Service U-joints in minutes using the Tiger Tool 10105 U Joint Puller & 10202 Bearing Cup Installer

Просмотров 658 тыс.

% 2 135

Available on Amazon
20503 Kit: a.co/d/cYSWJRq
10105 Puller: a.co/d/9DD3IYz
10202 Installer : a.co/d/45eo1YA
70300 Pliers: a.co/d/0Zx7TOP
Product Details: www.tigertool.com/tools/?classification=automotive
Tiger Tool 10105 - U Joint Puller
U-Joint Puller designed to fit cars, light-duty trucks, and farm machinery. Fits u-joints with bearing cups 1.0" to 1.25" O.D"
- Eliminates dangerous vice and socket, or hammering methods.
- Removes sealed u-joint cups in minutes.
- Does not damage the driveshaft, yokes, joints, or bearing cups.
- Patented design provides the most effective mechanical advantage for disassembly.
- Heavy-duty construction.
- One piece unit (no assembly required). No bolts, no cables, and no adapters.
Tiger Tool 10202 Bearing Cup Installer:
The Tiger Bearing Cup Installer installs two bearing cups in one procedure. An encased magnet retains bearing cup #2 in place over the yoke assembly opposite the forcing bolt. Meanwhile, bearing cup #1 is maintained in place by the force of the rotating plunger at the end of the threaded bolt.
Both bearing cups are pressed simultaneously, freeing the mechanics hands to both; operate an air-wrench, and; maintain the position of the u-joint cross during the installation procedure.
Fits virtually all medium and light-duty universal joints.

Авто/Мото

Опубликовано:

25 май 2011

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 193

@HowToolVideos Год назад

Available on Amazon 20503 Kit: a.co/d/cYSWJRq 10105 Puller: a.co/d/9DD3IYz 10202 Installer : a.co/d/45eo1YA 70300 Pliers: a.co/d/0Zx7TOP

@user-hp3ei1os9d Месяц назад

I just bought one it works great I’ll never use the old socket and hammer method again 👍

@lauratwo16 12 лет назад

By design, force is applied ONLY to ONE cup, NOT TWO as with a typical ball joint press (c-frame). Tiger uses approx.HALF the force a BJP would take to do the same U joint. For those seized-up stinkers it appliest approx.TWICE as much force as the BJP at a given scrw pressure. If it looked too easy it's because it was TWICE as easy using TIGER TOOL. I took time to say this because they are GREAT to deal with... I got AWESOME customer sevice recently thamks to KEVIN. I don't forget that. JP-USA

@billrau2398 2 года назад

Outstanding !👍🏽 video I never knew this tool existed till now I just ordered one can’t wait to start using it 👌🏽

@MrMechanicMike 10 лет назад

what a neat setup.

@donnaedminster1463 8 лет назад

I installed the u-joint with this tool and I used my solid gold 3/4 ratchet

@Nostradamus_Order33 5 лет назад

Donna Edminster 😂🤣

@johnb1121 3 года назад

😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂

@Macsmoney 2 года назад

You clearly were trying too hard!! He only used a silver 3/8 ratchet. By the way…….he did it in 6 minutes, how long did your big hammer take? Time is money in a shop, and having done hundreds of u-joints I would buy this tool again if mine broke

@BillyDocWalker 5 лет назад

Auto Zone will lend you these tools

@phendrix9476 3 года назад

Bought the 10105 a while back. Used it today to press out my ‘01 Dodge 2500 front axle u-joints. This thing made it extremely easy! Used a 1/2’ Cordless impact. Just used my balljoint press to reinstall. Well worth the money imho.

@2vcrew782 2 года назад

Snap On BJP1 BJ press ?

@ohell226 3 года назад

I like tools. 9 years later RU-vid pops up in feed. Not enough rust on that to be impressive. Plus cost for DIY. Already own two sockets and BFH.

@terrellscaife2411 2 года назад

Amazon and eBay how the knockoffs for $50 or less

@zacharymontizor8871 11 лет назад

Awesome tool!!! Thanks for the share!

@elmergamez 12 лет назад

Nice!! Easy with the right tools I must get one of those tiger tool

@Rick-bt6je 5 месяцев назад

Thanks for the great video tutorial, very much appreciated

@dolphinsc1 11 лет назад

excellent video! I have never seen that removal tool. Nice, Clean and quit! great vid.

@derekhellam9861 7 лет назад

I have the puller except fit heavy truck drivelines love it

@toddbernal4143 6 лет назад

On sale on amazon only 99 bucks for the removal tool! A must for any flat rate mechanic.

@timparker3272 4 года назад

Very useful tool! Made it look very easy bc it was!!

