleeding it improperly the first time?

@FelixDanGarasiAuto 9 месяцев назад

yeap definately can re do the service just let the car idle and uncap the cap fill the rad till full and let the car bleed it self until the 2nd fan kicks in then you r done 👍🏼

@pabloe1802 5 лет назад

I used a large small funnel to avoid the mess

@thisisudax 2 года назад

great video thank you!!

@FelixDanGarasiAuto 2 года назад

No worries :)

@hmn4124 4 года назад

what about the coolant still left inside the engine?

@FelixDanGarasiAuto 4 года назад

It will b left inside the engine. Reminder that this method is not a full flush method.

@TheSchmed 3 года назад

Do it again after driving 20-30 miles, a bit of a waste, but will pretty much get all old coolant out.

@aurelianpetrescu9151 20 дней назад

Congrats👍🏻.. How much coolant did you use exactly?

@FelixDanGarasiAuto 20 дней назад

If you r only drain n fill , Get yourself 5 ltrs should be plenty.

@aurelianpetrescu9151 20 дней назад

@@FelixDanGarasiAutothank you

@dylanmurphy744 2 года назад

I noticed you didn't burp your radiator, you put the cap on when starting your engine, if you leave it off it releases the air in the system, which in turn will not let the coolant get to critical parts of your system easily, and may result in the ac not blowing the correct temperature. I could be wrong and maybe you did burp the radiator and just didn't record it

@FelixDanGarasiAuto 2 года назад

dont worry i did just i didnt show the method fully here. My cx 5 is fine ever since done this service 👍🏻

@dmc_77 2 года назад

hi what do you need to do to burp the radiator?

@FelixDanGarasiAuto 2 года назад

@@dmc_77 remove the radiator cap and let it idle for 15 to 20 mins and let it overflow until it stop.

@pipediaz6631 3 года назад

Amigo podrías decirme porfavor donde se encuentra el sensor de temperatura del Mazda cx-3?

@mellymcd3535 4 года назад

great informtaion. could you do more explaining with spoken words for the steps? Looks like the car has to be jacked up to drain old coolant. You made it look so simple! My engine is idling very rough and I don't know what is wrong with it. I have only had it for 6 months and think I way overpaid for it.

@FelixDanGarasiAuto 4 года назад

Maybe theres a leak within your intake. Please check. Defect Throttle body gasket / intake manifold / vacuum hoses. Please check them first.

@mova_2020 3 года назад

So you pour the same thing in both coolant reservoir and radiator? I thought it should be a specific mix of water/coolant in the radiator and a full coolant in the reservoir? Am I wrong?

@FelixDanGarasiAuto 3 года назад

This coolant is premixed just have to fill it without adding water. Unless you have the other coolant that needs to be mixed with water please mix it with correct amount level of water.

@warfarewar8206 Год назад

why didn't you replace the thermostat? is it not called for?

@FelixDanGarasiAuto Год назад

nope mine is totally fine.

@DemonHunter0069 Год назад

Good vid

@FelixDanGarasiAuto Год назад

cheers 🙏🏼🫰🏼

@tuslin Год назад

Hi, why cars in your video without license plates?

@FelixDanGarasiAuto Год назад

we do have license plate.

@eoved1 4 года назад

Very nice

@FelixDanGarasiAuto 4 года назад

Thanks

@zaldycustodio4635 5 лет назад

Very helpful

@FelixDanGarasiAuto 5 лет назад

cheers.

@kestertheidk-707 4 года назад

Hi am from Thailand.😄

@mindu9766 3 года назад

1:19 start (for my own reference)

@grandprixuse 5 лет назад

Thanks for the vid! I had been waiting for this, I've had the coolant for 4 months stored away lol, but hey, where is the thermostat, I wanna take a look at it just for safety

@FelixDanGarasiAuto 5 лет назад

You are welcome Juan. Thermostate hidden somewhere in the engine bay . If you follow route of the top part of radiator hose and follow to the engine thats where it sits. If you dont mind dont forget to subscribe ,like and share this channel to your friends it is very much appreciated.

@blackriderph4340 8 месяцев назад

Hi Felix! I did the same procedure and i only used less than 4ltrs of fl22 coolant. Mazda 3 2.0 skyactiv.

@FelixDanGarasiAuto 8 месяцев назад

did you already bleed it? and top up the coolant reservoir. It should be about 5 litres or so.

@blackriderph4340 8 месяцев назад

@@FelixDanGarasiAuto yes i followed everything. I even checked the service manual too.

