Sta-Rite Motor and Pump Seal Replacement: How to change a Motor and Pump Seal on Dura-Glas Pool Pump 

Very complete. Always had good camera angles to see everything that was being done. Good advice along the way. I learned several simple, but key items that made may efforts successful. The only thing I found different was that I was able to fit the 7/16 inch wrench behind the centrifugal switch, without removing the "white V-shaped" switch. Thanks for the video!

Those were the best pumps Ever made i bought two Of them still use them today

I have watched your video multiple times over the past few years, and I just want to say thank you for sharing it! I had a really bad leak coming from the connection between the motor and housing, and it is now dry as a bone. The key was putting in the silicone behind the main oring gasket, which did keep it from falling out. The Century motors are a little different now with no switch, but I can tell you this video is a great tutorial on how to replace everything you need for a StaRite Dura Glass 2!

Thank you so much!!!!! It was so helpful

At about 5:35 you take the plate off the motor but do not specify how. I tried prying and gentle tapping but it doesn't move. I'm afraid of cracking it. How did you do it?

Is the cone part necessary? I accidentally broke the cone piece off but some of it is still left in there. The seal is good but now the cone part of the j3-2 is missing. Is it necessary to replace it or am I ok leaving it? Will it hamper performance?

What is the model number for the shaft seal you used? PS 100, 200, or 201?

What is the HP of that motor?

From one pool tech to another, thanks for the tip about tapping the ring clamp to make tightening it easier.

Good job. Thank you, Sir!

It took me about six or seven videos to find my exact situation and your video is nothing short of perfection. Thank you.!!

Thanks so much for this video. I was losing about a half inch of water a day. I just followed the procedure step by step to replace my seals and rings and it worked perfectly and saved me hundreds of dollars. Thank you!

You mentioned applying silicone to the Seal Plate O Ring. Do you mean the same type of silicone use in bathrooms for caulking? Or is there another type of silicone that needs to be used? Usually I use O ring lubricant (Magic Lube), but from what I understand in your video, O ring lubricant might not adhere as well as silicone.

I have a Max E Glas with a diffuser that looks just like this one. I have a salt water pool and the brass bushing in the diffuser is pitting badly and quickly . ( less then 6 months) . do you know of any better bushings/ repair ?

Great video, and VERY helpful! I ended up having to use the butt end of a 3/8" ratchet between the motor housing and the centrifugal spring mechanism on the shaft (mine add a screw in the shaft, not a 7/16" squared off shaft grabbing point) at the rear of the motor in order to get the impeller off. It was a pain and was getting stressful, as I was trying a number of things before I determined that a firm, metal ratchet handle end would fit just right between a recessed area of the motor and the spring mechanism. Everything else went exactly as you described - thank you!

note- on my previous comment I had installed a new diffuser and pump wheel and tried to center the pump in the diffuser when i installed it.

Thanks for the great video... I have a Sta-Rite P2R pump that developed a vigorous spray coming from a several inch section under the ring clamp. Water begins dripping almost immediately when the pump is turned on, and turns into a hard spray as the pressure builds. I replaced the seal plate o-ring, cleaned the seal surface (both sides) and the channel for the o-ring, and lubed the o-ring with silicone plumber's grease. I also cleaned and lightly greased the inner side of the lock-ring clamp to reduce friction and got it pretty tight on there. Unfortunately there was absolutely no change in the force of water spraying out. Could it be something besides the o-ring and clamp?

Thanks for the good information, my unit is pre-1998(1986) you mention the J3-2 seal plate insert. I have replaced the motor a couple times but I have never seen this seal plate insert, how important is it? and where is it actually located? Great Video.

Thank you so much for making this video, following it exactly has helped me twice now......a little advice for everyone that's using this as a guide.....save it to a play list, you will need it MUCH sooner than you hope, these motors typically don't last long even when installed correctly. This is by far the best instructional video for this exact pump motor replacement.

Tapping the ring clamp to make tightening it easier is a good tip. I have used pool lube around the plates where the ring seats. Also allows for a nice tight squeeze.

I replaced everything and it started right up with no ,waking. After about a minute it started to smoke a little bit and smelled burnt. Not from the pump motor area but under where it was previously leaking water. Is it possible the impeller was put on too tight?

I found the hard way that tapping the clamp with a rubber mallet as you tighten finally sealed the unit after numerous tries. Wish I had seen your comment about tapping the clamp before hand. Thanks for just a great video!

I've heard a number of times to "not touch the ceramic seal surface with your fingers" when installing, it will cause the seal to fail. I noticed you didn't seem too overly concerned about that and did not mention it during your excellent tutorial. Is touching the seal surface a real concern or is that just a myth? Of course I do understand that the seal must not be contaminated with grime, but will touching it with clean hands/fingers shorten the life or otherwise ruin the seal? Thank you for the excellent video. I have successfully replaced a seal before, but the tapping of the lock ring clamp with the screwdriver handle is a tip I did not know and I will use the next time.

I had to empty the basket under the dome, but I can’t get the dome lid back on. I have plugs in the skimmer and the output (idk the term for that). There is a trickle of water still getting through, but what in the world do I need to do to get that thing back on?

hi location po sir

V nice video. My pool pump is 1997 built. I am replacing the motor and have ordered it. I have a feeling the seal kit is for pumps after 1998. Will that be a problem ??

Great video BTW, can you tell me if the shaft plate O ring on the pump you serviced has a square cut? I have a similar pump, but once I removed the seal somehow is now longer and I’m having a hard time trying to get the correct part to finish this project. Thank you

Is the seal insert absolutely necessary to replace? I have a Sta-Rite Dura-Glas pump assembly which is post 1998 ..... I needed to replace the faceplate that attaches to the motor. My old one didn't have the insert and the replacement did. Can I just do away with the copper insert? I have to change the shaft seal because I have a leak. I already replaced the diffuser o-ring and faceplate o-ring and that didn't stop the leaking so the shaft seal is the only thing left to replace. Thanks for you guidance! In these Texas temps this summer, I need to get my pool back to normal.

After seal replacement is it supposed to seal 100%. I don't see water dripping, but if I feel with my hand after it runs for over 15 minutes I can feel some water seeping.

Very helpful video, what kit did you get?