No video :(

Starts Then Cuts Out Immediately - No Tools Required DIY Solution!

Подписаться 122 тыс.

Просмотров 505 тыс.

50% 1

If you have a Toyota in particular and your vehicle starts but dies straight away? Try this simple unplug method to confirm if the Mass Air Flow MAF sensor is the fault.
If I helped ya out? or just enjoy the content & you would like to buy me a drink ko-fi.com/gera...
Tool options that I recommend and use - www.amazon.co....
➢ For business inquiries Email : gerardburkebusinessinquiries@gmail.com
Disclaimer:
GerardBurke is a qualified motor technician who has completed modules & courses in manual handling and all aspects of workshop safety. These videos are not intended to be used by anyone who is not trained and or qualified to carry them out.
Due to factors beyond the control of GerardBurke, I cannot guarantee against improper use or unauthorized modifications of this information. GerardBurke assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. GerardBurke recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of GerardBurke, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not GerardBurke.
#Toyota #StartsThenDies #DIYDiagnostic

Опубликовано:

21 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 205

@chansasalimu9007 2 года назад

This video just saved my day. I noticed my car was vibrating and it went off in its own. It couldn't maintain idle. After watching this video, I disconnected the MAF sensor and boom, I was on my way. Thanks a lot. I was 30KM From safety.

@saucyg407 8 месяцев назад

I’m about to try this I hope it works I’m 54 miles away from home in the rain with my girlfriend

@djohntalks Месяц назад

@@saucyg407did you reach home?

@jeffwelter3055 Год назад

Thank you so much for the video. This helped me fix our 2005 Sequoia. It was starting and then dying after like 1 second but we could usually getting going on the 3rd or 4th time. Did this for a few weeks and then it it would be okay for a while. But then it started dying while driving while at a red light, etc. Took it into the shop and of course it wouldn't do it for them. They kept if for a week and it never acted up so they didn't try to fix it because they said it was fine. Then today it wouldn't start and run at all. It would start and then run for 1 second and then die. I was thinking of having it towed into the shop, but I thought I would check youtube first and found your video. Tried unhooking the MAF and it started and ran no problem. Got a new MAF, changed it out in like 3 minutes and now all is good and running fine again. Thanks again, Jeff

@olanrewajuoladokun3133 4 месяца назад

😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊😊

@coachdove Год назад

Saved the day! Tundra wouldn’t start this morning. Pulled up this video on youtube, and presto! Started right up after disconnecting MAF sensor. Thanks!

@supernaught1963 Год назад

This! Held on to my Sienna because it would start up then die. I use this as a work van and I love it. After months of trying to find the problem, I came across this solution. Wallah! Thank you so much. You literally saved me thousands (for a new van).

@xovoiids3392 4 месяца назад

This worked on my 02 century after I changed the spark plugs and fuel injectors! It would start up for a second and then shut off completely. It took me so long to figure out what it was and this video stands a test to time and helped me out years later after it was uploaded. Awesome diagnosis. 🎉🎉

@trythis2821 Год назад

Good to know car runs without MAF connected. Good preventative maintenance to clean with MAF sensor cleaner every one or two service intervals.

@fieldsofomagh 4 года назад

It's like making a list for the supermarket, great so long as you remember to bring it. However for a motorist a long ways from home, and stuck out in the wilds, its a very handy, low tech solution and very simple to carry out and get someone on track again. As they say at Tesco's, "every little helps".

@GerardBurkeBurkesGarage 4 года назад

Spot on Tom 😉👍

@atticusspontaneous Год назад

Thank you Gerard! I couldn't figure out my issue after installing a CAI on my Fairlady Z. As soon as you showed me, I unplugged my MAP and voila! Lol Gonna replace it tomorrow 🤘🏻

@sojourn20 10 месяцев назад

Found it useful? Man it’s great 2005 x trail doing this . Just pulled the sensor and it runs. Thank you so much

@norisboren5402 Год назад

MAF (near engine air filter) cleaner & THRODDLE BODY cleaner needed. A Mechanic can clean the grime off both ( not easy) about every 25,000 miles or 1 1/2 yrs.(change engine air filter then also). If replacing parts keep old parts. Hope helps.

@rodericksmith5662 Год назад

Great video. Showed the symptom, possible solution, thorough, and under 5 min. Thanks!