@FelixDanGarasiAuto 8 месяцев назад

@@blackriderph4340 ok thats no biggie as long as the cooling system are bleed properly and fluids topped up your car should be all good to go.

@blackriderph4340 8 месяцев назад

@@FelixDanGarasiAuto yes thats what I figured. Im having no issues so far after a long drive.

@harminparra7678 3 года назад

Question: Is it necessary to remove the reservoir in order to change the coolant? Thanks

@FelixDanGarasiAuto 3 года назад

Yes better to remove the oil coolant from the reservoir. :)

@godwinsantiago8570 3 года назад

Do you have to fill up the coolant if you have a blue indicator warning? I have a mazda cx3, the coolant level is one inch below to the full level

@FelixDanGarasiAuto 3 года назад

Top it up.

@Mandozts 2 года назад

Blue indicator means engine is cold so dont drive agressive for couple a minutes

@dminyoutube7832 4 года назад

Is there any need to use special equipment to replace the coolant ?

@FelixDanGarasiAuto 4 года назад

Nope. Just standard hand tools. If you have anti spill funnel its even better.

@charlesnorton2441 4 года назад

Always wear gloves and eye protection with coolant, it is toxic

@GD-sq2vj 3 года назад

Hi, I have a question .I own a Mazda 3 2014. I followed all your instructions but only 3 liters drain out. Can you tell me why and give me any advice?

@FelixDanGarasiAuto 3 года назад

it should be more than 3 ltrs… i think before hand you did not top up the radiator coolant to max line everytime it needs topped up. ??

@GD-sq2vj 3 года назад

@@FelixDanGarasiAutoThanks for your quick reaction. this was the first time I tried to change the coolant. It was topped up,no leaking, no problems. As I said, I did exactly what you did and only 3 liters drained out. I even repeated everything twice.with the same result.

@ivanfernandez1858 Год назад

Hi nice video. Will the reservoir drain too if left attached? Thanks.

@FelixDanGarasiAuto Год назад

you have to take it out and drain it .

@netzamorales583 4 года назад

Can you back flush a heater core on a 2014 Mazda CX 5?

@FelixDanGarasiAuto 4 года назад

I'll see what i can do for that.

@queensapphire7717 Год назад

No need for one of those “Burp” Funnels and let run for 20-30 mins to make sure all air is out of the system ?

@FelixDanGarasiAuto Год назад

If you have the burp funnel would be much better so no spillage whatsoever. But if you dont have would be oke just to let the car runs until it burps for 15 mins or so and just top up the coolant once done.

@phils.3178 Год назад

Can I use Prestone?

@FelixDanGarasiAuto Год назад

check their website to confirm. im sure they have something for mazda

@RSi-tf3jx 3 года назад

I would also recommend to drain the engine block after you drain the radiator.

@ZhuSeth 3 года назад

I wouldn't say so, in these newer cars it's not necessary to fully drain and in fact can hurt the seals.

@RSi-tf3jx 3 года назад

@@ZhuSeth what seals

@diyersamateur5486 3 года назад

Malam pak felix, mhn maaf sblm nya kalau mengganggu. Mau tanya lagi pak, apakah mazda skyactiv compatible pakai coolant yg ada di tutorial? Kalau sy cek buku sih minta nya FL22 yg kata ny sih 55% ethylene glycol. Mhn penjelasan dan konsekuensi nya dengan penggunaan selain coolant FL22. Terimakasih

@FelixDanGarasiAuto 3 года назад

Untuk di video ini sy beli di dealer mazda langsung dan direkomendasi pakai mazda coolant yg ini kata dealer mazda komposisi formulanya hampir sama dengan fl22. Tapi yg sy baca baca dr forum luar spec coolant Fl22 formulanya anti freezenya tahan lebih lama sampai dengan 10 tahun dimana coolant dengan formula biasa hanya tahan sampai 5 tahun. Dan kalau tidak memakai fl22 mungkin hanya harus menggantikan coolantnya lebih awal saja periodenya supaya tidak terjadi penyumbatan / karat pada komponen mesin water pump dan radiator. Tapi untuk mesin skyactiv sangat direkomen untuk menggunakan fl22 dan kalau bisa dapat fl22 di mazda dealer beli aj fl22 ya.

@shahmirulhizam3366 3 года назад

Hi, how remove clips wire harness on minute 9:20? I scare if pull it hard, it will broken

@FelixDanGarasiAuto 3 года назад

have to use skinny pliers for that one.

