RV Water Damage Repair: Demo Day 10 Front Cap Repair

Подписаться 36 тыс.

Просмотров 31 тыс.

50% 1

Find the tools/supplies I use at www.amazon.com/shop/fallenint...
Book a consultation: www.fallenintocamping.com
Connect with me: linktr.ee/fallenintocamping
#rv #rvlife #rvrenovation #rvrepair #rvmaintenance #rvliving #rvtravel #rving #woodworking #woodworker #diy #howto #rvhacks #ac #acunit #rvaccessories #rvupgrades #heat #cooling
Disclaimer
Updated October 1, 2020
The information provided by Fallenintocamping LLC ("we," "us," or "our") on www.fallenintocamping.com or ( / @fallenintocamping (the "Site") is for general informational purposes only. All information on the Site is provided in good faith, however we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability, or completeness of any information on the Site. UNDER NO CIRCUMSTANCE SHALL WE HAVE ANY LIABILITY TO YOU FOR ANY LOSS OR DAMAGE OF ANY KIND INCURRED AS A RESULT OF THE USE OF THE SITE OR RELIANCE ON ANY INFORMATION PROVIDED ON THE SITE. YOUR USE OF THE SITE AND YOUR RELIANCE ON ANY INFORMATION ON THE SITE IS SOLELY AT YOUR OWN RISK.
EXTERNAL LINKS DISCLAIMER
The Site may contain (or you may be sent through the Site) links to other websites or content belonging to or originating from third parties or links to websites and features in banners or other advertising. Such external links are not investigated, monitored, or checked for accuracy, adequacy, validity, reliability, availability, or completeness by us. WE DO NOT WARRANT, ENDORSE, GUARANTEE, OR ASSUME RESPONSIBILITY FOR THE ACCURACY OR RELIABILITY OF ANY INFORMATION OFFERED BY THIRD-PARTY WEBSITES LINKED THROUGH THE SITE OR ANY WEBSITE OR FEATURE LINKED IN ANY BANNER OR OTHER ADVERTISING. WE WILL NOT BE A PARTY TO OR IN ANY WAY BE RESPONSIBLE FOR MONITORING ANY TRANSACTION BETWEEN YOU AND THIRD-PARTY PROVIDERS OF PRODUCTS OR SERVICES.
AFFILIATES DISCLAIMER
The Site may contain links to affiliate websites, and we receive an affiliate commission for any purchases made by you on the affiliate website using such links. Our affiliates include the following:
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn advertising fees by linking to Amazon.com and affiliated websites.

Хобби

Опубликовано:

7 июн 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 56

@johnderbabian6198 Год назад

Referring back to the last video, contact cement ONLY works if you coat both parts to be bonded and let them air dry first. I'm guessing the only portion that stuck was the piece that you used 'extra' cement on the other side at 16:11of the last video. Coat both sides and use a laminate roller to increase contact after placing the two pieces together. Awesome series of water damage repair.

@fallenintocamping Год назад

Yeah I kind of figured it didn’t stick because I didn’t clean the cap well enough too. Probably a multitude of reasons (and not coating both sides) but I’m not mad at it because epoxy works great too!

@DemetriaLara Год назад

beautiful work, I have not missed a single episode of your beautiful odyssey. keep going. 😅

@GN-mx9qx 2 месяца назад

Thank you for showing us the mess-ups, it is so helpful to know that messing up is normal!

@pinkladybikermamma3603 Год назад

GREAT TIPS. LEARNING A LOT. WE ARE GOING TO TACKLE A REBUILD ON A SCOTTY SERO TRAILER IN JULY.

@leeholt3475 Месяц назад

Love all your videos thank you for all the tips

@ridingtheasphaltrails.4114 5 месяцев назад

Thank you soooooo much for this video. My wife wants me to pull of the camper front and replace the rotted framing. This was very informative.

@aleckelsey402 Год назад

So wish I lived near you so you could do my roof. But thank you for the awesome videos. You keep on keeping on🙏

@joeandraska102 Год назад

Your videos are so well done and organized. Really appreciate the thoughtfulness involved behind the presentation. Also love the content. You could do a PHD class on making RU-vid videos. Your skills are amazing.

@NoWayJoseRV 9 месяцев назад

Use Stabond T-440 glue with a spray gun and only glue 2/3 from the bottom up and leave the top 1/3 unglued so it will bend easily. Trailer looking good !

@evansmith5387 5 месяцев назад

Agree Stabond 440 is the best option it’s meant for this purpose.

@stephengaryantes1420 3 месяца назад

Awesome job!

@TacTechTrail Год назад

Will try the freezer trick when I do my vent fan this month. Thanks!