@vanguardoftruth4166 2 года назад

Dude thank you! There was a fly in my MAFS! I couldnt understand what was going on!

@sdkaehler5212 Месяц назад

I experienced this exact problem yesterday and followed the steps indicated to confirm the problem was the MAF sensor. Bought and installed a new one and the van seemed to run fine. For one day! Then the same behavior returned now with a new MAF sensor. When I disconnected it this time, the stalling persisted and I am now seeing DTCs P0351-P0356 (before disconnecting the MAF sensor).

@ibrahimharoon9968 5 месяцев назад

Great .. just now my car happened this issue. Then I search in RU-vid and I see your video.. really I follow that and my car issue successfully.. right now I gonna subscribe your channel.. thank you sir

@MiguelBricaBrac 7 месяцев назад

Wow, is only my issues with vehicle were this easy to remedy. Great video, thank you for sharing.

@Damianzw 10 месяцев назад

Had this exact problem in 86.Thank you heaps

@stevofromiowa 2 года назад

That worked for me. Thanks! And for everyone else, these things will cause a hard or no start as well if they're dirty. Spray the sensor down with some CRC QD Electronic Cleaner or equivalent. In my case, it saved me from having to buy a new sensor.

@tonetell3095 2 года назад

Why didn't he say it in this video

@stevofromiowa 2 года назад

@@tonetell3095 I know, right? Dirty sensors are a common problem. My experience has been that if someone else is buying the parts, it's much easier to just throw a new one at it. Plus the shop gets 50-100% markup on the part. But I will say that the shop has an interest in getting the problem fixed right the first time, where we DIY'ers' interest is in saving money and not buying unnecessary parts if we don't have to.

@maungmaung4037 Год назад

Not always I cleaned my sensor not good at new it show 0.3 gram per sec when engine stop. Pretty sure out of calibration.

@lorenolson2069 Год назад

2009 Chevy Traverse, that was the problem exactly, saved me tons of time and headache.

@804eyes 4 месяца назад

4/2024 this video helped me with my Lexus sc430 THANK YOU from PHX AZ

@Inner-peacee Год назад

You just saved my life 😢 car on the move thank you so much

@matthewwilson9085 7 месяцев назад

I have a Kia optima 2010 this same thing happened to me I watched this video and it saved the day thank you so much

@gregstoloski6865 Год назад

I had been in so many conversations, reading so many forums, trouble shooting several other solutions and this was it Thanks so much for this.

@mangamangah974 2 года назад

Very useful thanks. My Avensis is also doing that I have to get it checked…. A lot of thanks from South Africa

@HeirloomReviews 2 года назад

Thumbs up! this happened maybe a year ago an i forgot all about it after i changed the MAF now a year later it happened again! the first one costed $144 an now i got to do it again? can i leave it disconnected? Thanks a million really helped

@Lucentlens Год назад

If you have a Toyota diesel - this exact symptom is that of a sticking SCV (Suction Control Valve).

@leonmagnus00000 7 месяцев назад

Have a 1kz that's doing this. Is this the spill valve you talk about?

@lyndaleetqpv 5 месяцев назад

Thank you for your tip I'm going to go try it right now and see if it works out on my Silverado

@daniellepage2923 9 месяцев назад

Thank you. I have a 2018 volvo VNL semi-tractor D13 motor. This was exactly the issue.

@HilaryMullings-kr3et 7 месяцев назад

Thanks for this video. Had the problem with my nissan serena i used some wd40 electronic spray to clean the air flow sensor and my problem was solved.

@JoeBob79569 2 года назад

I'm having this issue with my 2.2D X-Type but unplugging the MAF didn't do the trick, but unplugging the wire to the turbo actuator did get it going. It will also start when I unplug the MAP on the EGR, and once it runs it will be fine starting up again, until the next day. But it's running really rough, searching, erratic gear shifts (automatic), and lots of different random error codes, like torque signal, neutral shift position, high fuel pressure, etc. I'm starting to think it might be a ground issue.

