Replacing axle bearing and seal on a GM 10 bolt 7.5 inch differential

Подписаться 247

Просмотров 106 тыс.

50% 1

This is just 1 part of repairing a GM 10 bolt 7.5 inch differential. The spider gears or mini spool needs to be partly disassembled and C clips need to be removed in order to get the axles out. Then you can replace the axle bearings and seals.

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 65

@firefighter3072 4 года назад

Can't get any easier than that, simple and direct without a word said . nice job thank you

@jerryturensky 3 года назад

You're welcome!

@joepawlu9523 2 года назад

@@jerryturensky what is the part number for the bearing and seals. Thx I can't find em anywhere I got a gm 10 bolt 3.23 gears and a 26 spline thx

@jerryturensky 2 года назад

@@joepawlu9523 I found the part numbers in Rock Auto, sorry I don't have the part numbers, it was a long time ago.

@AeroSS87 Год назад

@@joepawlu9523 I'm a bit late here, but I ordered FAG FC67147. German company. Really good quality. Unlike the Chinese BCA stuff these days.

@fultonguyy Год назад

Like your quick to the point video, having to do the same on 2000 blazer, glad to see you put wheel bearing grease to lube the bearing another video use lucas, but wheel bearing grease is the way.

@nonyadamnbusiness9887 8 лет назад

You left out the part where you have to buy a kit to extract the broken retaining screw in the differential cross shaft before you can pull the C-clip and pull the axle. Nice video of the last steps. Doing it right with proper driving tools.

@willmills1370 4 года назад

Yup, mine broke too. Got the extractor kit from Summit Racing. Yukon Gear and Axle makes it but doesn't sell it to the public. I watched CVSahara his video on RU-vid on replacing that dam Pinion Retaining bolt, I bought two more from Autoplicity for my '79 Trans Am, it came in yesterday. Ain't got nothing else to do with this COVID 19 lock down.

@dtuck0509 4 года назад

Straight to the point, great video.

@jerryturensky 3 года назад

Thanks

@dang_industries 2 года назад

Great video! Easy job but I came here to confirm how deep the seal should end up (looks about 1/8” past flush)

@jerryturensky 2 года назад

I pressed it in til it stopped

@MrDeepwatermarine 5 месяцев назад

I came here to find the attachment for my slide hammer you’re using

@Bacon676 6 лет назад

Fantastic fucking video. Short, simple, right to it. Just what I was looking for.

@sugargoldy 5 лет назад

Good video thank you I needed my memory refreshed

@FromThe3PointLine 7 лет назад

thanks man this was helpful to me in houston tx

@FromThe3PointLine 3 года назад

@Marc Owens OK kid

@dustyhinton7639 4 года назад

Do not do that with your axle shaft the bearing puller will slide through the seal if you can pop them both out at once

@Boz_-st4jt 2 года назад

Not sure I'd let this guy touch my 01 2500 HD? Much less change the oil! Was astonished he would use the axle splines to remove the seal!

@jerryturensky 11 месяцев назад

Cause racecar

@jasonlewallen7146 6 месяцев назад

@@jerryturenskyfreaking out about popping a “seal” as you did. They’d stroke if shown the other things folks do on race cars. 😂

@oldbiker9739 2 месяца назад

@@Boz_-st4jt its just a seal they been doing that since they started with rawhide seals

@gza06955 7 лет назад

Thank you Jerry

@ralfhinojosa 4 года назад

Thank you for the video

@stephengrant2677 18 дней назад

mine came out the hard way, piece by piece. this is just too easy

@HectorMartinez-fq6cy 7 лет назад

Real helpful, much appreciated.

@bellingsen 2 года назад

How can I tell it`s a 7.5" or 7.625 inch? I have this 1999 pontiac firebird trans am v8 convertible. I had some differential issues and ordered bearings for 7.6". Problems! I think it`s 7.5" . What is the difference and where can I find the right number 7.5" or 7.6"...?

@oldbiker9739 2 месяца назад

the 7.5.or 7.6 10 bolt has sharp horns on the bottom rear diff casting . the 8,5 has a square casting at rear housing .

@oldbiker9739 2 месяца назад

hers how you tell , ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-zcYumTo9baw.html

@cheflewisanthony4685 4 года назад

If that's bad will it make a loud thump noise

@mikeb6902 Месяц назад

would I be correct in assuming when you are driving the bearings in, when you hear a change in sound, that means the bearing is fully seated? Thank you.

@jerryturensky 19 дней назад

@@mikeb6902 yes that has been my experience. Thx for the comment.

@isaacwashington9925 8 лет назад

great video. thanks!!!!

@wilsonwichman4847 Месяц назад

Does the axle just pop out ir do i need tk remove anything

@IsleOfFeldspar Год назад

Does the gear oil lubricate that bearing too? I’m not a mechanic.

@jerryturensky Год назад

yes it does, that's why its important to have the right amount of gear oil in the differential.

@WilliamYaughn 5 месяцев назад

Who ,akes that tool that he is using to drive the bearing in?

@jerryturensky 5 месяцев назад

Harbor Freight

@stephengrant2677 20 дней назад

The axle is half the bearing surface

@jerryturensky 19 дней назад

@@stephengrant2677 thx for the comment

@jays4forces 7 лет назад

what bearings did you use BC for whatever reason...I can't seem to find any for my 87 cutlass..7.5

@efarley164 8 лет назад

What tool are you using to pull the bearing...it was so quick. We've tried several brands of bearing pullers for our 1970 Chevelle and none work.

@wll1500 5 лет назад

He literally just used the axle lol

@austinmouw3383 4 года назад

@@wll1500 He asked about the bearing, not the seal.

@wll1500 4 года назад

@@austinmouw3383 erm.... The bearing just comes right out with the seal.

@austinmouw3383 4 года назад

wll1500 I think you need to watch the video again. He uses a slide hammer to pop the bearing out

@wll1500 4 года назад

@@austinmouw3383 welp fuck, I just made myself look like an idiot. I thought this thread was from another video about a trailer hub...

@daviddejesus7037 11 месяцев назад

Where did u get the puller bud ?

@jerryturensky 11 месяцев назад

Fee tool rental O'reilly auto parts, Phoenix AZ

@dakotawelsh5709 3 года назад

Does anyone know where you can get that tool to put the new bearing in?

@mr.nobody68 2 года назад

Use a large socket

@jerryturensky 2 года назад

Harbor Freight

@veggiepowered 4 года назад

Is That A G20 Van ?

@jerryturensky 3 года назад

1986 Monte Carlo

@but199018 8 лет назад

What's the exact name of the tools you were using? (Drive tool and puller)

@jerryturensky 5 лет назад

Harbor Frieght tools

@nobullshit9721 4 года назад

jerryturensky lol 😂 seemed to work pretty well overall tho

@jayme8614 6 лет назад

I'm wrong it's not spring should be twards the oil my car was installed wrong from the factory

@79monte 2 года назад

Dude say something tell me which way the bearing supposed to go in that's what I'm looking for because it does matter and you're just sitting here quiet as mouse

@jerryturensky 2 года назад

I made this video to show friends I work on my own race car, hope this video helps, cause I did not show removing the axles.

@jayme8614 6 лет назад

Seal is in backwards!