Special Way To Sharpen Pruning Shears As Sharp As A Razor 

As a D.I.Y. enthusiasts and a creative individual I can't believe I hadn't come across the battery trick to removing rust. Thank you for this

I’ll just go and get new ones. Thank you

"Wow, this video was incredibly insightful! I never thought sharpening pruning shears could be this easy and effective. The step-by-step demonstration was clear and easy to follow. Thank you for sharing such valuable DIY knowledge!"

It would be easier to buy a new pair of cutters.!!!!

It's fine if you have the time, but sometimes time is money.

Good for restoring old school tools that were made of better metal.

You did well, my dear.

What is the purpose of using the AA battery as oppsed to say a similiar sized metal rod ti polish?

Ingenious! The creator must be an engineer. Only one point of correction, though, and it’s a pretty major point. The shears in the video are bypass pruning shears and the section on sharpening is incorrect. First, you do not need to sharpen the lower arm of bypass pruning shears. Only the upper arm does the actual cutting. Second and much more important, you should not sharpen both sides of the upper arm of bypass shears. For anvil shears, yes, but not for bypass shears. It will damage and dull the shears if you do. You should ONLY sharpen the angled (beveled) side. Once you are completely finished sharpening the angled side, you make ONE swipe on the other side - the flat side - with whatever you used for the final sharpening on the angled side. This is to remove any possible burrs. But that’s all. Some experts say not to even do that much - that just opening and closing the shears will remove any burrs on the flat side. Aside from that, I loved the video. The section on sharpening should be redone and the video titled, “A Geek’s Guide to Pruning Shears.”

I'm Looking from Östervåla Sweden very interesting video

Very good idea 😊 thanks from Türkiye

Use the center of the battery for sharpening it should work way better and can be used for welding as well😊

Incredible job 🎉

Excellent video. I have used this method to restore some vintage steel Tonka trucks, although I used washing soda instead of salt. Ignore the "experts" who have no respect for the thought and work that go into making your videos - if there is something truly unsafe or could be done a better way, let them say so politely.

Από ΕΛΛΑΔΑ ..ΝΗΣΟΣ ΕΥΒΟΙΑ ..ΘΑ ΤΟ ΔΟΚΙΜΑΣΩ..ΣΑΣ ΕΥΧΑΡΙΣΤΩ ΠΟΛΥ..ΕΛΠΙΖΩ ΝΑ ΤΟ ΚΑΤΑΦΕΡΩ!!!!!ΝΑ ΕΙΣΤΕ ΓΕΜΑΤΟΣ ΥΓΕΙΑ!!! 😮😊😅❤ 🕊️🌹🕊️😀🕊️🤝🕊️😄😃😀🙃🙃🙃🙃🙃

What liquid did you squirt onto the sandpaper at 6.19 ??

When he started to sand it with a power tool that was it for me.

Nice job! 🙂

Does the battery/salt water soaking process smell bad? Thanks for this video. It’s great to restore old tools to their usefulness.

I have never had a battery peal that easy either lol

Realmente el filo se pierde cuando las tijeras se separan

Nice...but $.99 @ the dollar store !😢

If your a Fred Sanford sure but cheaper to buy a new pair it would cost money to do this but the idea and knowledge is Very Very Valuable so Thank you. 😁

Oh your video is amazing, it's very useful for life❤❤❤

You can use purex instead of salt and 6 volt battery will do just fine. Use this to clean any rusted parts.

soak it in the transmission fluid with some salt you will be amazed of the cleaning power

Is it possible to use a smaller power supply?

$5 in materials 2hrs labor for a $15 topps pair of shears WTF

Soy de el salvador

Cool idea but... I wouldn't use one of my drills. All that crud being so close to the chuck... after a few times doing this you would seize up your drill.

Вітаю, друже, а як позбавитись іржі на авто, підкажи дієвий метод

Total waste of time!

I would prefer to buy new ones!!!

amazing

I can get the same or better with CLR soaked over night and you can get drum wheels instead of screwing your drill up. BS

အလွန်တန်ဖိုးရှိသော ပညာရပ်အတွက် လေးစားဂုဏ်ယူပါတယ် ခမျ

Note to those who didn't notice he cleaned NOT SHARPENED the Flat side. ONLY sharpen one side, the outside edge

well you got 379000 views in a day. sadly this information apart from the rust removal is very poor and i really would not recommend you use these methods.

What is the electrolyte solution?

Asal Lamongan Jawa Timur Indonesia

I can't believe this appeared on a Google news feed

Why do you supposed that we know what is the white material ?

Why the toothpaste?

Que el lo que hace la y la electricidad

What's wrong with a wire brush and some light oil?

Definitely easier to buy new ones who could be stuffed doing all that

2k24 year, seriously?

Interesting but way to much work for $10 pruners

A lot’s of work

Que ha la pila?

🤗👍👌💯

Unsafe....

When in India...do without

Useless the battery system it's nothing? It's better to sharpen it to the grinder. Nonesence this sample of doing?

This chap took everybody for a ride he is interested in getting likes to get money from RU-vid!

😂😂😂 so you got all the people watch that nonsense, what a smart way to make money on RU-vid 😜

rohadjatok meg a reklámjaitokkal

Good good 🎉🎉🎉🎉

Waste of good time!!

Did not watch took to long my pets demanded lots of attention

There is at LEAST a 1000 better ways to waste time than this method or vid 👎

SUCH BULLSHIT!!!

Load of bull shite

Worst video I’ve ever seen 🤦🏻 time wasted I will never get back 👎🏽🤨

🎉🎉