@zappatx 2 года назад

This would be great for on the road rescue operations. My only issue was the drummer for the background music. So all in all good review.

@AK99581 Год назад

Yeah that background music is pretty goofy lmao..."dun dun dun dun!!"

@scott3816 9 лет назад

awesome tool

@Mr1968gtx 11 лет назад

At 3:29 all I was doing was pushing the bearing caps in tight enough so they wouldn't fall out while I got the C-frame in to place. The cross of the u-joint slid in freely. I have however done what you suggested years ago on my Jeep... I had to change the joints out 3 weeks later!

@dc5723 3 года назад

I wished my Toyota u joints bearing caps came out this easy. Not only I used the Tiger Tool to push out the caps, I had to pound them out with a brass punch and 2 lb sledge hammer.

@peten6445 4 года назад

Great video.

@youandiryan 5 лет назад

I have one of these. If the u-joints are very rusted you will have to use a combination of hammer and socket technique, and this tool. This tool does not push universal joints out well when they are very rusted.

@terrellscaife2411 2 года назад

It sounds like you’re not using the tool properly because I went and got an old rusty driveshaft from the junkyard and I was able to press the caps out

@colinkennedy908 2 месяца назад

Just did mine rusty crap on 88 cherokee. Pb blaster and ratchet. Not too shabby at all.

@youandiryan 2 месяца назад

@@colinkennedy908 yeah I could have been doing something incorrectly haha honestly I don't remember now that was like 5 years ago. Those new joints that I have installed on the day that I left my original comment 5 years ago are still good to this very day!!

@1AAuto 12 лет назад

Great U-Joint video.

@jbr496 10 лет назад

I want one of those!

@khimsophacarfixing 2 года назад

These two tools are easy to remove and install!

@LUckybones25 12 лет назад

I've gotta get me one of those!

@howardgriffith71 3 года назад

I need mine done you made that s*** look easy

@jjenson2006 12 лет назад

A socket and a vice always worked for me.

@WeTrudgeOn 9 лет назад

Don't worry, harbor freight will no doubt have a clone pretty soon for 40 bux for the pair, those could be produced somewhere in Asia for five bux each.

@hddm3 9 лет назад

wish they would hurry up

@hddm3 9 лет назад

hddm3 don't know why these places want to price there selves out of the market. pro or not, that's just to much money

@Satchmoeddie 8 лет назад

Especially with that cast crystallized recycled monkey metal they use. I thought, "WOW< these Harbor Freight deep clamps are awesome for $12. They are okay to repair a guitar, but anything where you need some force the frame breaks apart rather violently.

@SnakeRiverFishing 10 лет назад

Nice, gotta stick to my hammer and drift method over here though $$$

@smotleyjr79 10 лет назад

only issue with this is the damn PRICE! If they sold them for $50 then more people would use it and buy it....

@oby-1607 4 года назад

I picked up a set at a yard sale for $5. Works awesome, the woman who sold it didn't know what it was.

@markkulyas2418 4 года назад

If it was $50.00 it would be a piece of junk that would bend or break.

@eprn1n2 3 года назад

If they gave it away demand would go through the roof!

@tnsd5801 3 года назад

Was your car cheap? If you can't afford to maintain your vehicle. Might I suggest public transportation or a bicycle or old fashioned walking. Proper tools that are of sufficient quality to repair vehicles without breaking are as you put it "is the damn PRICE!". You must think the people who work on cars should do it for free. I mean it's so easy a quadriplegic mud puddle can do it. You have no skills because you have no idea that tools of any craft cost money. You are the burger flipper demanding $15/hr and being replaced by a self order kiosk.

@Justo506 12 лет назад

thank you sir this was a huge help

@speelksurche 7 лет назад

very good

@blass5506 3 года назад

I use a c clamp an a socket easy removal and installation I’m not a mechanic but handy

@No-vm7go 6 лет назад

Great looking tool, but I just used one of those big u-joint presses and broke a cap. I went back to using a socket and hammer.

@Nico-iv1cq 3 года назад

Good tool.🙂

@phatymaniac 11 лет назад

awsome!

@dalestewart7733 12 лет назад

the u joints I just removed required a 4 ton press...came out with a bang each time. I think I'd have broken a tool like this trying! one time the joint broke through the bearing cap cause it was stuck so badly! If I thought this tool would work on rusty 15 year old salt soaked rusty trucks, I'd buy one today!

@orange3203 2 месяца назад

It can likely impart far more than 4 tons of force.

@Anubis78250 12 лет назад

Now lets see you do that on real world u-joints ... you know the ones that have been installed for 20 years. Those came out way to easy, and it didn't look like it was because of the tool. Seriously though, why not just use a ball-joint puller.

