No video :(

Roborock S55 | Error 13 | Mainboard fuse exchange | check description

Подписаться 1,6 тыс.

Просмотров 35 тыс.

50% 1

This method works for many Roborock models.
Please do follwing steps:
1. Clean power pads (vacuum & charger). Test the system. If does not work, go to step 2.
2. Check charger voltage. It should be ~4,2V without load and ~19,6V with load. If the voltage is correct, skip to step 3.
3. It looks like your fuse is damaged. Please replace it according to this video.
Fuse model: RUEF300 PTC 3A 30V
New fuse costs ~0,2 USD.
Other helpful video (for Roborock S50):
• [EN] Roborock S50 - Er...

Опубликовано:

21 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 33

@davidfiori3861 Год назад

In my S50, fixed the charging error by changing the main capacitor in the charger. 10 minute job.

@bm2088hp 8 месяцев назад

This fixed the Error 13 on my Roborock E25, thanks!

@TechDayEveryDay 8 месяцев назад

You are welcome;)

@tomaspalencia877 9 месяцев назад

Yessss it works. Thanks for sharing my roborock is back!

@TechDayEveryDay 9 месяцев назад

You are welcome

@bestcar6156 Год назад

Dziękuję Robrock s55 śmiga teraz super :)

@TechDayEveryDay Год назад

Proszę bardzo :)

@plawp69 2 года назад

I went into this with no soldering experience. When I took the bad fuse off, there were two reddish rectangles underneath. Are those solder pads? I removed those too and there was a metallic material underneath the red rectangles. Was the new fuse supposed to be soldered to those red pads?

@YZFMANIAC08 2 года назад

Nice job, thanks for explanation 👍🏻✌🏻

@pawelkdi 2 года назад

it works thanks !!!

@roberthajduk4409 2 месяца назад

Hi, what tools do you use on your wideo? How do you so easily separated the the fuse from the motherboard? I’m rather inexperienced in that matter and looking for some advice.

@zsoltkallos437 4 месяца назад

Hi Everybody! I have Roborock S5, and the charging is not working, the vacuum cleaner always come off form the charger. How can i find out if the charger is the problem, or the battery or the vacuum cleaner mainboard? Thx in advance!

@serpadre87 Месяц назад

Were you able to fix it? My S5 is driving me crazy

@serpadre87 Месяц назад

I was able to fix it, finally! I replaced the capacitor on the charging dock but didn't fix it. Then changed the fuse as shown in this video and that worked like a charm

@eshtrum 2 года назад

What is the liquid that you put on the bad fuse to take it out?

@iam5085 Год назад

Flux?

@bogdaniosip492 2 года назад

Measured the resistor and it shows 0.15-0.4 values. Jumped it with a wire just to be sure....stil have the same error...any help? Battery ang charging station measures where ok. Also switched the battery Frome and with a friend's robot and his work fine with both of them, mine gets the error 13 with both ones

@merlinchiodo8943 2 месяца назад

I first changed the capacitor on the charging station but that doesn't do anything, and after that i did what you did which was quiet a hussle (used another brand of a resettable fuse) and it the robot is finally charging again

@TechDayEveryDay 2 месяца назад

It is nice to hear that it helped you.

@q3bing 2 года назад

May I ask where did you get the replacement fuse in the US? Thanks!

@ryana42 7 месяцев назад

Where do you get a fuzz like this? How Do I know if it applies to the s7?

@marcocornell7310 2 года назад

Moin, ich habe das selbe Problem wo kann ich so eine Sicherung bekommen? Gibts irgendwo auch einen Schaltplan?!

@kabassa Год назад

I changed the whole motherboard and that didn't solve my problem, so i changed the charging base and then yes that was definitely solved

@jorgech.997 8 месяцев назад

Hi, temp of the air flow?

@Akerfeldtfan Год назад

Unfortunately that didn't fix it. will keep looking!

@Henrik229 Год назад

Hi I also have a error 13 problem with my robot. But mine charges. Once the robot is charged and i try to start it it just turns off. Once it restarts it starts to charge again. I tried a known good battery but the problem still prevailed. I also jumped the fuse on the Mainboard but it did not held. What could I try now?

@samashraf4587 Год назад

i have the same problem. have u solved ur problem?

@schr3ck3 Год назад

What are you using there to get of the old fuse?

@TechDayEveryDay Год назад

I'm using hot air.

@schr3ck3 Год назад

@@TechDayEveryDay with what device? And what is the liquid? And isn't there some danger because of the hot air and the parts close to the fuse which should not get broken?

@TechDayEveryDay Год назад

@schr3ck3 please check link from below www.google.com/amp/s/www.instructables.com/SMD-SOLDERING-101-USING-HOT-PLATE-HOT-AIR-BLOWER-S/%3famp_page=true