@shhhdontshout 4 года назад

Hi dan, i got an oil spot on top of my alternator, i saw its coming from the oil pressure sensor(i think) that sits on top of it. Is it just a simple repair(change of o ring) ? Oh,its a m2 skyactiv.

@FelixDanGarasiAuto 4 года назад

Check if the o ring washer needs replacing. Or even the oil pressure unit.

@comando293 4 года назад

Look at the part called the oil control valve. It has a seal which is prone to leaking, and the valve itself can leak.

@gibsonindistress418 5 лет назад

My coolant is really low. Can i top it off or do i need to flush and put new fluid in? Also I have no idea what brand of coolant is currently in my car, do I have to use the same brand to top if off? Or can i mix brands if it's the same color, i,e green coolant fluid

@FelixDanGarasiAuto 5 лет назад

Get the same brand coolant.

@gibsonindistress418 5 лет назад

@@FelixDanGarasiAuto Will do. Thank you. Also, on your throttle body cleaning video, you said torque it back on with 8mm of torque. What would that be in foot to pounds? I've been trying to find the specs, but I can't find it.

@FelixDanGarasiAuto 5 лет назад

@@gibsonindistress418 about 6ft pounds. Just about snug.

@gibsonindistress418 5 лет назад

@@FelixDanGarasiAuto Thank you very much sir! Is there a website where I can find all the specs for bolts and what not for my Mazda 6? Again, thank you for taking the time to reply.

@zandrojayme1828 Год назад

Is your engine 2.5 liters?

@FelixDanGarasiAuto Год назад

mine is 2.0L

@moileung 4 года назад

Anyone on the comments can tell what year model is this cx5? (My cx5 is 2015 and it doesn't have this blue covering, just black)

@FelixDanGarasiAuto 4 года назад

Year 2012 - 2014 with 2.0ltr skyactiv has blue. Other than that with 2.5ltr skyactiv has black .

@thunderhype5972 5 лет назад

Hi bro, Is this consider a full flush or half flush? If i recall correctly, the engine is build with tunnels which allow the coolent to flow within to cool off the engine. Hence i saw how mechanic used to insert water pipe n flush out dirty coolent. When doing refill, they turn on the engine so as to see if the water pump has pumped all the water which will gone thru the whole engine appropriately then by refilling the reservoir if necessary.

@FelixDanGarasiAuto 5 лет назад

Hi George .This service was to replace the coolant only , not a full flush job as its not needed, the car is still 33000Ks on the clock, if you were to have older car with the coolant that hasn't been replace for its life then you will need to do the full flush job just like you mention above perhaps add a radiator flush chemical to help dissolve the gunk and dirt in the cooling system.

@heryoneheryone3664 4 года назад

Mas kalau pakai coolant anti frezee amsoil bisa cocok gak ya buat mesin Mazda 2 sky di Indonesia?

@FelixDanGarasiAuto 4 года назад

kalo speksifikasinya mirip sperti mazda punya seharusnya tidak ada masalah.

@yegago 2 года назад

Hi why do u use only 5 litres if my cx5 manual says the capacity are 9 litres aprox???

@FelixDanGarasiAuto 2 года назад

Yes correct this video just to show how to replace coolant from the radiator not full replacement including the left over from the engine block.

@yegago 2 года назад

@@FelixDanGarasiAuto my car year 2012 has 140k km, is not necessary to replace all the coolant? And is it ok if I put a coolant that is similar specs to the fl22 mazda, ? Thanks

@FelixDanGarasiAuto 2 года назад

@@yegago Yeah should be alright changing partial coolant is sufficient for daily car. Yes if can use similar spec to FL22 coolant.

@jremaine1 3 года назад

Wait did he spray the blue engine cover?

@FelixDanGarasiAuto 3 года назад

OEM sir

@betosanjaya4646 3 года назад

thanks

@FelixDanGarasiAuto 3 года назад

No problem

@ceezedgerman 3 года назад

When you drain the coolant via the petcock valve on the radiator does it drain all of the coolant or is there still some coolant left in the engine block? The Mazda service manual recommends flushing the cooling system once the coolant is drained, that's why I'm asking.

@FelixDanGarasiAuto 3 года назад

some of left over coolant will be in the engine block. you could flush it if you want :)

@ceezedgerman 3 года назад

@UCoJgjPIuMr0x0YR4yikLwvA Any idea how much coolant?

