Even though this is from 2012, it is still relevant. As an old retired military guy I must say even a private cannot mess it up with the block of instructions you just demonstrated. Outstanding.
Your series of reloading videos are the clearest, simplest and easiest to understand sets of instruction for manual reloading on RU-vid. You voice and answer pretty much every question as it comes up in my own mind. You assume nothing about the viewers experience yet never condescend. As a novice reloader I can’t thank you enough.
Thank you so much for the very kind words and support that you give my channel. I've read quite a few comments today and yours is the best one so far! Blessings from Arizona my friend!
Excellent! Clear,exacting,and comprehensive lesson for the rifle die setups.I am brand-new to ammunition reloading so really needed this feature! Your demonstration of the process of resizing,seating and crimping leaves me certain I can now easily reload my 5.56 caliber rifle rounds.Other videos brush through the process too rapidly,but you are spot-on for beginners like me.THANK YOU!
Love the Lee products. Simple and effective. I have loaded countless thousands upon thousands of 223 and 9mm since the 90s with this setup without a failure.
Thank you for your interest in my channel as well as you're comment... It's good to know that some of my work helped get you going... Merry Christmas as well and you're right. Jesus lives indeed... :)
Just started reloading, literally last week. This video helps with the crimping process. You explained it in a much easier process than any book I have read. Thanks for the education.
No worries. Crimp in a lever action is needed because they were originally used as saddle guns and took a beating. The tubular magazines had the possibility for the rounds to slam against eachother while the gun is being moved around. Some semi auto's have very violent recoil and this is why some "additional" case mouth tension or crimp is needed for them. I hope this info was helpful. Have a good evening! :)
Thank you for the kind words and all the support you give my channel! If you're loading for a single shot or a bolt action a crimp isn't always needed. During the re-sizing process on the downstroke of the ram the expander ball re-sizes the case mouth diameter. When you seat the bullet, theres plenty of case mouth tension to hold the bullet firmly in place for most applications. I usually only crimp for semi-autos and lever actions. I hope this info was helpful. Have a great day! :)
I've been reloading for 17 years now. And let me just start by saying wow, what a very well made video. Now the crimp feature I've never messed with but it was nice to see how to and what to use it for. Great information and great video.
Ten years on and still as relevant as ever. Nice clear and concise. I hope life has been kind d to you pal. All the best for the New Year, here in 2023. A fellow shooter from over the water here in the UK 👍 🇬🇧
Thank you! Yup, she's bent. I have also broke a few over the years. I keep a handy supply of them on hand. I like to tumble and then de-cap. Maybe I should try it the other way around and see how that works for me. I'm just not too excited about getting media in my flash holes. Thanks for the support to my channel. Have a good evening. :)
I would recommend determining proper lenght of cartridge by establishing the bullet being .005 - .010 from lands before locking seating depth. That has worked best for accuracy on many rifles for 30+ years.
I know this is an old video but just got this press and have started to reload this video has helped so much thank you for sharing your knowledge much appreciated.
I have watched several demos of how to use a bench Lee reloader die an I'll be clear. I watched several Lee classic loader vids and it got me started on that kind of reloading. Whether simple or not, they were straight forward and easy to follow. Think of it as I just got a bench reloader and I have no idea what to do is that a Hurst shifter on the end or what? A big part of teaching is empathy. If you ain't got it you can't get it. Ok what do I do first..... That's called a..... This is called a....... Here's how you... Just my two cents. Everyone is not conversant. Bruce
jiujitsu2000 I did every thing you did and it worked, I seated the bullet just like you said but I used my crimping die. I crimped my 223 with a mild crimp. This worked . Now every bullet I seat is seated correctly. I have your videos on a disk so when I need to reference your procedure I know I can reference when I need it. Great videos.
You're welcome and thank you for your kind words and support to my channel! First thing that I'd recommend is to make sure you're trimming your brass. This should fix your problem. If it doesn't, I'd recommend backing out the bullet seating die body another turn, counterclockwise. This will take away the crimp feature of the die. Don't worry too much about the crimp because the case mouth generally has plenty of tension to hold the bullet for most applications. Have a great day! :)
Thank you for the kind words and the support that you give my channel. Single stage presses are nice! Reloading with someone is always nice too. Good time to chat, good quality time! Then when it's all done, you guys can shoot together. Have a good day! :)
This video takes all the unknowns out of setting up your reloading press. I have a multi-stage RCBS and I will have to check to see if the crimp is a feature on my press die. I have a factory crimper so it doesn't matter. When I started I had little information about how to setup a press. I have many crushed rifle necks because of improperly adjusted die setup. This is a wonderful video. I have this link set in my favorites. Another helpful tip would be to include with this video setting up a factory crimp die. I am not sure how much pressure the crimp should take and not damage the bullet. This video takes all of the guess work out of reloading!!!! Thank you.
JJ You have the best Reloading instructions on RU-vid Easy to understand & Explained in simple detail etc. Thanks again, For taking your time with these lessons etc.
I just set up my 1st reloaded today. I turned out 50 nice 500 Smith Mags and they shot great. I'm starting 300 Blackout tomm and this video really helped me figure out how to set my dies. thank you.
I really like your reloading videos. As I started getting into reloading your way of explaining and demonstrating was the most helpful I have found. You do a great job of explaining the process, and in a way that makes sense and is follow able. Thank you.
A very informative video. I just learned a lot about a two-die set and how to properly set them up and use them. Also, on how to use the length gauge tool. Thank you very much.
