Samsung Slim Fit Wall Mount Unboxing Install on Neo QLED QN95A 55" 

Thankyou

@@TellyDan i can't wait for my samsung qled to arrive!

Thanks Andy

Thankyou for that, I know what you mean it took me a couple of goes before I did the video

Thankyou

Most welcome mate, took me a while on my first go

Thanks

I came to same conclusion. Instructions are complete garbage. Only useful once the job is done and the entire scope of what is taking place is already understood. At that point they are again best used to start a fire in the fireplace.

No you can only adjust the level

You can use a double arm bracket that has a 200 x 200 vesa mount

It shouldn't be a problem with a Samsung TV with the one connect system

If you recess the power outlets. The point of this slim mount is to be as flush to the wall as possible.

Did you fix it? Have the same question but i have Q80A...

Pre drilled then just normal wood screws

Did you ever find out the answer to this? Literally wondering the same thing

I think its mainly for cables behind it, if you have thick cables you need the 15mm gap so it doesn't push the tv away from the wall

Is there any reason to produce custom made spacers which push the TV 5 cm off the wall? The reason is to but back lights (Govee) behind the TV, and the light effect is better if there is a gap between the TV and the wall.

That's weird, glad the vid helped though

Off the top of my head I think the vesa is 400 x 300

Hi Ella, you need 2 of you to pull down hard on either corner of the TV until the bars click down into the brackets, then the tv will push back to the magnets

It's OK if it suits you. They are really hard to click down to the point where you almost think you're going to damage it. If you tilt it out and look from the side you should be able to see if it's clicked in or not

Think it's an m8, they come with the bracket

Yes, use the separate mounts that come with the soundbar

If you look closely at the brackets you can see if you need to straighten them up and see if the bar is fully down, then it should click back. I've had trouble with this myself and it does take a lot of force downwards

Is one of the brackets bracketst possibly?

Hi. I just decided to use a screwdriver to manually force a little bit the piece and open it up the space just a little bit, so the metal bar can go full down and do the click. I tried the normal way even after hanging the TV just putting the 2 pieces together and it was impossible to "click" them together even with full force so I did this method (forcing the piece and open it up a little bit before hanging) because i was really afraid to pushing my 75 inch TV with brute force. Maybe there is some kind of manufacturing error in some kits that make the space too tight or something. I hope this helps, but remember, dont force the piece too much, just a little so the bar go full down and you still need some pression to insert the bar to the bottom.

Hi Rob I think so, the only thing to watch for is how high up the top vesa holes are so the brackets won't be visible above the tv

😄

This tv comes with a main hub (like a tv box set) where all the cables, power, HDMI, Ethernet etc plug into. There’s just one single cable that plugs into the tv that transmits everything too it including power.

Have you tried samsung.com the frame bracket is slightly different to this

No problem

Glad it helped

Update: the slim mount is working great with the 85 inch QLED.

Please @TellyDan, really waiting for your reply. Also I watched your Q80A unboxing video and I bought that tv.

I tried fix Q80A tv with WMN-A50EB/XC Slim Fit Wall Mount, and bolts which you put to tv are to short (in box you have 3 different size bolts - all are to short) now only i need to find and buy right size bolts - 0,4 cm longer or 0,4cm + 0,7 cm (with distance to 15mm from the wall)

screw 8x30 fix it

It possibly would, you may have to use different bolts bit I think the only thing that would make it unusable on other tvs would be if the vesa mounts are too high

@@TellyDan thank you!

It is compatible I think. I'll double check

I'll see what I can do

@@TellyDan ok sir..

Yep, pretty sure

You have to pull the 2 bars fully down into the brackets then it will push back and click

@@TellyDan Now I got it! Thank you very much.

@@saulinhobahia you're most welcome, it is hard to pull it down

Didn’t get the clicks either! Will try again when I put the TV back up after house renovation is finished!