@AlejandroLopez-ic5cr Месяц назад

Same here bro

@malaajam 2 года назад

I've started getting a problem on these cold mornings with my 2007 corolla verso 2.2 Diesel will start the first time without a problem and idle normally. After about one minute or so warning light will show up on the dash than fter another 30 seconds the engine cuts out. When the engine dies, I can restart again without a problem and the whole scenario starts over this happen until the engine warms up. once the temperature reaches 60 and the blue light goes off the car works fine the rest of the day. I cleaned the EGR, polished the glow plugs and tested them, put a new fuel filter, tried a working SCV from my mate's car, and did a full tank with fuel treatments. None of the above-mentioned worked however the car performance is much better. I tried to warm up the fuel rail line with a hot cloth soaked in hot water and will top it with hot water every now and then and the car did not cut off but won't drive as normal unless the engine itself is warmed up. Once it is warmed up it runs fine. Any idea what else could it be? Thank you

@johncollins8304 Год назад

Yabadabadoo! 2005 Opel Tigra Twintop, Corsa engine. Fuel holding at 50 psi, new plugs, all new filters, pump.. Cuts out in seconds.Tried to get MAF spray in France, never heard of it. Cheap Odb reader useless. Tried to buy XTool D7, not in France, and Amazon won't post here from UK or US because its a "non digital item" (???). Managed to unplug (weird one) ran for 30 seconds, shaking, all warning lights went out. REplugged, cut out. So this doodad is prolly beyond cleaning and needs replacing. Will bookmark this and update. Thank you sooooo much.

@user-nw8rg8th7o 2 дня назад

2000 corolla, mine does the same thing. Replaced the MAF with OEM. Still does it

@frankjoncona4018 9 месяцев назад

great video, diagnosed my problem perfectly. Had it fixed within an hour!! THANK YOU!

@callofgeorge Месяц назад

omg if this is all it ends up being on the car im working on i'll be both pissed and relieved.. i've swapped cam position sensors and crank position sensor on the advice of other mechanics.. i never once thought the maf would cause this without throwing a code. mine does this but only after the under hood temps get hot. if i keep a fan on top of the engine it'll stay running so i figured it was a sensor.. thanks for the video.

@key-bn1xx 3 года назад

will a bad MAF sensor stop the engine from being able to rev up whilst depressing the gas pedal and starting up the car? iv got a 98 v6 sr5 4runner

@tomdipasquale4744 2 года назад

Great video.i fixed my car un 15 seconds.thank you.great.

@brianpemberton3811 2 года назад

I love you… you are a lifesaver and my hero

@brianpemberton3811 2 года назад

Seriously Louisiana heat ain’t no joke thank you!!!!!!!!

@scottdoherty6148 2 года назад

Car ran fine. Filled up at gas station, then car wouldn`t stay running. Thought it might be bad gas. Opened the glove compartment and smuggly staring me down was a damn rat! Thought that bugger maybe chewed through some wires. Found your video and unplugged MAF sensor; my baby started right up!!! Thank you so much! I still have a damn rat in there somewhere. Any videos for that?

@twostroketom 4 года назад

Nice tip Ger, might come in handy for the Dad's Avensis sometime and get him home. The new intro is class btw 👍👍

@GerardBurkeBurkesGarage 4 года назад

Always a good one to keep in the back of your mind, only issue is trying to remember it when the time comes 😂 Thanks for the feedback on the intro, I spent so much time to get it how I liked it so it's great to hear feedback ❤️❤️🙏🙏

@twostroketom 4 года назад

@@GerardBurkeBurkesGarage Yeah, the auld memories aren't the best so we'll probably spend a few hours unplugging everything until we hit on the right one. I'll have to put a sticker on it for him. 😁 You'd definitely know that time was put into the intro - lovely design on the car and look of the logo generally, nice timing on the cog rotation and the name sliding in, syncing with the sounds of the windy gun, then the knife slice and the shimmer to finish. When you retire from the wrenching, you'll have a career in graphic design/media ahead of you, very professional looking. Nice one. 👍

@GerardBurkeBurkesGarage 4 года назад

@@twostroketom very kind mate thanks 🙏🙏🙏😊😁

@cinema6r845 3 года назад

I have a 92 lexus sc400 obd1. Since its a toyota as well i need to try that. I have replaced many electrical, fuel related parts and all the vaccum line i could find when the car has different symptoms but bow it's doing the exact same thing as this car. Only difference is if I unplug the battery and reset it'll stay on a little longer but repeat again.

