Saw Stop Router Assembly

Подписаться 74

Просмотров 24 тыс.

50% 1

This is the assembly of the Saw Stop inline router table. This video is not sponsored in any way. I am mounting the router table on my 36" Saw Stop PCS. You will also see me install the Saw Stops router lift, dust collection box, and the intermediate cast iron wing. I'm installing the router table on the right side of my table saw so I needed the intermediate wing to fill the gap but for left-side installation, you should not need the wing at all. Installing the router table on the right also keeps the footprint of the table saw the same so if you are short on space like I am the right side install might be your best bet.
I purchased the cast iron table, legs, fence, and power switch together in a kit which is Saw Stop Part # RT-TGP. I also purchased the Intermediate Wing Saw Stop Part # IT-ICW, Router Lift Saw Stop Part # RT-LFT, and the Dust Collection Box Saw Stop Part # RT-DCB.
If you want to see the unboxing of all the parts I used please check out my unboxing video. • Saw Stop Router Table ...
Chapters:
0:00 Intro
0:26 Disassembly
2:52 Intermediate Cast Iron Wing
7:25 Router Table and Support Legs
11:44 Fence Rail Reinstall
12:35 Router Table Fence Assembly
12:50 Router Lift
16:54 Dust Collection Box Assembly
17:22 Dust Collection Box Install
18:45 Router Table Fence Install

Опубликовано:

3 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 28

@tab01560 2 месяца назад

Excellent video. You should do more showing your projects.

@Marcus_Caius 2 года назад

To install the extension, clamp a 2"x4" on each side and under your existing cast iron table. Have the 2"x4" extend your PCS table and it will hold the extension, making that whole process a breeze.

@davidcahoon7666 2 года назад

Thank you so much. Putting mine together this afternoon and this has been so helpful.

@elmswickandoak 2 года назад

Hope it went smoothly!

@KHDailyKnives 7 месяцев назад

Thank you for showing your build! I have the same 36” saw and am strongly considering doing this. I just wish all the wings and such were not so expensive. It sure seems like I won’t regret it when I go ahead and do it.

@stevedunn17 Год назад

Nice. one small complaint- the sound of your music is about 5 times louder that the voice part which forces one to keep adjusting the volume. HAve a nice day.

@kevinb6102 Год назад

Great video

@kinder-works Год назад

I just figured out that the knob used to raise and lower the lift is an 8mm wrench. It should fit the router clamp.

@kevinb6102 2 года назад

Wow now that’s a saw

@atomictyler Год назад

just need to stack up your systainers to hold the extension while you're bolting it up.

@jhewitt17 10 месяцев назад

Are you able to tell me the on-center distance between the router fence track slots. Sawstop says that they don’t have that information. Odd. I’d like to use a different fence. Thanks.

@generalsworkshop 2 месяца назад

Great job. I’m looking at doing this also… now that you had it for a couple years, do you still like adding it into your table saw or do you wish that you would’ve done it and a separate structure from your table saw?

@tinaalexander6307 Год назад

I found the best product to protect against rust is called, " Carbon Method.

@baba_babaa2 Год назад

can I just remove the cast iron wing and just attach the table to my center main cast iron table? I want to make the saw much smaller I don't need or want it that large

@Conradlovesjoy Год назад

You still have to deal with the fence rails…. So the saw doesn’t get any less wide doing that.

@kevinb6102 Год назад

Installing the router table top doesn’t make the table saw any wider does it?

@Conradlovesjoy Год назад

No. If you look when it’s installed, it’s no wider than the original fence rails.

@sloppydoggy9257 9 месяцев назад

Does the router plate actually screw down into the router table top? It looks like maybe its the two larger counter sunk holes in the left/right of the middle?

@sfdclay Год назад

Was it worth it? Seems like it reduces your table saw capacity by quite a bit. Is it the best router table solution in the market?

@elmswickandoak Год назад

Hey Clayton, It doesn't impact the saw capacity at all. You do have to remove the router table fence but with the cast extension insert and the router table itself, it fits within the exact same footprint and overall table size. I don't know that it's the best router table solution on the market but I was looking for something that would not add take up space in my shop. It works really well and don't really have any complaints that are worth mentioning.

@theworldturns Год назад

Hi, for the CNS, Sawstop say it's not compatible with the mobile base. I don't plan to move the saw very much but would like to keep the mobile base installed. Is this going to be a problem? thanks.

@elmswickandoak Год назад

I have the industrial mobile base installed and have not had an issue.

@tchornomud 2 года назад

hey, so in theory, the process would be the same, if you wanted to install on the left?

@elmswickandoak 2 года назад

More or less but you wouldn't have the extra cast iron insert.

@manafalbazaz5892 2 года назад

What router did you used ? Is it one router brand can fit there or any router?

@elmswickandoak 2 года назад

I put in a Bosch 1617evs. It should fit most router brands; the bosch, Porter Cable 7518, and Milwaukee 5625 are the most commonly used. However, Porter has had quality issues over the past few years.