Sidewall Flashing 

Hi Ricky. I’m not sure there is an easy way to continue the kerf all the way into your inside corners, unless, like you said, you go extra deep with your grinder. They do make a diamond carbide blade for the multitool or oscillating tool (whichever term you prefer) which will cut brick and mortar and get into 90 degree corners. I think what I would do is to transition the flashing at the point you can no longer cut the kerf to the desired depth (probably just a couple of inches short of the inside corner). At that point, I would snip the metal that is bent 90 degrees to go back into the kerf and bend the remaining distance down 180 degrees. Put butyl tape on this bent down portion, face- fasten this to the wall and apply silicon sealant along the top edge of the flashing and against the wall. For extra pressure against the wall, and therefore a better seal, you could put a rigid piece of metal between the screw(s) and the flashing metal. Hope this helps and your project goes well. Thanks for your question.

Happy to hear you found the video helpful and thank you for taking the time to leave a comment with such a positive tone...not usually the case here on RU-vid! Best of luck to you in your future :)

Glad you enjoyed the video. Those nail clips are simply called nail clips.

@@KasselandIrons I've definitely tried a good number of searching using most associate terms to find anyone that sells anything like it. Please let me know if you have ideas on ways to procure anything like those (manufactures or product names). Most searches show either beauty care products or AV / low voltage clips... www.google.com/search?q=nail+clips&rlz=1C1CHBF_enUS805US807&oq=nail+clips+&aqs=chrome..69i57j0l7.3911j0j7&sourceid=chrome&ie=UTF-8

@@stacktier8257 Ah, I can see why these would be hard to find via a Google search! We do sell these in packs of 100 for $9.41. If you would like to send me an email at ryan.bell@isaiahindustries.com with your name and location I will get you in touch with our appropriate customer support specialist for your area to get you what you need.

i dont know if we cut a thin chase into the bricks like this in australia but i like the nice straight line of the cut shown here in part because it would be way faster to fit a linear flashing than stepping it. we flash over the roof sheets not under the roof sheets like theyve done here!

Doesn't matter boys as longest the shit don't leak n u get paid. I've done it both ways it works . What I hate is when jerk slap 2 gallons of tar around the chimney to make it water proof lol

yes step flashings are nice work and finish up well but straight line cuts are better look looking then exterior bead slapped on to red brick stacks and rendered up bout 2 to 3 inches i see that alot in Ireland ...liking these abutment pieces tbh... clean proffessional finish.

The flashings shown in the KasselWood installation training video series are all proprietary flashings we manufacture for use with our metal roof systems. If you’d be interested in seeing if this flashing will work for you, or possibly have us make something custom for you, please call us at 1-800-543-8938.

flat roof pitched roof they only share a few of the same roofing flashings sidewalls usually are about the same

It's a flat roof in the middle that is leaking. And with the snow and Ice it's hard to tell where its coming from

flat roof...you need a video for me to see. the truth is flat roofing you have to see it..or an easy fix would be henry elastomeric coating for a sealer..cheap easy diy..hind aluminum with no riber as a primer is important and the roomust be bone dry even in the crevices and 2 thin coats better than 1 thick one..and thin fiberglass flees helps in bad spots you dont know how to repair also low spots need to be filled in for a good repair..

depends if the customer requests it

not here in Indiana it wouldn't be. many roofers do it. I've seen it done in a few States. however. I could understand if it is historical.

Thanks for the comment Al. Yes, the shingles will then overlap and cover the nail clips.

The channel is designed to receive the metal shingles which have a formed thickness to them. The leg of the flashing that goes up the wall would then go behind the siding and the siding would be received into a channel that matches the siding, rather than the roof. On brick walls, the flashing would be bet and inserted into a kerf that has been saw cut into the masonry.