My shop projects are all about fixing problems I find as I spend more time in the shop. In this video, I address a lack of tool storage and workshop layout issue I've dealt with for too long.
Nice to see someone make "shop" cabinets/counters. Seems like far too many people get caught up on building stuff that's better and costlier than the cabinets in 98% of kitchens. Yours look good and a are functional. Not to mention lower cost. Which let's you put money towards more important items. Thanks for the video!
Nice solution to one of those oddball spaces we always seem to be stuck with in setting up a shop. I particularly like the frame/ panel construction for the sides and middle dividers. Didn't know Freud made the box joint set and will look into it. My shop floor is WAY too uneven, so I would likely need to assembly the frames as a unit with a toe kick/ platform (and a few stretchers) to set the whole deal on. The pocket whole frame assembly also seems like a great 'practice' project for other 2x lumber.
Thank you! I've been really happy with it since. Yes, this was a great way to get rid of some of the scrap 2x material that was just laying around. I haven't had another dado stack, but I've been very happy with this one so far.
At some point, that top will warp where the gaps are between the shims. If that happens, and you replace the top, I would suggest leveling the legs instead. Find the high spot in the floor, and mark level across the wall. Run all the legs up to it, leveling and shimming as needed. When you put the top back on, it will now be flat on the supports.
Very similar to my smaller basement L-shaped shop (~400 sq. ft.), but I got a super deal on Rockler steel shop stands for my bases. I topped & sided them with 3/4" plywood and edge banded with pine just like you did. Nice and robust. 11:22... single best cheaper purchase I made was a 25' heavy duty electrical reel cord that I mounted in the ceiling dead center of my shop above my table saw outfeed/assembly table (12GA, full 15A, not those cheap 10A models that the builtin breakers trip all the time) . I can pull the cord anywhere and reach every inch of the space, even though I have outlets all around each wall.
I recently did that with a hose reel for my air compressor from harbor freight and am very happy with it. I'd get an extension cord reel too but I have enough outlets in my shop that I almost never need an extension chord lol.
Great solution to your specific needs. I think I would have leveled all the "legs" before attaching them to the wall thus avoiding the shimming of the top.
Thank you! Yeah, I think that I could've done that better. It would be difficult to square them prior to install based on the construction method. But if that was a bigger priority, I may have added identical stretchers to everything and then level them together. Overall though, I'm very happy with the end product and have no regrets on it.
Great ideas and video. Thank you. I'm thinking of doing something like this in my small workshop. Do you experience a need for doors (or something similar) to avoid dust coming into your drawers?
Good question! So I just have my systainers in these which have lids on them (they're boxes) so it's not a big deal. But there's very minimal saw dust on top of them when I pull them out anyways so I really wouldn't be worried about it?
fire is a big hazard in any workshop, hence planning is needed: fire extnguishers but also a garden water hose but in that case care must be given to electrical wiring, it runs on the floor and will get in contact with water...an overall breaker for the whole workshop would be required. Any ideas as fire exting. will last 30-40 seconds and the workshop is full of dried wood and sawdust. what would you recommend ?
Great project. I really enjoyed watching the build. You have to do something with the sound level on the video. It's impossible to listen to in headphones. Had to adjust up or down multiple times through the video. Especially when ads cut in with deafening loudness compared to the sound level of the narration.
Thank you! Thanks for the feedback. So from your perspective, would the video sound level being higher resolve that? Being more aligned to what the ad volume is?
Sometimes I think how I'd just like 4 more feet (bald eagle wings spans) in both directions, and then I see othe shop tours or hear things like this and feel very thankful! 12x20 is a pretty standard one car garage/large shed over here.
Most floors are not perfectly square and level. Instead of shimming the countertop level most cabinet makers would use a footer and shim that level. This way you are building off a level platform for you cabinets to rest on. Shimming up the countertop like you did throws off the alignment of the cabinet and raises visual correction of floors lack of level from your toes upto a height where it becomes visually more obvious. While your method allowed you to utilize the full height between the countertop and the floor most people find having drawers or containers(systainers) raised a few inches easier to access.
A man doing work in sandals while wearing socks and uttering the phrase "came in clutch". Good instructional content, but sometimes the viewer has to suppress mild disappointment and watch on.
Asking this question to you too? Couldn’t we work in a space without the wood that awaits future projects hanging over our head and loitering in the corners around our feet?