I'm with you cflmaior. I've watched many bench grinder resto's and this is the first one where there was no attempt to restore and or keep the original nameplate. As far as I am concerned the nameplate is part of the tool and without it it is incomplete and a failure to properly restore. Sure the thing looks much better than it did and you did a great job but again it's not complete without the nameplate.
Grate job sir , I just make a restoration like you on a hold bench grinder 1946 model 108 from (The Cincinnati ) compagnie 110volts 4.5 amps 1/3 hp 1 phase
U R putting new bearing in you didn't apply grease. on top you are hitting the new bearing with the old rusted bearing You are very smart restoration man. We are learning from you bro keep it up
Интересно, а ты с алюминия ржавчину снимал? да еще и под краской? и самое верное решение сделать из горючего материала дно в потенциально опасном для возгорания месте. Это лучшая реставрация после реставрация в стиле "случайно" найденных приборов на свалке.
بہترین.... آپ ایک سینڈ بلاسٹنگ کیبین بھی بنا لو.. بہت آسانی ہوجاتی ہے. آن / آف سوئچ نئے اسٹائل کا ہوتا اور ایک کلر کی بجائے دو کنٹراسٹ کلر ہوتے تو اے ون کام ہوجاتا..
Nameplate!, Cable Grommet, Earthing (Grounding), Shaft end float, and these are just a few essentials that were lacking. If I ever start restoring anything to this standard, just shoot me...
This video makes me look at the word restoration a bit different. In other videos I see awesome restoration as it were , work done and then some , some meaning polishing nuts, bolts, even wires and all in between . This video I watched restoration maybe at its best
I guess you forgot about the builder's plate or it was wrecked when you brushed it. Keep in mind builder's plate is also just as important as the aesthetics.
El rollo hay q remplazarlo por uno de hidrolavadora para q de 2500 RPM.porq este rollo solo da 1750RPM para q duren las piedras y ponere.conertores psra.evitar accidentes bro
Assistindo mais um vídeo seuChannel é deixar meu lik. Ah tem vídeo novo no Channel ok assista deixe seus comentários seu lik pra crescimento do mesmo vou ficar muito feliz com a sua visita e ative o sininho pra receber as minhas notificações dos próximos vídeos no Channel. Abraços VILMINHA fica com Deus.
Да, у человека явно дефицит инструмента, и отвращение к применению смазочных материалов. Ну бывает, делаем из говна конфеты подручными материалами, только провод питания внутри не зафиксировал - по крайней мере на камеру, хоть узелок бы сделал, чтоб не выдернулся.
If the threads of the old bolts are damaged it's better to use new ones to make sure it secures the parts very well. If u would reuse the old ones you would have to rethread the old bolts which means that you make new threads by taking away some metal. Because of that it's not always possible to make a tight fit. That's why he replaced the bolts.
14:18 Лупишь по подшипнику ! А слабо постель прогреть хотя бы горячей водой. Обмотка статора явно перемотана. Концы скручивает от неумения паять? Не заизолировал термоусадкой Колхоз на 3 с минусом
As an electrician I died a little when I see you just twist the cables together instead of making a proper connection using solder or a connector block. Connections that become loose cause fires.
