Resaw Basics - Bandsaw Your Own Veneer

Подписаться 2,2 тыс.

Просмотров 13 тыс.

50% 1

In this video, I show you the basics of getting started with resawing your own lumber on the bandsaw. Using a jointer, table saw, and a bandsaw you can create different dimensions on your lumber easily by following a few steps. This allows you to create your own shop sawn veneer, make stock for bent laminations and simply breaks down large boards to more manageable sizes. I use a Laguna 12" Jointer, Sawstop ICS Table Saw, and a Powermatic Bandsaw in this video. Micro jig push pads, Jessem stock guides, and a feather pro feather board.

Хобби

Опубликовано:

19 дек 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 26

@imlew7853 7 месяцев назад

Your video is a life saver to many. Tons of mistakes for lack of experience will be eliminated. With the tough economy, resawing boards with some good imagination for creativity produces more from the money spent. THANK YOU .......... well appreciated.

@jameswesleyfurniture 6 месяцев назад

Glad it was helpful! Thanks!

@pmelchman 2 года назад

Very thorough James. Lots of great tips. Thanks.

@jameswesleyfurniture 2 года назад

Thanks again!

@deanaldinger5018 2 года назад

Another well done and informative video

@jameswesleyfurniture 2 года назад

Thanks, I appreciate it!

@Transcendental9 Год назад

This is a great video, thank you for sharing.

@jameswesleyfurniture 11 месяцев назад

Glad you enjoyed it!

@mikedisimile2478 Год назад

Thank you very much. You did a great job explaining everything 👍

@jameswesleyfurniture 11 месяцев назад

You are welcome!

@horsetowater Год назад

It's beautiful. Thanks for sharing. I was initially wondering why you had a bandsaw with a 24inch??! DoC then you showed off some of your lamination work. Amazing.

@Nissan300zxshowcar 2 месяца назад

Great video! Question, without a drum sander, how would you recommend sanding the resawed veneers?

@johnbies7041 3 месяца назад

James, help.. I dream of building a Sam Maloof Rocking Chair… Question: where does one get a copy the plans for such a rocking chair?

@jasondarr5911 2 года назад

Great job. I wonder if you ever encounter what I always seem to encounter? I am primarily re-sawing ash. And when I do, the boards both cup away from the blade creating a huge gap between the boards. So if you try to put them back together, i have a huge gap in the middle… So if I am splitting a 2 inch thick by 8 inches tall board for example, I can rarely get anywhere near 3/4 after rejointing and planing because of the cupping on both pieces.

@jameswesleyfurniture 2 года назад

I find that boards always nice to some degree but it really comes down to the drying process and how fast it was kiln dried. Too fast and the center isn't fully dry and immediately starts to dry after cutting and the internal tension being released. Crazy grains can get into this issue fairly quickly as well. If you can source it air dried material that is finished in a kiln is a great place to start with if you are going to break it all down by resawing

@jasondarr5911 2 года назад

@@jameswesleyfurniture thanks bud. Appreciate the reply

@highlandp 2 года назад

This has been my problem too -- learning how to work with thinner wood -- 1/4, 5/16ths for small boxes and such. I've tried resawing, but my boards end up so warped and I have challenges re-milling them to something usable afterwards. Would love a video about how to avoid this!

@allansalzman1072 Месяц назад

Do you adjust for drift with the fence?

@joem6859 2 года назад

Do you ever have issues with blade 'drift'?? Very nice bandsaw, like the guides, heavy duty. Nice blade too. You should talk a little about the blade you're using.

@jameswesleyfurniture 2 года назад

Defintely could go into further detail. I use a Laguna resaw king and in my experience the tension of the blade and the widest blade width you can get help control some of the drift that can occur

@joem6859 2 года назад

@@jameswesleyfurniture yep, the laguna blade might be the best, a little pricey too. I just started bookmatching chunks of maple for guitars.... can be challenging