Тёмный

Scorpion Tribunus 120 ESC-Basic setup video 

poomi
Подписаться 635
Просмотров 12 тыс.
50% 1

Опубликовано:

 

30 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 27   
@epoweredrc
@epoweredrc 3 года назад
Thanks for this video, I am about to get my first scorpion esc ever so i needed to learn how to program everything.. I plan to use the usb cord and not the adaptor cause getting it used with a heli and i'm sure he doesn't have the adapter.
@PoomUdi
@PoomUdi 3 года назад
Usb chord is fine!!
@aussiedigger1441
@aussiedigger1441 2 года назад
On my Tribunus2 120 I can't change the drive frequency and timing?. The motor & caps on esc are to hot to touch after 1min on the ground with no blades?? Also motor makes a high pitch noise around mid stick. Spent nearly a $1000 on scorpion products for my G570 and I can't even use it without cooking everything.
@very9000
@very9000 3 года назад
Look, I first set up the ESC SCORPION through the application (limited) in V-Bar Control, now I am setting up through the computer in the SPROTO application. Will there be no crash with synchronous settings? What do you think ? 🤔
@very9000
@very9000 3 месяца назад
HELLO. PLEASE TELL ME WHAT SETTINGS YOU HAVE SET TO SORT THE ROTOR TO SPIN SO SLOWLY?
@very9000
@very9000 3 года назад
Hi. I am using GOVERNOR ESC SCORPION. Is it possible that on the ground there are some rotor revolutions, and others in the air? (They are respectively lower)
@PoomUdi
@PoomUdi 3 года назад
Lower rpm in the air? Due to your rotor disc being loaded up, normal.
@very9000
@very9000 3 года назад
@@PoomUdi thanks 🙏
@very9000
@very9000 4 года назад
Hello. I purchased a Tribunus 14-300A Series engine governor. I cannot pair with V-Bar Neo (V-Bar Control). I also want to connect via telemetry wire ... I still do not understand which socket in the figure is "MASTER", which is "AUXILIARY" ??? There are 9 pieces of pin connections .. Help me please🙏🙏🙏
@PoomUdi
@PoomUdi 3 года назад
Master is for your throttle signal from the Rx and Auxilary is for rpm sensor.
@very9000
@very9000 3 года назад
After loading from a file, my Sproto program hung and now I do not see ESC SCORPION. Help if you know?
@PoomUdi
@PoomUdi 3 года назад
Make sure yoy have proper drivers installed
@very9000
@very9000 3 года назад
Hi. What kind of governor do you use? ESC scorpion or vbar governor?
@PoomUdi
@PoomUdi 3 года назад
I use Scorpion internal govener eventhough I fly on the Vbar. Just my personal preference.
@very9000
@very9000 3 года назад
@@PoomUdi Thanks. Help me ... I have 80% gas shelf. When I took off for the first time, the helicopter did not rise for a long time, and only when the throttle stick was in the extreme upper position, the helicopter took off. When I raised the helicopter again, everything was fine, the throttle stick was just above the middle. Although I did not change the gas shelf, I left 80%. Do you think this ESC is configurable?
@PoomUdi
@PoomUdi 3 года назад
@@very9000 Try a recalibration
@very9000
@very9000 3 года назад
@@PoomUdi Please tell me, when changing the GAIN parameters (soft, middle and hard), how is the helicopter controlled? What does this affect? How does it feel when flying a helicopter? Yes, I want to say that now I am adjusting the flight ✈️ of the LOGO 800 helicopter, like the flight of a copy helicopter, I do not fly 3D. Looking forward to your reply, thank you 🙏 in advance.
@very9000
@very9000 3 года назад
@@PoomUdi Thanks. If all is well now, do I need to re-calibrate or not?
@thomaslang7634
@thomaslang7634 4 года назад
Could you please explain how to calculate the value for "max battery power"?
@PoomUdi
@PoomUdi 3 года назад
If you use a 5000mAh pack, and let's say you want to have 20% left in the pack. This would give you 4000mAh of usable capacity. Take 4000mAh ÷ 1000 to get the value in Ah. Which would equal to 4.0Ah
@bugoXngAZ
@bugoXngAZ 7 лет назад
Neo vbar control, goes to vbar pid or external gov if i want to use vbar governor? Thanks
@PoomUdi
@PoomUdi 7 лет назад
Select Vbar PID for Vbar use, you can check out the scorpion website on how to DIY a telemetry cable as well.
@bugoXngAZ
@bugoXngAZ 7 лет назад
poomysan got it got mine working now, but i notice when i hit my motor idle it does something really different,
@TheRagge1
@TheRagge1 7 лет назад
on the trottle curve , normal why not a straight 65 % curve and use trottle hold for 0
@PoomUdi
@PoomUdi 7 лет назад
TheRagge1 , in case I forget and flick hold off when the heli is in an unsafe position... just a habit for me.
@johnahamelv
@johnahamelv 5 лет назад
@@PoomUdi Just don't forget to switch out of that flight mode before going inverted.
Далее
Kyle Dahl Tribunus setup VControl
12:45
Просмотров 16 тыс.
HobbyWIng 160HV overview
7:59
Просмотров 10 тыс.
JUJU HAS IT ALL! | Brawl Stars Animation
00:53
Просмотров 4 млн
soXos Strike 7.1 - Überblick und Aufbau
19:47
Просмотров 3,9 тыс.
VControl Touch Basic Setup Video With Tips!!
23:41
Просмотров 15 тыс.
DX9 VBAR NEO SETUP (Full Capability)
17:08
Просмотров 7 тыс.