@oldguy8177able 8 месяцев назад

thank you,i sprayed contact cleanner on terminal fixed

@davidphilip6674 4 года назад

Thanks for your honest helping.

@GerardBurkeBurkesGarage 4 года назад

Thanks for the kind words David ❤️🙏🙏❤️

@michaelcourter5432 2 года назад

What happens when you unplug the sensory and drive?

@iosbypassnz7854 Год назад

The ecu won't read how much is air coming into the engine that's why you need a MAF sensor. And if you drive with the mass air flow sensor unplugged you will see black smoke coming out of your exhaust pipe.

@MarvinxJavier 2 года назад

Wow, thanks a lot, this is very helpful in troubleshooting.

@rowlandaloriba6931 Месяц назад

You saved me. Thank you.

@wickedpossession7635 Год назад

Have this same problem with a 2009 toyota venza. Starts up and immediately stalls. Try to start again without turning it all the way off and it just cranks without turning over... If I turn it all the way off (push button) it will do the start and stall again. Unplugging the maf sensor does nothing to change this. It actually did this to me months ago...then suddenly started working again until about 3 days ago. Can't get it going

@hollylaureano2860 6 месяцев назад

Check for dirty battery terminals or change the battery.

@tiberio1352 5 месяцев назад

Dear Gerard, my camry 95....starts, runs well, but ONLY sometimes AS it's coming to a stop at a light, for example, DIES. .it takes a couple of minutes to restart. Or as it happened last night , car coasting to a stop it went dead. Since it has happened 4 times in a month...any guessings what needs to be checked?? Thank you man. GREAT video.

@msc807 Год назад

In my case I unplugged the fuel pump and let the air come out Then it started properly

@ScottyFrfr Год назад

Thank you O wise one if anyone hasnt told you yet you are a miracle an miracle worker thank you for your advice an knowledge may your journey be long peaceful and prosperous #lifesaver

@conorcousins27 4 года назад

Have they the hot wire air flow meter in em ger..u can clean the little hot wire element in the air flow meter with carb cleaner..ive done that on the yaris before and it works a treat

@GerardBurkeBurkesGarage 4 года назад

Spot on Conor, as I say at around the 2:44 mark, have it replaced or cleaned up. Whichever is more suitable for your circumstances 👌👍

@paulsaxby7368 4 года назад

Excellent experienced knowledge shared once again, many thanks.

@GerardBurkeBurkesGarage 4 года назад

Appreciate you saying those kind words Paul. Thank you :)

@mikedelta658 Год назад

mine has the same problem like this and solved by changing the mass airflow sensor!

@vodonnell1 4 года назад

Useful information, thank you!!

@GerardBurkeBurkesGarage 4 года назад

Thanks Vincent 🙌👍

@chiron6699 Год назад

Thanks saved me a big headache 🙂

@GerardBurkeBurkesGarage Год назад

🙏🙏

@austinsoutdooradventuresan2338 3 года назад

What if I already replaced the mass air flow sensor and the problem continues

@RogueEntertainment 2 года назад

You find a answer to this?

@austinsoutdooradventuresan2338 2 года назад

@@RogueEntertainment actually I did you have an electric plunger in the front of the block of the engine with a big tube coming out that leads to the air filter I popped that tube off and saw a lot of build up of carbon along the plunger if you half turn on that key the plunger will open use carb cleaner and clean it really good out it all back together and I’ve never had the issue again

@austinsoutdooradventuresan2338 2 года назад

@@RogueEntertainment lmk if you need help finding out what I’m talking about

@RogueEntertainment 2 года назад

@@austinsoutdooradventuresan2338 Thanks man, I'll check on my car and see if this works.

@CameronBatten-yg7nw 6 месяцев назад

Thank fixed it myself

@Interknetz 2 года назад

Mine does this, except it dies far more immediately to the point you can keep the key turned and it'll keep trying to start and die within half a second each time.

@rogerdodger8813 2 года назад

My car 2007 Camry, is currently at the mechanics being diagnosed for this issue. They said nothing appears on their computer. I suggested the MAFS after watching this video, hopes it's the issue.

@williamferrante3855 2 года назад

So what fixed it?

