Retraction Tuning - Calibrating your 3D printer Part 7- Ender 3 V2

Подписаться 3,3 тыс.

Просмотров 19 тыс.

50% 1

This video is part of a series of 10 videos that go through how to properly calibrate your 3D Printer, the videos include:
Calibrating Your 3D Printer Overview
Part 1: Frame Check
Part 2: PID Autotune
Part 3: First Layer (Advanced Bed-leveling)
Part 4: Baseline Calibration Cube Print
Part 5: E-Steps Calibration
Part 6: Slicer Flow Calibration
Part 7: Retraction Calibration
Part 8: Temperature Tuning
Part 9: Acceleration Tuning
Here is the link to Teaching Tech's Overview:
• 3D printer calibration...
Huge credit to Teaching Tech for making the following website which is one of the best guides I have seen to calibrating your 3D printer step by step. This video is part of a series of videos going through each step of that process. Here is the link to the website:
teachingtechyt....
Check out the playlist below to watch the other videos in this series:
Calibrating your 3D printer
Music by Byron Craft
Free Rap/ Beats | New Rap Instrumentals | Freestyle Instrumentals
• Free Rap/ Beats | New ...

Опубликовано:

28 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@sketch088 3 года назад

Thank you for your videos. They have saved me from pulling out the rest of my hair lol. I really appreciate it. I installed a microswiss on my ender 3 v2 and it has been issue after issue. But thankfully your videos have helped with almost all of them.

@rainmaker3d 3 года назад

I'm glad they helped!

@mochosla 8 месяцев назад

These are some amazing videos! Will these steps work on a Gigabot 3+? We are having printing issues I need to fix.

@carterandrews1275 3 года назад

Dude this is Carter from Astate, you literally inspired me to get into 3D printing and now I finally have one of my own and I’m learning from you again on RU-vid 😂😂 I was like damn his voice sounds familiar

@MaximilianBecker87 5 месяцев назад

hey! is that github page offline?

@JeevaDotNet 2 года назад

i got refraction on all the layers from 4-9 :( eSUN PLA clear, 200'C, 55'C bed Ender 3 v2

@crazykayzee845 2 года назад

are there similar websites where we can get a gcode made to test these things ? the website in the video no longer works

@nrich5127 8 месяцев назад

I had an obscene amount of bumps then I adjusted Retraction Distance from 6 to 8 and it was reduced 90% I'm now going to go through all your videos to fine tune my Ender 3 Pro. Thanks for the info.

@ouroborossoluciones629 3 года назад

Hello my friend, I have made the impressions with the gcode and it works well for me, but I cannot configure my cura to achieve good quality impressions, maybe some advice?

@scyther149 3 года назад

i have the same problem, i put the same configuration in cura but don't work

@TheMoody876 Год назад

I'm having a problem with speed and max flow Tuning on the website the g code generated has multiple stops instead of being a smooth vase mode

@kloakovalimonada 2 года назад

What's that gorgeous silver filament?

@Ideatronic1 3 года назад

GOOD

@nan00k86 3 года назад

thanks for this, so i went through this with 2 different brand pla as the first one didnt seem any difference in the segments, and the second one seem to get worse at the top, so i guess my printer is good with the default settings.

@jasonchristinablanton3482 3 года назад

Hi I went through your steps on my Ender3v2 and had very little stringing but had a very bad line going up both towers where the string would come from at each layer. It is pronounced more on the right tower than left. Is this a cooling fan shroud issue? Any other settings to work to correct this? I believe its called a z scar and it looks like even your tower has some as well but mine is more pronounced and feels quite rough. Thanks!

@rainmaker3d 3 года назад

Hey Jason, good news on the stringing bad news on the Z scar. I will do some more research on my end. One setting to tinker with would be your layer start and stop. If the Z scar is coming from the start of each layer you could randomize it so it doesn't stick out as bad. Do you see this on other prints that you have or just the tower?

@bethanybellwarts 3 года назад

@@rainmaker3d Mine also has this exact issue, zero stringing on each layer, but a really bad zscar on the right tower. my other prints seem fine though.

@LOLgarena 3 года назад

thank you for your video. Is there anything I need to do since my first layer ain't sticking with the bed for all the gcode? Do you slice it in cura first? But from other gcode bed levelling (chep) it work like charm.

@rainmaker3d 3 года назад

Is it just the retraction tower that is not sticking? First layer adhesion should not be a gcode issue. How do your other prints stick? You may try a glue stick if you think your bed is level and your nozzle is close enough.

@LOLgarena 3 года назад

@@rainmaker3d nvm, I think my eprom is the source. Reset it and it's good to go. Thank you again for the videos. Subscribed.

@rainmaker3d 3 года назад

@@LOLgarena glad you got it figured out. Thanks for subscribing!