@jimsperlakis5634 2 года назад

Yeah, and how about ruining the Aluminum style yoke while he's at it with the single end tool !!!

@kentellis9071 7 лет назад

Handle it! 👍

@TheSauce05 12 лет назад

Just did the u-joints on my 2000 F-150 and there's NO WAY this tool would have worked to remove the old ones. Since I didn't have a vice it took me and a friend to hold down the driveshaft and use the ball-joint/u-joint press to press the joints out and the new ones in.

@teflondonhks50caliberbarre72 8 лет назад

$300 are you fucking kidding me sockets & Hammer that's the best...

@Satchmoeddie 8 лет назад

That was my reaction. F__K THAT! It should be hydraulic for that kinda coin.

@brutalblues 6 лет назад

The music...

@tomjoad1363 6 лет назад

When you use the C-clamp to put the little retainer back in place, how does only one side is pushed inside, and not both since both jaws of the clamp are sitting on the U-joint outsides?

@lauratwo16 12 лет назад

A big vice can become a boat anchor due to overloading. The typical Acme thread pitch is not capable of properly (w/out cheater pipe) creating the force required for many stubborn cases. Some huge vices have relatively WEAK captive nuts. Vice method w/sockets (like ball-joint press method) is trying to move both cups instead of 1 cup the Tiger Tool way. So again the Tiger requires approx. half the force the vice needs to do the same u-joint. Tiger goes under vehicle too-saves time . JP-USA

@dfjohnson76 8 лет назад

this thing is $385.00! I don't know who buys this thing. if you have a shop and are trying to run a business you can't spend $400 for this thing. the savings in time vs. doing it the old way will not off set the cost. profit margins are too tight for extravagances like this. BUT I WOULD LOVE TO HAVE ONE!

@SidewaysGts 11 лет назад

Seems like a great tool for a shop where you miiiiight encounter that 1 in however many cars where a hammer/socket wont work.. buuut for the rest of us? Ill stick to a hammer/socket. Awesome idea though, just with the price was a bit easier on the wallet.

@lauratwo16 12 лет назад

4 tons / 2 = 2 tons on the Tiger Tool.....My Tiger Tool has handled that kind of force no problem. JP-USA

@iwillnotcomply7145 2 года назад

U-joints in Minnesota do not just come apart lake that. LOL

@85jmccoy 6 лет назад

Its only 99 on amazon now,if you have ever been the ears of a drive shaft u can appreciate this tools value.... Dont ask me how i know,plus it speeds the whole process up pays for itself after 2 or three u joint jobs

@wormius428 5 лет назад

My 95 f250 has an internal c clip for the front passenger joint so this tool will save me hours of work since you cant fit a press there. Very excited to get this

@triiko 10 лет назад

Would be great if you did a lot of u-joints or if money is no object.

@Doomzdayxx 9 лет назад

This would totally be worth it if it cost like 20 bucks

@johnnysix7162 9 лет назад

No kidding... they want hundreds for an overglorified C-Clamp.. you can buy a damn press cheaper!!

@abel442 10 лет назад

A BALL JOINT REMOVAL TOOL WORKS ON REMOVAL AND INSTALLATION I OWN ONE ,IF YOU DONT OWN ONE AUTOZONE RENTALS ARE FREE JUST LEAVE A DEPOSIT, BTW CLEAN AND LUBRICATE ALL MATING SURFACES TO MAKE THE JOB EASIER.

@28704joe 4 года назад

Bearing cup mating surfaces go together dry, not lubricated.

@leehotspur9679 2 года назад

@@28704joe No, Anti seize or rescue steel used sparingly stop corrosion and dry face shearing

@28704joe 2 года назад

@@leehotspur9679 Howard, look this issue up on the Spicer website. Cheers. "Caution - Spicer DOES NOT recommend wiping the outside of bearing cup assemblies or yoke cross holes with grease, oil or silicone-based sprays. This could result in bearing cup assembly rotation in yokes. "

@eastcoastjay1983 6 лет назад

I like how he stops installing the second cup because he probably jammed the bearings lol. you can see the cup sticking out when installing the yoke. too expensive! ball joint press and a hammer is the way to go

@tevsil1 8 лет назад

you realize the "installer" c clamp does the exact same thing with a little more positioning right?

@billjabsjabbing9120 6 лет назад

so C clamp and a big socket would be about the same thing?

@delta614 4 года назад

basically

@all4runner316 4 года назад

I just tried c-clamp, it couldnt handle the job. Ball joint tool works well.

