Resin Skull - Snowglobe effect using glycerine water, Micapowder.  

Oh sorry, I am always worried that my videos would be too long. I will make sure I add more detail in my next videos. What were you looking for? Do you have any questions? 😀

Hope all goes well for you. Happy this could help 😄

Thank you 😊

Haha crazy isn't it, I love crafting but I need room to do more lol Hopefully want be too long before my Resin and Jesmonite creations are back 😍

Thank you so much.

Thank you so much 😊

I would love a separate space to create. Hope you are able to sell some of your creations on also and help with space 😀 Thank you x 😊

Thank you so much x

Thank you so much, me too. My favourite so far 😍

Thank you, 😊

Thank you

Thank you so much, this is the result I was looking for. I will use this technique for any future snowglobe skulls I do. 😊

Thank you so much. They were the 6cm one, although they are currently out stock. www.amazon.co.uk/dp/B09G3HBTRF?ref=ppx_pop_mob_ap_share

Thank you so much, the best one yet 💗

Thank you so much!

Thank you so much 😊

Perfect, of course recreate. I love sharing videos in the hope of helping others to do the same. If not better xx Thank you 😊

Thank you very much 😊

Hello apologies for not replying sooner. I did not weigh the liquids. I kinda went with a 20 / 80 mix. 20 being water. But I kinda mixed a little and a time, until I was happy with the movement 😁 Hope you get it right for you.

I use half water half glycerin

I think it all depends on what you use. But normally cling film can withstand some heat. As I used to over food when heating in the microwave.

You don't need to use any cling film the ball can go right into the mold without it. Also the bauble can sit right into the cavity without any sticks or having to balance it. My friend makes them all she does is coat the bauble in some resin once bauble is filled pour resin half way up mold let it cure. Once cured she brushes the cured resin with mica then pours the rest of the resin to the top.

I put glycerin quarter the way up in the bulb and rest water. Then mixed. unfortunately I did not actually measure the volume, which I should of for next time 😃 Hope you figure it out for you. although volumes may change, to what you are adding to it. Eg Mica, glitter or ink xx

The skull was about 5 6 inches in depth. It is a mold I got from Amazon.

I sealed the bubble with a cling film and resin glue. 😊

I sealed with clingfilm and a Gorilla branded resin glue. Thank you 😊

@@smurphyart-love2create268 thank you for replying and thank you for the information this is such a great idea I can't wait to try it :)

I think I just poured and added water a bit at a time until I got the right viscosity 😀

So sorry for the delay, have been away for a while due to new job and career change. I am S Murphy Art on Instagram also.

I would also like the video please 🙏🏻

I still can’t find this snow globe part of the video tutorial. Instagram you mentioned that the visto is on “mh channel”. What and where is that? I feel like I’m chasing this video all over the internet.

Right?

​@@leannharris5854 I think I figured out how to seal it. Cut the top off tje ornament. Lime the edge with UV resin and put a clear, plastic piece over the top then use a UV light

Apologies in the delay, I have been working so much and been away from my channel. The ball is 6mm. It is a Xmas bauble 😊

@@smurphyart-love2create268 ❤️ awesome thank you so much for helping me. There's no need to apologize your a busy lady . I hope you have a great day and weekend coming up. And get some rest

I used the letsResin resin (not a deep pour specifically). This was completed in two takes.

Yes baby oil would work just as good. Easier to get hold of also ☺️

I think it is the 5mm bauble I used. It fits lovely in this mould.

6mm, it is a Xmas bauble. I purchased a pack of 12 from Amazon. Thank you 😊

It was the 6 cm one I believe xx

I got mine through Amazon x I hope you managed to give it ago and it turned out beautifully.

Sorry it is a baubuel, they hang on your Christmas tree. 😊

The plastic one suspended better I feel. I think glass would be heavy. But, it may work the same. I have not tried it myself. If you do, please share your result ? I would be worried, if it was dropped 🫣