@fallenintocamping Год назад

It’s life changing 😂

@jessealvarado6939 Год назад

Sorry you had to take it down after getting it up but great job on not giving up and getting it done looks perfect 😁🙏

@carolbigley1284 Год назад

Amazing !!!!!!!

@gsibertjr 4 часа назад

Contact cement would be a great adhesive for attaching the front cap to wood backing. You did not apply it correctly. Contact adhesive has to be applied to both the wood and back side of cap. A lot less expensive and will create a bond stronger than the woid.

@DrubieDoobieDoo 3 месяца назад

Impressive

@ryanteter Год назад

Relief cuts are everything. Nice work. Humble recommendation to use a high speed buffer with wool pad and Meguiar’s #67 to polish out the cap and sides. You won’t believe the difference.

@fallenintocamping Год назад

Will definitely try that!

@cirosochyesposito9443 5 месяцев назад

Thanks so much for sharing your excellent video! By the way what type of nails did you use?

@suzyfueshko9593 Год назад

I think the contact cement may have worked, but you have to coat both the front and under panels. Allow them to dry just enough that they are not sticky wet, then put them together. They should stick immediately.

@fallenintocamping Год назад

I agree with the both sides, probably should have tried that. But it also immediately dried when I rolled it on, like it soaked into the paneling. Second time was better, but I think the problem is it’s mdf and it soaks up everything 😕

@stephengaryantes1420 3 месяца назад

I wish I would have found this before I did my front cap on my class C cap. Cap has some issues when sun's out. Like it didn't cure good. When cool outside cap lays flat. Will have to pull it at sometime. So you used paneling and not luon flooring for the cap?

@mikeandre9027 Год назад

👍🏻👍🏻

@cwkhonda 2 месяца назад

Nice job. I'm curious how the liquid nails worked out? after it cured, was there visible lines from the outside where every stringer was? I know some adhesive will shrink as it cures pulling the material tight. which can show when fully cured.

@cindybundrick3469 Месяц назад

Great work! I need you to come help me! Ha!

@dutchgirl2 3 месяца назад

I used a magic eraser to clean the fiberglass

@michaelorourke9163 Год назад

I am rethinking the whole vinyl screw covers for my RV rebuild project. Here's my logic, I noticed that the quality control of the assembly from the factory leaves a lot to be desired. On my RV during disassembly, I noticed that several screws were put in at an angle which leaves a nice little path for water to start seeping in. Also I feel that those vinyl covers are acting as a dam to channel water across a longer section of the trim and screws. It certainly is not watertight, nor does it look like it is designed to keep water out. Especially since most of the pieces I removed were green and nasty looking on the inside. So my thought is instead of replacing the covers, what if I just fill the channels with a waterproof sealer and smooth them out with a putty knife. I'm really curious about what others think. I've seen others put a small bead of caulk along the vinyl inserts or use Eternabond tape over the trim and vinyl covers. But why not just fill the trim with say white silicon caulk and be done with it. Personally, I have used Eternabond tape over the termination trim pieces on both the front and back of my RV, and it was a major pain trying to remove to prep the roof for repairs.

@fallenintocamping Год назад

The trim cover isn’t meant to be waterproof. The corner or rails should be waterproof before applying the trim cover. You should have butyl tape underneath, and when the screw goes into it, it wraps itself into the butyl tape creating the seal at the screw. The trim cover is meant as an added protection in case the RV owner does not do regular maintenance (ie taking the corners off to replace butyl tape..for reference, my 5th wheel is a 2015 and I’m going to have to replace the butyl tape on my rails this year because it dries out). Wouldn’t suggest covering with anything other than trim cover, will make a huge mess and will be a pain when you have to take those screws back out. Water does not act as a channel if you seal it properly from the roof. Again, all about doing regular maintenance and sealing properly.

@michaelorourke9163 Год назад

@@fallenintocamping I can't remember where I saw/heard the comment on the covers being waterproof, but I agree with you (they are not). Yeah, I get the part of the butyl tape forming a seal under the trim piece when screwed in properly, but it looks like in way too many spots, they either drove the screw in too hard which dimpled the trim and probably forced the butyl tape away from the screw or drove the screw in at an angle causing it not to seal properly. Do the RV manufacturers have any quality control in their plants?!? I get what you mean about using putty over the screw heads because I did try that on the front and rear of my roof. However, I believe the water had already found a way around the area which I thought I had patched successfully. Until I checked closely this spring and realized it was still getting in and was a major PITA trying to clean up that mess. Hence the reason I am working on this project this summer. One could sum it up as "I am not a happy camper!"

@HomegrownHoneys-dd7it 3 месяца назад

What kind of wood do you use to glue the front to?

@challeis1 23 дня назад

Would a roller work better as an applicator?