To be honest you may as well go for a standard bracket to accommodate the plug thickness

Yes you need to shine a torch and check the bars are clipped into the brackets. They're quite hard to get in first time it takes some pressure, then when you push the tv back it should click to the magnets. Also check the bars have gone straight after clicking I down

@@TellyDan I thank you for your reply, done and the click to the magnets is okay

@tellydan no matter what I do it won’t click and it’s in an incline

@@69incher Hi, please see above

Thanks Mark if I ever move to Wales you can put my aerial up for me

Yes you can

Thank you really much!

Hi gecko the 2 different setting are to accommodate different amounts of cables behind it

It's the same slim fit wall mount for all of them apart from the q80a

@@TellyDan Thanks for replay pls one more question if you must pick: Lg nanocell 70" or 75" serial 753pa 140 euros difirents.

Hi mate. Just had this installed and the little silver bars on each mount won’t slide right into the bottom grove of the wall plates. Tried to force it down but just hoovers over the 1st groove. Are you saying it’s need to be lifted out the groove and raised out so that it actually clicks into place ?

@@waseemmansha i don't quite understand your wording. I suggest hanging the wall brackets first and then before connecting the other parts to the TV, just see how they fit by hand. When you do you see how easy it is. They hook over and down and then lift up for the magnetic lock

Sorry hard to explain. On the wall mount, if you look closely, there’s 2 little indents. When you slip the hooks into the slot of the wall mount it sits in the first groove but there’s a tiny gap under it which I assume is where it can do down a further level so that the magnetic can then rest against that little black tab which goes vertically down. I know you can insert the hooks and then raise it slightly for magnets to kick in but if you then tilt the TV forward, there’s a risk that it will just come off the wall completely. Just trying to see how the hooks go in correctly so the magnetic kicks.

it's impossible for me to comment since our TV is now mounted and I can't see it.

@@waseemmansha you need to force the bars past the notch so it clicks. You can see in the instructions it says you must do this as well. It takes quite a lot of force. I used a quick sharp pull down from the top on both sides and you hear a click. Once this happens you can then push the TV back towards the mounts and you will hear the magnets engage

You can use a normal bracket as well

@@TellyDan is it possible if you can uploud a video using a normal bracket please

@@zxcbnm7829 yes I should get around to it at some point

Yes it does

see my post

It's possible as long as the mounts don't show behind the tv, it depends how central the vesa mounts are to the tv

No but it gives you the relevant dimensions to mark up for the brackets

The only thing that could be a problem if the vesa holes are high up the bracket could be visible

@@TellyDan Okay cool. Because I have a 2020 QE55Q90T and from what I can tell it would be fine, but wondered why Samsung do not mention older models in their compatibility list.

@@brucejohnson5208 probably to sell you a new one lol

@@TellyDan Haha, genius! But not going to work.

@@brucejohnson5208 haha good man

Yes it is

I was wondering the same. I just bought a 55" QN90A and bought this wall mount separately, read the tv's its comparable with and it doesn't list the QN90A. Wondering if the QN95A is the same mounting instructions as the QN90A?

@@dennyni From what I know the only difference is that the qn95A has the One Connect Box and the other one doesn't. So the compatibility should be identical.

Yes, it will

Yes it is

@@TellyDan which screws do you recommend for plaster board

@@rajaraza4037 I use the spiral shaped metal drywall anchors, they seem pretty solid

@@rajaraza4037 laffeya Wall Anchors and Screws for Drywall, Zinc Self Drilling Drywall Anchors with Screws Set- 10 Screws, 10 Self Drilling Zinc Drywall Anchors Use for Screws Professional and Home Use (20PCS Short) smile.amazon.co.uk/dp/B08L8XNGC6/ref=cm_sw_r_apan_gl_i_P8A2DQADKRG31WMW7T8M

Thank you man

Yes I would, makes a tv look nice and neat. Tight to the wall and minimalistic