@Nostradamus_Order33 5 лет назад

Why not use a two jaw gear puller?

@supermoistdeluxe 2 года назад

You don't need a c clamp to press them back in. Take a second to clean the cap hole out and debur the edge. They slide back in

@astrogypsy 4 года назад

Sweet, but it's the bench vice and sockets for me.

@TigerTool 13 лет назад

@TsmnnDvl5 Hi TsmnndvI5, We have manufactured these tools for over 20 years and have yet to here of a case where this has happened. Generally speaking the yoke ears are stronger than the cast portion of the glove that pulls against the yoke.

@TigerTool 12 лет назад

We have been manufacturing this tool for over 25 years and I can only recall a few instances (we have been made aware of) where the driveline was so seized our tool wouldn’t work. In most cases we find it’s more important how the force is applied verses how much force is applied to complete this type of job correctly.

@Sm-ne8ff Год назад

G R O O V Y !!!

@inlinesicks 10 лет назад

So much more civilized than the old hammer and socket lol.

@robertcowan8211 5 лет назад

LUBE THREADS ON PULLER, REMOVE GREASE ZERK FIRST

@ceemihail 10 лет назад

Awesome tool, and good video. I'm going to replace the U Joint on the rear Driveshaft of my pathfinder, because I'm getting some vibration between 40-60mph and squeaks when I drive, and it's worn out . Would it be wise to replace the front also? Even if it's not worn? Thanks for your advice.

@consaka1 9 лет назад

If money is an issue AND the rear is a premature failure than just replace the bad one. If both have a lot of miles on them its just a good idea to replace both. Unless you are under your rig quite a bit I recommend using spicer maintenance free joints. They have superior seals and last a very very long time.

@PeaceBong 5 лет назад

I like it but I find the use of 2 separate tools to be excessive. Both removal and replacement can be achieved by using a balljoint press which is similar to the install tool shown. Great demonstration though.

@TheRealCharlieSuper 3 года назад

Cool, I'll just stick with my ball joint tool kit...

@brucearner Год назад

What if you have joints with clips on out side ?? Nothing in video on that !!

@alexhaywood9706 8 лет назад

If the driveshaft is bigger than that tool it won't work, a ball joint tool is just as good and does another job too. Replace ball joints as well. Great marketing

@louisernesto5886 2 года назад

You all prolly dont care at all but does any of you know a way to log back into an Instagram account..? I was stupid forgot the password. I would love any assistance you can give me

@jamietitus6220 2 года назад

@Louis Ernesto Instablaster ;)

@louisernesto5886 2 года назад

@Jamie Titus Thanks so much for your reply. I found the site on google and I'm trying it out atm. Looks like it's gonna take a while so I will get back to you later when my account password hopefully is recovered.

@louisernesto5886 2 года назад

@Jamie Titus it did the trick and I finally got access to my account again. Im so happy! Thank you so much you really help me out!

@jamietitus6220 2 года назад

@Louis Ernesto happy to help xD

@sschapasc 11 лет назад

Needle bearing jump out on ya? Cool tool, but I'll stick with my 20 ton press.

@sarmientosarmiento2338 3 года назад

Amigo te hablan de aquí de Colombia Qué precio tiene esa herramienta para cambiar crucetas Gracias amigo

@AWD_T 10 лет назад

Very nice. Beats a hammer and a socket. How much for the puller?

@brucemadden1626 4 года назад

can't tell you the number of times doing it this way has caused one of the needle bearings to "fall down" and get "squished" during the press-in. (and yes, the bearings were greased before hand just to keep them from "falling down"). Found it much safer to push one cup well past the circlip hold to be si\ure the opposing cup with its needle bearings would NOT fall down.

@billw4646 2 года назад

Looked to me like that might be what happened in this video. The second cup looked like it never fully seated and never showed putting that clip in on video, and at the end you could see that cup sitting a little too proud of the ear on the yoke.

@charliedee9276 2 года назад

Or just make sure the trunnion is inserted in both cups before pressing them home, just float it between the two while pressing.

@anthonypeterson5618 8 лет назад

Nice but putting that cup on should b one side at a time or risk hitting the pin bearings in cup then.....u kno what happen then.

@brianxr4160 8 лет назад

It's $176 on Amazon on 12/13/2015. I'm going to trade the 6 year old whiny one sitting across the table from me for one of these tools.

@ricgomez1 7 лет назад

BrianXR Every one has a whiny kid, there isn't a big demand for one of those.

@doghouse96zj92 5 лет назад

i made the same tool along time ago out of a pitman are puller and a large c clamp and a socket. a bit over kill on the price

@regorekrub 11 лет назад

What happened to the one that didn't want to go down..?