@cecilhaire990 Месяц назад

Between 9:34 and 9:48 you make reference to a tape. Starts with “B” and I’ve never heard of it before. Could you elaborate a bit on what this is?

@fallenintocamping Месяц назад

Butyl tape? It’s basically a waterproof tape that goes behind any rails or under roof vents. It’s the first step of protection against water damage!

@suzyfueshko9593 Год назад

Just curious, did you apply any pressure to the front to hold it in place while the adhesive dries? I am planning on doing this with my camper.

@fallenintocamping Год назад

No I didn’t, the curvature of the front cap puts enough pressure on the adhesive to stick. It pretty much curves along every aluminum framing piece on that front cap

@rcrook9000 9 месяцев назад

If you ever feel like trying contact adhesive again, I use 3M 1357 for fiberglass to wood adhesion (not foam safe). It's quite a bit more expensive than others, but works really well. Once the two pieces go together, they will not come apart. A good and bad thing, lol... Do you usually recommend bonding the fiberglass to wood before putting it back on the camper? I've seen most people put the wood up first, then the fiberglass directly on the camper. So your method is really interesting and looks easier. However, I'm curious how would you do this with a larger sidewall where you can't screw in the panel to so many places?

@fallenintocamping 9 месяцев назад

I’ll definitely try that next time, thanks! I typically bond the fiberglass to the wood first because I really don’t like working in the air. It’s so much easier to just put the whole piece up rather than doing it separate, and making sure the epoxy lines up with the wood correctly. It’s 100% personal preference and you can do it either way, I just find it easier this way!

@sunnyazee905 Год назад

What type and size of backer board did you use? It looks like one piece and bigger than a 4 x 8.

@fallenintocamping Год назад

2 pieces and they were 1/8 inch paneling. Real wood is ideal but I can’t find that around my area

@jdubbs57 8 месяцев назад

my wife and i are about to undertake a similar project with our 2013 travel trailer. does anyone know the specific type of board and thickness that was glued to the front cap? at my local menards i saw 1/8 x 4 x 8 sheets of hardboard that might work. anything 1/4 or more seems too thick. appreciate any help. on a side note your videos are awesome. we were torn on how to proceed and your videos are so well done you gave us the confidence to try on our own. Keep up the great work!!

@fallenintocamping 8 месяцев назад

It’s 1/8. Can’t really be any thicker than that or else it won’t bend enough

@jamiewilson6702 10 месяцев назад

Hi! Just wondering where you got the square head screws? I'm currently in the middle of extendive repairs to my camper and can't find them anywhere!

@jamiewilson6702 10 месяцев назад

Also wondering what size Butyl tape you used?

@fallenintocamping 10 месяцев назад

Amazon! I’ve got them linked in my amazon storefront, but just search for RV square head screws and they’ll come up!

@tracyguitard7113 Месяц назад

Hi there, really love your videos , we are renovating a trailer and have the front off right now and we ordered the same west system adhesive that you used in the video and have a couple of questions 1. What did you use to spread the epoxy2. How big of a batch do you mix at a time and how many did you need to make and how long of a working time do you have before it sets up? And is there any suggestions for us as this is our first time attempting this and the epoxy is very expensive here in Canada and I’d hate to mess this up lol

@fallenintocamping Месяц назад

Hey! All great questions! I buy a couple cheap, large paint brushes to spread it. I usually do about 8-10 pumps to start (1-1 ratio), mix it really well, and pour it out onto the mdf and spread it. I’ve also used a mini foam roller to spread and it works well too, it just soaks up a little more of the epoxy and you would need a bunch of them (the epoxy makes the foam roller fall apart). I think it’s got a pretty long working time. You’ll be able to feel it getting hot in the cup if you’ve mixed too much and let it sit for too long. The only thing I would have done differently next time is apply the epoxy to both sides instead of just the mdf, but you’ll need 2 people for this (one working on each side).

@fallenintocamping Месяц назад

I also work in small batches, so it will take a few trips back and forth of mixing to get it all on the panel. It usually takes me about 20 minutes total from start to the time I join the fiberglass and mdf and start weighing it down

@seanbolza7649 Месяц назад

I'm tackling this project right now. Have mine off and all apart just waiting on filon to be delivered from recpro. Specifically what paneling is that? HD or Lowes stuff? Model#? Thank you

@fallenintocamping Месяц назад

Your friend has shared a link to a Home Depot product they think you would be interested in seeing. www.homedepot.com/p/32-sq-ft-MDF-Spartan-Oak-Wall-Paneling-48-in-x-96-in-x-0-118-in-00050/202765200

@seanbolza7649 Месяц назад

@@fallenintocamping does this stuff really hold up well? I've used this before on my laser printer just never imagined it good enough for a cap backer.