STALKER Kraken TAC-41 TDC Hopup Chamber Installation Video Short 

thank u!

Niksu, Good you are watching this video, next week we will make a in depth video about the installation and features. Many thanks for purchasing our product, it means you can expect more of these kind of upgrades on the market. Have a good day!

@@stalkerairsoftdesigns5716 Cheers! Looking forward for the in dept video.

Had you beat, skirmshop accidentally put it up 3 weeks ago and I bought it super excited then got an email that it wasn't available yet

i probably buy it before one minute sorry but nice try

Hi Chris, did you find the answer to this question?

hi thanks for asking. its not a 3rd screw. its the 1st and 2nd screw over and over again just a little bit until the set centers itself. it would be good to tighten one side completely and then the other set. so we advice to do it switched and devide the turns over the two screws until the inner barrel centeres and both screws get tightened at the same time.

It does not come with the kraken, we designed it to use in our tech department. If people like it we can release it maybe.

Especially that the cylinder head is a custom Stalker one, that tool should have been included in the hop up package, like silverback did for their cylinder head. 3d printing this would be a pretty low cost and would have been a nice touch considering the price of the hop up unjt

@@stalkerairsoftdesigns5716 Please do! Its kinda nice to have a tool perfectly designed around the cylinder head and to also have an easier grasp on putting the cylinder head on.

I will do it, have to see what kind of material i can use to make it affordable for the airsoft. TBC 🤘🏻

You can find complete upgrade kits with our inner barrel on www.skirmshop.nl Oir TDC unit works with GBB/VSR style barrel only

@@stalkerairsoftdesigns5716 thank you

No, its totaly fine! You need to check which O-ring fits the best on your cylinder because we think not all cylinders have the same diameter so we included two different O-rings for the cylinder head. 1 small, 1 bigger. For the screws, the pointy grub screws are for inner barrels with a small side cut, the flat grub screws are for stalker morpheus inner barrels and align the inner barrel a little better with big flat grub screws. Game on!

We made some for our tech department and using it for over a half year now. Its nice and strong! Maybe we should release it for the public..

@@stalkerairsoftdesigns5716 pls i need this

advice to use the stalker barrel cause all parts we make are made for eachother but, you can use our hopup with other GBB open cut barrels sometimes but the best performance you get out of our complete set because its made for eachother.

IF your bolt does not go down like normal but stif, then sand this bolt nut a bit down. This is the reason why your TAC41 is so silent after this installation, you make a FIXED setup so your bolt set does not wobble or moves when you are shooting. this means your setup is fixed and steady between receiver and front of hopup. all the shocks go trough the rubbers and there you go ;) good luck!

@@stalkerairsoftdesigns5716 thanks for the info, I have sanded it down but now after a few shots the spring guide stopper starts to pop out and I am unable to pull back on the bolt. Any advice?

@@benchapman2703 Hello, then you are probably use a short spring for the TAC41, maybe you can use rapax lightpull, silverback spring length or similar length spring, then your problem is solved. You can use short springs like rapax RMS but then you need a thicker bumper pad in the cylinderhead, we sell them in 3mm, 5mm or 7mm and right now you have 3mm. 5mm will eat a bite more volume but its a thicker rubber so it will absorb the impact of a piston slightly more than a 3mm rubber. The spring guide stopper of the TAC-41 needs the tension of the spring to be able to kept in place, if u use a shorter spring then you change the tension and then the guide stopper can wobble or in worst case, can fall out. You can choose one of the methods we wrote above and the spring guide stopper will be kept in place.👍🏻

@@stalkerairsoftdesigns5716 So I am using a Silverback m150 spring, do you think I need to switch it to a Rapax 2.2 spring?

@@benchapman2703 i use it myself as well works like a charm

hi there thanks for upgrading with our parts. the thing you notice is normal, its called joule creep :) you can read a lot about it on internet.

www.skirmshop.nl/en/anti-shock-rubber-pad-set-3mm-111915562.html

Ce petit joint beaucoup de gens vont le négliger pourtant ca va faire toute la différence niveau son

vous pouvez simplement utiliser l'épaisseur que vous voulez, il existe différentes épaisseurs disponibles. l'épaisseur que vous obtenez est de 3 mm