Rogue Tradesmen & Noisy Boilers..  

Thank you for watching and tuning in. I love reading your comments so drop them down below ❤

Great vid mate. Regarding the flushing job, you've done what you can, you've advised them as well as Vaillant, if they don't want to go ahead I'd do the same as you, leave it up to them. That soakaway though 🤣🤣🤣

Just a tip with the bearing plate/membrane... The red part comes off with a twist clockwise (opposite to the norm) and you don't need to take the screws off the fan unit usually.. just press the little red tab that sticks out to unlock..although maybe you did have to on this occasion to take out the broken piece ... another great upload as usual mate..

As the saying goes Dan.. beauuutiful… top job Dan as always. It will pick up buddy . There is only so much one can do. If the customer don’t want to spend the money then that’s their problem. ❤❤❤

Know what you're doing I'll give you that...thankyou for the lessons and keep going.

I'm not getting many jobbing jobs tbh, I'm getting a lot of bathroom and tiling enquiries but that's it To note, I'm not gas safe, just wet plumbing and tiling

Another good un Dan, plenty of finger action 😮😂

You’re an excellent heating engineer / plumber Dan - I hope the work situation picks up up for you quickly. Another RU-vid plumber was saying his work had recently just dropped off.

Was quieter than usual a few weeks ago but now I’m flat out with work luckily. Booked up until end of August at the moment. I do a fair bit for a builder though that keeps me busy

Flippy flaps 🎉 vaillant love a water quality check 😂

This time of year not much happening all round, You need to go on a holiday mate 😂😂 👍😎🤜

Ive noticed that column/designer rads tend to give off a lot of rust. I usually double up with 2 litres of inhibitor to be sure. I drained a boiler the other day and the water was ginger😵🤣🙈

Diversify into air conditioning, very easy to fit and great margins.

Great video Dan, hope you enjoyed those flaps, 😂😂😂, you know me , sewer mind, 😂😂. Need a video on how to solve water bang/hammer on pipes.

Condensate looks well installed with the soak away 😂

Thank you for another video buddy. Now I gotta feed the new born talk to ya soon

Very quiet, Unsual. July last year for me was in my top 4 of the year

The quietest June that I can remember

Been a while since we had any innuendos 8:25 😂

My works dropped off too mate. It’ll pick back up

I think the big problem at the moment Dan is everythink is so expensive people just haven't got any money it will pick up again but it's going to take a while so when you do go to jobs you need to be looking to make your own work

Another typical great video mate, look after yourself!

Another quality video buddy. Works definitely slower all of a sudden gorn from 7-8 jobbing jobs a day to 2-3 a day now

That Thermostat is a Salus it500. They are sh*t. It can be used as a dual programmer or just a thermostat. There’s a few common wires linking over. Should be easy enough to swap it for an Esi thermostat obviously two lol. Aux is normally dedicated to hot water. Keep up the great work 👍

Sites are very slow so there may be a lot of guys struggling

Good vid, im sure the best location for that system filter is after the underfloor and ch returns, but before the boiler? as it looks like the UFH by-passes it. keep up the good work tho :)

its weird mate....can be quiet for a day or two then its mad again

Did u try opening the air vent on that magna clean🤔 I’ve had a few stuck ones over the years and that has worked quite a few times👍

You saying 5 min drive 3 miles that would take me about 30/40 mins lol

People start getting worried to spend money near elections. Its always happened no idea why but that's how things go

whats that wee bottle affair you use to dose systems via rads?

DTG Plumbing? Is that Mr Heatking's alter ego?

🤘😎🤘🫖☕️🍪🎥👍👍