@xxmaddog_madaraxx 2 года назад

My GX470 does the same exact thing, starts then it'll stall out.. I was stranded at the gas station waiting for a tow truck, but I was parked where the truck wouldn't have been able to get in front of my vehicle.. I randomly decided to try to move back just a little bit so the truck could get into position. After starting, I went into reverse immediately after starting up & it STAYS on . It's the only way it stays on, park or drive or driving/doing nothing after starting will make it stall out and turn off. Any ideas what this could be? 🤔🤔

@mikee8304 Год назад

Mine was the air box wasn’t connected correctly to the throttle body

@xxmaddog_madaraxx Год назад

@@mikee8304 idk what my issue was, but luckily I knew a guy who just removed my throttle body and cleaned it with SEAFOAM then put the SEAFOAM inside my gas tank and gave it a good powerbrake

@mikespaintedminis5100 Год назад

I’m getting this with my 2014 Qashqai it’s had the air, oil and fuel filters replaced

@user-gj4rq7lc5c 7 месяцев назад

Thanks for the video It’s very helpful

@cookinghard1 2 года назад

I'm having that exact same issue right now with a 1997 Plymouth Voyager and what I seem to do to fix it is I removed my glove box area actually I'm removed my glove box and I was able to view my heater core housing unit and what seemed to be I guess maybe a problem is the cord to my heater core was pushed in that could be why it was stalling out when I was started I would start it and it was solo immediately and what I did is I pulled the cord close to the what looks like to be flush with what it was before it was pushed in and I started it and it worked now today my wife is in the city 1 hour away and she phones me and she says the van won't start I said well try what I told you because I think that's a air flow problem and I think I just found my video that is my problem thank you so much if anybody else can help me out great thank you I will post a video if you want me to my starting and stopping actually maybe I'll post it anyways

@mice1m1 3 года назад

Worked for me. Thankyou.

@GerardBurkeBurkesGarage 3 года назад

Nice one 👏👏👌👌

@mack1609 4 года назад

Great tip

@GerardBurkeBurkesGarage 4 года назад

Thanks Mack 👍

@JoeBole Год назад

Thank you so much for the information, My toyota surf 1kz has the same issues like yours, engine starts then cuts out immediately. please sir, tell me how can I do to starts the surf.

@anverlouw5694 2 года назад

Thanks Gerard, this is most definitely very helpful and useful information

@GerardBurkeBurkesGarage 2 года назад

Thank you 🙏

@paulmina9429 9 месяцев назад

You are the man!!!!!man appreciated

@mando4025 7 месяцев назад

Thank you Sir!

@vanentseke4069 Год назад

Having same issue on my 05 highlander

@lasers33 Год назад

If you unplug the mass air flow sensor the car will start. If you try to plug it in while it's running the car will die.

@JO-vf8ql Год назад

Will try this next time my engine won't start, thanks

@stevenandcaroletiesi1211 4 года назад

I just started learning and working on my cars at home, would you recommend buying a scanner Home DIY?

@GerardBurkeBurkesGarage 4 года назад

Absolutely, check out my last uploaded video about the scan tool I use in this video 👌👍 A great option that covers so much 😃💪👌

@GaryReviewsStuff Год назад

really helpful gerard would love you to solve my issue as its a ford focus 1.8 zetec s model and star/stop button, heres the issue its start fine and drives and couple meters down road at junction when put clutch in to go from any gear down to like 1st gear it dies and i have to constantly keep putting clutch in again push start button for it to get a little more down raod or any junctions to cut off on me randomly, very frustrating as looked at all types videos and yours seems be closest cause yet but would be intresting if i can get a video to show you :D

@Bachpham132 2 года назад

Thank you very much. You save my time

@nicksonnyabote6174 Год назад

Great video you saved me brother

@paulataya1918 Год назад

Disconnected MAF sensor but no difference. Engine fires up then rapidly dies.

@leonbergman4998 Год назад

This video was very helpful 👍

@paulinocantu8261 8 месяцев назад

Very helpfully, thank you

@mrmralloa8540 11 месяцев назад

Thank you worked a treat 👌

@cjssurf 3 года назад

This happend to my Skoda after the battery died, we jump started it and it kept cutting out, local mechanic tried to as booster pack and the same., got towed to Limerick main dealer, while I was talking to the manager about it a mechanic "moved" the car, aka he has good booster pack. Turnes out the ECU and fuel pump is sensitve to low voltage. Ars 250 euro for the tow. The main dealer didn't charge to clear the ECU fault code.