@FelixDanGarasiAuto 3 года назад

@@ceezedgerman should be 4 to 5 ltrs left.

@ceezedgerman 3 года назад

@@FelixDanGarasiAuto That seems like a lot, more than half the capacity. How do you get the rest of it out?

@FelixDanGarasiAuto 3 года назад

@@ceezedgerman to drain the whole coolant you have to disconnect upper hose thermostat and lower hose :)

@jimsinnovations2737 2 года назад

i need help fixing SBS brake thing and forward facing radar, any ideas

@FelixDanGarasiAuto 2 года назад

unfortunately you have to take it to Mazda Dealer for ABS problem.

@jimsinnovations2737 2 года назад

@@FelixDanGarasiAuto its not abs sorry its th e Epb for brake changes, anyway after brake change, it says it on my right screen, my left side where dummy lights come on, there is no lights on, just the 2nd screen on dash thanks man

@FelixDanGarasiAuto 2 года назад

@@jimsinnovations2737 maybe recheck the brake caliper, bolts and piston and do it all over again see if the light goes away.

@jimsinnovations2737 2 года назад

@@FelixDanGarasiAuto ty man will try that

@zainiaris 4 года назад

How many litres of coolant required?. 7L?

@FelixDanGarasiAuto 4 года назад

I have used approximately 4.7 litres in this video. As it is not a full flush service.

@mtay65 3 года назад

Should flush with distilled water at least 2 rounds with engine running for 3-5 mins before pouring in new coolant.

@FelixDanGarasiAuto 3 года назад

Definately can do that for the next service.

@oreeenoreeen7226 5 лет назад

What about bleeding no need?

@FelixDanGarasiAuto 5 лет назад

Bleeding procedure is neccessary. Please follow the direction in the description box. Thank you

@zamok1965 2 года назад

@FelixDanGarasiAuto Год назад

yes thank you

@victorcasillas6708 2 года назад

no se debe purgar ???

@FelixDanGarasiAuto 2 года назад

i let the system burp after topping up.

@gibsonindistress418 5 лет назад

I tried to bleed the system after changing the coolant. When I did, the coolant just started to overflow the radiator cap so I turned the car off... Is this normal?

@FelixDanGarasiAuto 5 лет назад

Yeap its normal. Let it over flow for 10 mins until both fans kicks in. Then after that just top up the coolant until full & dont forget top up the overflow bottle too. Rinse away the spillage with clean water.

@Lotrioni 4 дня назад

This video is wrong in so many ways. If you do this you drain only half the coolant. The rest remains somewhere in the system. This procedure is not complete!

@FelixDanGarasiAuto 4 дня назад

@@Lotrioni Then would you kindly tell us how? as specifically im not doing a full system replacement on this video. 🙏🏼😁

@user-ie9nd3ow1y 4 месяца назад

Охлаждающую жидкость слили только с радиатора и расширительного бака, порядка 2,5 литра старой жидкости осталось в отопителе и патрубках системы.

@FelixDanGarasiAuto 4 месяца назад

it should be more than 2.5L comes out from the system.

@user-ie9nd3ow1y 4 месяца назад

@@FelixDanGarasiAuto Вся система вмещает порядка 7L, вы слили только около 4L

@FelixDanGarasiAuto 4 месяца назад

@@user-ie9nd3ow1y yes this video is not about draining the whole cooling system. To fully drain you have to disconnect the lower and upper hose and you can drain the whole from the block. But if you repeat the drain and fill every 2 years your engine should be fine and you are not wasting too much effort on this particular service.

@user-ie9nd3ow1y 4 месяца назад

Зачем мешать старую и новую жидкости? Не так сложно слить максимально все.

@FelixDanGarasiAuto 4 месяца назад

@@user-ie9nd3ow1y Im not ocd about it and at the time its not neccessary to do a complete coolant drain for this video. The car is completely fine until now. Just do a regular drain n fill every 2 years or so. you should be all good to go.

@dalevannguyen157 Год назад

I Think The Bottle Better Than The Fluid 😂😅😮

@FelixDanGarasiAuto Год назад

😂😂😂😂

@eddiev6013 4 года назад

The car has 30k km why would you mess with it. OEM coolant is easily good for 100k

@FelixDanGarasiAuto 4 года назад

The purpose of this video is to show and help owners how they can do it themself. I already know the coolant is good of 100k. Maybe if you like you can replace yours at 100k using this method. :)