Setting Steering Endpoints - Spektrum DX3 

Just realised I've referred back to this video every new car I've bought, thank you for making it its helped me out alot 👍

Really simple, easy to understand video. Thank you.

Very helpful ! - after replacing my servo and attempting end points incorrectly, the steering on my vorteks had completely stopped. I followed your vid now everything is good ! Thanks!

Great video thanks straightforward and to the point, thanks…

Awesome! Just what i was looking for. Thank you!

Thanks that worked perfectly 🥰

Same issue in my scx6. Thanks!

When calibrating the steering, should much attention be paid to the whining sound the servo makes when it maxes out? That sound seems to run pretty consistent to when the wheels can't turn any further. I feel that that sound is just as important as paying attention to where and when the wheels stop. More info on this would be appreciated. I have an Outkast 6S with stock Spectrum servo.

Hello. It does not smooth it, so that I can turn the wheel to the right by hand to full and it is impossible to use the remote contro to full when I won't settings endpoint stering. What is wrong? To left side is ok but to right is not. Is not full.

Awesome thank you! Bash on!

When I am in programming mode and I turn the wheel in the first step, then go to adjust the at rate. The knob does move the wheels. Any suggestions?

My steering got inverted somehow how do I reset it

thx this helps me a loth

Hi, thanks for your Video and help. I did it a bit too much and steering is now at ~80 percent. What do i need to come back to 150% and set it to 100% again?

Why can’t I adjust my steering when I turn right. Left is fine but it never does anything when I adjust it on the right side. It’s still 150%

Thanks!

Grate video! Does someone know why my steering is reversed on my kraton 6s? I have to switch the switch knob to R for it to be normal. It’s not a big deal, but kind of annoying. I have the DX3 with the SR6110AT. I’ve calibrated it a couple of times to try to fix it but I can’t seem to make it reverse bak. I’ve just bought it in used condition. Thanks!

What servo are you running?

The factory directions are horrible. It states to use ST TRIM to set end points when when it should say ST RATE. Thanks for your video!

Completely lost all steering on my DX3 (Losi Lasernut) and was about to throw it out but decided to check out RU-vid before doing so. This video was simple, straight to the point and very helpful. Thank you!

I can finally turn again instead of making a 30 point turn thank you so much

Extremely helpful. Thanks so much. You got right to the setup and were wo easy to follow. 🏆🏆

Thanks 👍

I wish Arrma had included these instructions, would have saved my burning out the servo on my "RTR" Infraction

Thank you so much for the video! you made my night. I can go to sleep 😁🤝

1st tutorial and i GOT it from your video, thanks so much VERY helpful

Thank you soooooo much . Just upgraded my super rock rey to 1/5 servo and was lost as to why it wasnt steering... Just used your vid now 100%🤘

This method totally turned off or changed my ESC settings. Granted it worked for the steering adjustments until the powered down (save method). But in turning the TX power back on, now the ESC no longer functions. How do I turn that back on ? 😵‍💫 Need I bind the whole system electronics again ? Tough to do with a broken RX. Obviously I did something wrong ! But I followed your instructions to the letter. But in turning the TX off and then on again I lost my ESC function ? Now after turning it on again I've lost all functions including steering ? A supposedly simple thing and now I have a dead $ 1,300. paper weight 😕 Now the local Hobby Store here in Alaska has determined the RX is no longer functioning ? How can this happen with a program fault ? I did nothing electrical to cause it harm or for it to malfunction ? Unless programing it can cause damage to electrical components ? I'm both perplexed and mystified ! 🤨 My advice to others don't follow this "How to" instructional video.

My ol ass DX3E is a better controller End points don't reach the end on my SCX102 25% of the knob turn doesn't move the servo in the end position

Great information on setting end points on stock radio system.

Does this work for throttle in points too??

I just installed rear stear on my losi lmt-10. I can't get the servo saver on it strait. I'm wondering if there's a way to trim a 2nd servo on this dx3 transmitter?

Perfect thanks

Amazing thanks so kuch

Very helpful!!!

Very helpful. Thx

I have the same as that controller. My problem is My controller keeps beeping after I drive my racecar for like, 5 minute

Need help brand new remote, just did the binding, and the remote battery indicator lights are flashing green and beeping??? But car is working, Please not I can put the same two batteries in my infraction and the remote on the one has no battery indicator lights at all?

I have problem with my axial ryft. Hope this will fix it. Thanks😀

Right now my nob is set to avc. Will this still work and if so will my avc still work after I do this?

Thanks man!

Thank u

Super helpful info thanx

Thanks great vid.

After doing this my button on the remote switched from an avc button to a steering limit button how do I fix that so I can set my avc again..??

Ciao! Il video è molto interessante. Complimenti. Io ho un altro problema però. Non riesco a visualizzare il livello di batteria sul radiocomando. Sto impazzendo! Potrebbe essere una questione di aggiornamento di esc e radiocomando? Grazie.

Should the 3 other knobs be turned all the way down or up ?

Perfect!

How do I set the speed end points for crawler/rock racer

Did you have to bind and recalibrate after?