@sd90mac61 4 года назад

He had to remove it and reline the bearings, that does happen sometimes.

@RichieRich845 Год назад

Can you use the first tool to also install?

@robbieharris9339 3 года назад

I have NEVER had a u-joint come out that easy OR go in that easy also. They have always been rusted in.

@spawnsrevenge 11 лет назад

@ 3;29 it is possible that he didn't make sure the u-joint was inserted far enough into the cap and a needle bearing may have fallen out of place. That will not allow the cap to go into it's proper position and could destroy the u-joint if not done properly. May be why it appeared to be hung up.

@piglett2195 12 лет назад

looks good , probably better than my BFH & big block of wood that i use : )

@travisaudioelectronics12vo90 Год назад

I purchased th 10105 and it does not work on Chevrolet 1500 alumium shaft , it slips off.

@AZDESERT2024 5 лет назад

$100 for a C clamp . Available at Home Depot for $10

@GorillaFPV4life 5 лет назад

Those tools would have been really nice to have... a hammer and sockets worked really well though lol. He didn't even finish lol

@Bmartinezx3 12 лет назад

does any store carry this u joint puller as a loaner?? need one by tomorow

@Ham68229 13 лет назад

What are the chances/odds of this tool bending the "eyes" where the caps go while pressing in or out? A very interesting tool kit.

@billw4646 2 года назад

This type tool eliminates the risk of spreading the ears on a yoke because instead of pushing them apart like we used to pounding them out with a BFH or using a ball joint press you instead are only pushing on the sides of the opposing yoke's ears (or the u-joint trunnion after you have one side out) where there is no risk of spreading them and pulling on just one ear while pushing the trunnion. There is no risk of spreading the ears on the yoke when there are no forces applied in opposite directions to both ears like the old-school methods would often do, especially if one cup was seized up like when a seal got stuck or someone forgot to remove a clip or someone used an impact on a press and hit it with too many uggaduggas. This type tool is an improvement over the factory recommended press adapters that push on the trunnion as it works on the same principle in that it only is applying force to one ear instead of both but this type adapter fits a wider range sizes of u joints. FWIW now that I suppose the patent ran out or whatnot there are other companies now making their own versions of this tool, like OTC and Lisle. FWIW the Lisle has held up pretty darn well in our shop for being half the price of the original Tiger.

@Veikra 11 лет назад

*ducks out of the way of any possibly thrown computer monitors*

@tonyshook2624 6 лет назад

I BET HOME BOY HAS BEARINGS LAYING DOWN INSIDE THE CUPS . THOSE CUPS WEREN'T INSTALLED ALL THE WAY. OTC BALL JOINT PRESS 120 BUCKS WITH AIR TOOLS PREFERABLY.

@smileyrod11 8 лет назад

i use a hammer a vise them out

@MrRahimhosein 6 лет назад

pedro rodriguez english please

@brainwashed7244 4 года назад

sneaky!! notice skipped complete installation @ 4:39???

@mr.bojangles9840 3 года назад

I saw that to. Was wondering if it was done on purpose or if he made a mistake?

@AZDESERT2024 5 лет назад

The caps in the shaft ears, aren't even flush.

@pengchengwang5606 9 лет назад

puller is good. Installer canbe replaced by shop vise.

@terrinewman7390 6 лет назад

the installer is just a modified c-clamp

@jeepsblackpowderandlights4305 3 года назад

Cool video but expensive.. Id rather take a 5 lbs sledge and smack the ears with the shafts on a angle and in two or three good whacks the cap will pop off.

@cbettridge 12 лет назад

I noticed you aren't using an impact gun on that.....can it handle an impact gun. It would make that job really go fast, making more money! This tool could pay for it self in no time.....speaking of that, how much does it retail for? Thanks

@heavyhemi390 7 лет назад

would this tool work on gm u joints.. instead of heating them up to get that plastic worm to shoot out!!!!!

@Satchmoeddie 8 лет назад

Why not make one that used a small bottle jack ram and hydraulically presses the part out???? I just used a big__s hydraulic puller set made by Backhawk back in the 1950s. Amazing stuff them old Blackhawk tools. Blackhawk even made a conduit bender that would bend 1/2 rigid"- 2" thinwall, and 2" rigid conduits and it was the size of a small suitcase, but it did weigh about 90 pounds. Their U Joint Pitman arm puller set had a portapower type hydraulic pump, and the same type clamp & ram assembly.

@dalestewart7733 7 лет назад

I've bent yokes pressing them out with a chinese 10 ton hydraulic press. I think a hammering action is better than brute force pressing. I might try an attachment for my long stroke air hammer.