Sounds great! Thank you for the support and kind words! I've been thinking of getting a new single stage press as well. This is such a fun hobby. I'd love to see your vids. Have a good evening. :)
Thanks to you my Lee single stage press just arrived. Now I'm waiting for my 223 2 die set with shell holder. I was thinking of getting a tumbler but I've seen many good videos on sonic cleaners for my brass. I can't wait to start my winter hobby! Cheers man! I wouldn't be reloading without all your great tutorials.
Great video. As the previous comment, you would be a good trainer - you are detailed, concise and demonstrate a patient nature that is helpful when instructing others.
Three die sets are necessary for straight walled cases, and sometimes are a full length sizing die, neck sizing die, and seat/crimp die. If you're loading for a semi auto and a manual action, a 3 die set with neck + full size die is for you. If you're loading cast lead in a straight walled cartridge, you're looking at sizing, expanding, belling, powder dropping, seating, and crimping. You're looking at 4 or 5 dies.
Thank you, for all the free info you give, After watching you show all kinds of reloading videos, I am looking now for a single stage press and the other tools we will need, Thanks again for your replies, To my questions, I cant wait to start reloading with my oldest son, Thanks again Brian.
Good morning. There are several manufactures that offer a case length gague. I have some by Lyman, Dillon, L.E. Wilson. They all do a great job. You can find them online at the Dillon website, Midway, Sinclair, Brownells, etc... They usually run around $20-45 depending on what you get. Most of mine are Dillon and Lyman, but honestly, they're all good in my opinion. I hope this info was helpful. Thanks for watching and have a great day! :)
Great video. THE PROCESS IS IN ERROR. When setting up the resizing die, it needs to be screwed in 1/4 turn, tightened and locked. Otherwise not all rounds will chamber in the rifle (even if they pass gages). Also, DO NOT crimp. It is unnecessary, not recommended by Hornady and will potentially cause chambering problems if it is excessive. Before you load with powder, I highly recommend setting bullets on about 10 to 20 shells and try these dummy rounds on the rifle. See if all chamber. If so, then proceed with powder-loading the rest.
nice video, detailed and explained well. to crimp better and once the tool regulates, it is enough to turn the casing of a quarter of turn and to crimp 2 more times. Setting becomes more equilibreted on the circumference of the bullet ( clem from Paris)
You Sir, are an excellent teacher. I've learned so much from you. Thank you so very much. I'm implementing your flow from de-capping resizing ...on. Only because I have a sonic cleaner and it does a great job for me. Thanks again!
jiujitsu2000 My friend you are a natural born teacher/instructor, I can say that because I have watched two or more videos and I have yet to hear you say ah, or you know, or any of the staling tactics you hear a lot of people use, mighty fine job. Keep up the good work. Easton Ford 10-5-15
Thats awesome that you got your press! Whenever I'm expecting a package I get all excited... It makes me feel good that you said my video's helped you get into reloading. Thanks for your interest in my channel and feel free to subscribe if you haven't already. Have a good day! :)
This one's an old one but thank you for stopping by please feel free to look through all the videos on my channel I have tons of playlist as well as over 1,300 videos
jiujitsu2000 I did every thing you did when I was seating my 223 it worked like a charmWhat I have say is don't use any Winchester 223 FMJ Boat Tail. I found that the bullets were not the same size. I had to size each bullet when I found the right size every thing worked just like you said it would work. I have put all of your videos in my favorites. I use them for reference. I would say your the best on the Internet. Keep up the good workErnie
This is great. I was having some seating issues that led me to watch your other video, but this explains the die setup perfectly. Since I came across your channel, I am learning more about reloading, making soap, building tripods, etc. You have a great style in your videos that comes across very geniune and real. Thanks again.
Thanks for the video!!! I'm new to reloading and this was the best video I've ever watched, hands down!!!! Thanks for taking the time to do this for us... and Indeed, Jesus lives. thanks brother
Best tutorial I have ever seen and I have watched many. Very educational very helpful appreciate your teaching tactics thank you so much for using step-by-step instructions for us laymen
Generally speaking, You only expand the case mouths on straight walled cases. Something like the 45-70 would often need this step. Have a great day! :)
Jiu your instructions were Great.? I bought a Lee Hand Held Press to load with till I set up my Bench.? & a set of Hornady Dies in the Rem 223.? Your video made it easy for me to set these Dies up & it worked out Great Thanks again for sharing your Video.?
+jiujitsu2000 Thanks again. Trying to get some Coyote load ready for my new Marlin XL7 Rifle.? Also picked up one of those FrankFord Small Scales on Amazon.? For about $30.00 Saw some great Reviews on it on the tube.?.
great video, I was going to just do full length resizing and then use Lee hand loader to finish, Primers I do by hand primer, but now I may attempt to try it all, now I get it. Reloading only for Mosin and 30-06
Really good presentation ...good use of tripod for your camera...plenty of light...also liked the use of a pointer to show small details.Excellent video! Narration is flawless, Hope that others will use your teaching style. Keep up the good work with more videos!
I have watched a bunch of your videos and man, I gotta tell ya, I feel like a pro reloader and I don't even have equipment yet! Working on acquiring a single stage soon, just spent a bunch of money on .223 components, all I need now is powder and the tools. I'm working on my own wet tumbling system. I'll let you know when I get some videos up of my stuff. Thanks again!
Great vid everyone please note for the crimping operation your brass has to be the exact same length done by trimming or the crimp will not be the same on every round