Replacing Hay Rake Teeth!!! 

Always nice to show that not everything lasts forever. You would think there wouldn't be much wear on the rake but if you have uneven ground it can really be hard on them. Thanks again.

It’s great to hear from Shaun! Lol great video thanks for your time and effort to post these videos

Love how you keep bringing Shaun into the videos! 👍

You bringing Shaun into whatever century this is kicking and screaming....He just wants to be left alone.....with the Dog

Not a fancy video, but real. I always enjoy your videos. Also good to see Shaun.

You will need all the extra teeth to roll up that heavy alfalfa crop you knocked down last video. Good job Tyson and Shaun, keep the great videos coming.

I tried changing some by my self and it was way harder. It cleans up way better with most of the teeth on it. Thanks for sharing 👍🏻

Good video Tyson like it and your help too .

i remember changing them they are a pain great video tyson thanks

Nice repair and video.

Shaun is a man of few words! LOL Nice job on the rake!

The broken ones make awesome tent pegs. Never have to worry about running out as long as you use the rake.

Good day Boy I had to laugh out loud, when you ask Shaun if he had anything to say ''not a dam thing''. But at around 8 mins. I noticed the hay rake inspector was there Fred & Barney & Shuey? Thanks.

You could weld a thick washer over the oblong hole to make it round before installing the new teeth to help. Thx for the video!!!

we used to drill new holes between the old ones, its tough to drill but on a drill press and a good bit its ok

We used to protect them against rust before storage. Giving the wheel a swing and spray Tectil or undercoating on the ring, filling the holes . Looks you did that too on 1 wheel ?

In order to keep the elongated holes from breaking more teeth could you add a rubber grommet of some type. Easiest way for that might be aerosol rhino liner. If need be accelerating the cure time with a heat gun or torch. Both sides of the ring and both sides of the wheel

Man Shawn is a chatter box. Lol. Thanks for the video Ty.

Shaun just gettin after it!

O boy.took me a while to get good at changeing them.had still have old vicon rake.gehl teeth fit it.last year bought new sitrix 10 wheel.

Flaman has 12 wheel Sovema Cropmaster for about 15g, had ours for 15 years now, can't complain

Too bad we all didn't have a hand like Shawn, you're lucky to have him for sure. Though somewhere I seen a video that was mentioning that it was better to run worn teeth together and new teeth together.

Looking good Tyson, when do u think you'll start swathing canola

Changing rake teeth is one of my lest favorite jobs around here, but it has to get done.

I went to buy 28 teeth and for the cost it was cheaper to buy the whole take wheel and use old ones for replacement on future broken ones...new Kuhn 12 wheel is about 9000 bones...

Like your videos. I am glad that it's you changing teeth and not me.

What worries me is that broken sections laying somewhere in the field, what will it do to your baler

got a question for ya. lol. where or what field would u spread ur pile of manure on? like the field, where u just made hay off of? or on a field, that has grain on it. wanna see ya attacking that pile u got stored. ha! thanks for video. i watch em all-just never comment much-ok. probably the best-huh

I don't know about you but I think Shaun is just way to talkative. LOL. Thanks for the video.

How is he at lacing Spoked rims?

What kind of rake is that.teeth and plates and bolts that hold teeth exactly the same as my vicon. Just walked out looked at my 2016 sitrix.same. paid 6300 new 10 wheel.with a center wheel.fall of 2016

Does Shaun talk when the camera isn't running ??

That's Shawn is a real Chatterbox

The way to fix those wheels is have a machine shop make you a bunch of metal slugs with a slight edge on them just a bit less than the diameter of the wheel. Have them drill a hole dead center of the slug or plug as would be in a new wheel or the diameter of the rake teeth. Then you drill out the hole where the broken rake tooth was to the diameter of the small portion of the plug the machine shop made you and tig or skip well it in, and bingo, a hole that can be fixed over and over again. If you used two drills, the second drill should hold it's diameter by a few thousandths of an inch, giving you a good fit of the new inserted plug, or send away and buy a reamer about .005 bigger than the small portion of the plug the machine shop made you.

I found it easier to put the teeth in from the other end with the small hook going through first. Easier for me just a suggestion

what brand rake this r？thx

mixing new teeth with old ones that are worn can cause the new one to break as its longer and then take more stress. put new on one wheel and take the worn and use on the others :)

54 teeth missing, gotta be getting close to a record on a 10 wheel, good eye and fix,

What was the temperature there when you made this ?

I work for a farmer that says changing the rake teeth is a 1 person job how ? When clearly this shows 2 people doing it

Since this is such a ass aching job which causes lost time in the field. To improve turn @ time OLF has a few of these rebuilt and ready to go. Replace the entire wheel and keep raking. You can replace individual tines when weather keeps you off of the field

I had a lot of trouble replacing tines, hope I don't do them again

we used this kinda rakes 160years ago on my dads farm

Hinice

The broken hay rake teeth out in the field might puncture your tractor tires

I just buy the wheel new with teeth in it!!! By the time teeth are shot, so is the wheel from slotting.... not that high down here!!

You know you can buy the whole wheel for less than a $100 from Rural King. For those wheels you said were really worn out.

I get a feeling Shawn is tired of your damn videos......I'm not keep em coming.

That looks like a tedious and pain in the ass kind of job! lol

Definitely not a one-person job!

If you just loose them nuts to the end of the bolts you should be able to slide them teeth in and out without taking the plate right off. One man job i do it myself all the time with my 3/8 milwaukee cordless impact. I hate to say but i think i can change them faster than both you goin at it. Unless your rake is different....

You really are a long tall skinny drink of water

You need to buy Shaun some long pants ....getting to be to big for shorty pants...long pants are easier on legs