@sampsonpaintsil9839 7 месяцев назад

Thank you so much ❤

@connieblackmon3932 2 года назад

Well I saw you say try this but I didn't understand what to try.

@iankelly2110 4 года назад

Experience their well done Gerard. Did u get 2 check any live data

@GerardBurkeBurkesGarage 4 года назад

Cheers Ian, 🙏🙏 Yes I was looking at it before and after. When disconnected the air temp went to - 40ish and the MAF reading stayed at 0.35 g/s when conneted or disconnected. When replaced the g/s went to normal expected levels at idle and when reving 👌👍

@iankelly2110 4 года назад

@@GerardBurkeBurkesGarage i will let you away with that one so Gerard 🤣🤣🤣

@GerardBurkeBurkesGarage 4 года назад

😂😂👍

@frankxuereb5422 2 года назад

Thank you so much my friend cheers worked like a charm

@GerardBurkeBurkesGarage 2 года назад

Cheers Frank 🙏

@anasawad8420 2 года назад

thank you for sharing this🙌 i have the same problem Toyota Corolla 09 1.8, i brought a technician to where it's stopped and told me some computer components need to be fixed ( replacing some ICs or transistor) or replacing the whole PCM cause he tried my computer on another vehicle same model and the problem still exists starts then cuts out immediately! what do you think

@beaches2mountains230 Год назад

I've been dealing with this problem today.😢 had it happen about a year ago after throwing a bunch of parts at it...looks like I'm going to have to do it again. Unfortunately this trick doesn't work for my car. It starts up and dies with or without the MAF connected.

@gilbertgarcia4042 2 года назад

Great job, it fixed my problem. Thanks.

@GerardBurkeBurkesGarage 2 года назад

Fantastic 💯👌👍

@crissgen 5 месяцев назад

Thanks for the video, my matrix 2009 when I start stay on a second , what could be the problem , thanks

@patkelly7999 4 года назад

Great tip once again Gerard, did not know that, Thankyou:):)

@GerardBurkeBurkesGarage 4 года назад

One for the filing cabinet Pat 😉💪 Impossible to know them all, we all learn information from somewhere. I have a nice little tip video coming next 😉👍 I learnt it from watching some YT repair videos years ago but no classroom passed it on 👌 Thanks for watching Pat

@patkelly7999 4 года назад

@@GerardBurkeBurkesGarage 👍👍🙏🙂

@closertothetruth9209 4 года назад

I've heard vdo has a high failure rate, it was once top notch

@GerardBurkeBurkesGarage 4 года назад

Not sure to be honest mate, I know the new part has a 2 year warranty for the customer so she is covered in that sense 👌 Poor quality batches definitely happen though, we see it over and over again on all makes and models with certain sensors failing

@vicferrarisgarage Год назад

Amazing. That was it. Thanks 😅

@luiszorto1222 2 года назад

hi thank you for sharing this vd my 08 avalon i same similar but starterd after 3 time and driving good you know what hapen for mu avalon yesterday is the first day with this problem

@thecargotsold Год назад

Thank you. It worked. 🙏

@GerardBurkeBurkesGarage Год назад

👌🙌

@125sm3 4 года назад

Nice and simple fix 👍

@GerardBurkeBurkesGarage 4 года назад

👌👌🙏🙏👍

@marcusreddy6296 Год назад

I have a Toyota etios 2013 same problem auto electrician says a diagonostic checks needs the be done via a Machine.

@steveroche2524 3 года назад

Got a ve lt35 van doin this sporadically I'll try this later

@jj-tt6gl 2 года назад

Thank you so very much..

@pedrojimenez5508 2 года назад

Hey man great video. I had this issue and changed the maf sensor and it worked great. A few weeks later and it just did the same thing to me again. Any tips?

@stevofromiowa 2 года назад

Might be wiring...or a faulty sensor.

@stevofromiowa 2 года назад

Some of the aftermarket parts quality is poor anymore.

@josephhinton5489 2 года назад

you didn't really explain where to find the mass air flow sensor because where you found it on your demonstration vehicle is where my my master break cylinder reservoir is located.