Step Up Your Box-Making Game! | Four-Corner Grain Match

Подписаться 865 тыс.

Просмотров 261 тыс.

50% 1

Watch our latest video! "Refinishing a Retro Heywood Wakefield Desk With A Stunning New Look!"
• Transforming A Retro H... -~-
One of the tricks woodworkers employ to make keepsake boxes look their best is to cut the box sides from a single board. If you keep the pieces in order, you can achieve a nice grain wrap around three corners. Unfortunately, the fourth corner will always be a mismatch. There is a way to get a nearly perfect four-corner match, if the material will allow for it. What I mean by that is the board needs to be thick enough to sustain a resaw down the center. In the case of this particular project, I had a board that was a full 1" thick and after resawing I was able to easily get the desired 3/8" thickness for my box sides.
To make a four-corner grain match, it all starts with careful layout. Draw a center line down the length of the board and then measure and mark the cross-cuts that will make up the box sides. The layout and cutting process is shown in the video and feel free to pause as needed to get the info you need. You'll have to forgive me for not writing out every step as this operation is incredibly difficult to describe. So watch the video.
In the end, you should have four grain matched corners. They may not be 100% perfect but they'll be close enough to serve their purpose. And even experienced woodworkers will look at the box and wonder how you did it. So step up your box-making game and give a four-corner grain match a try!
Relevant Links:
+ Essential Joinery Book - thewoodwhisperer.com/product/...
+ Merle Band Clamps - amzn.to/3Cz4W8d
+ Blue Shop Towels - amzn.to/3vQXemc
+ Bumblechutes Wood Finish (Save 10% with TWW10)- www.bumblechutes.com/product-...
Join this channel to get access to perks:
/ @woodwhisperer
Sign up for our free newsletter to be notified of a new video or other cool stuff happening at The Wood Whisperer! thewoodwhisperer.com/newsletter/
Check out our new short-form videos on Facebook! / thewoodwhisperer
For more information, free plans, and helpful links:
SUBSCRIBE!
ru-vid.com_c...
Take a woodworking class online with The Wood Whisperer
thewoodwhispererguild.com
SUPPORT US ON PATREON!
/ woodwhisperer
PRODUCTS RECOMMENDED BY MARC
US - www.amazon.com/shop/thewoodwh...
Canada - www.amazon.ca/shop/thewoodwhi...
UK - www.amazon.co.uk/shop/thewood...
CHECK OUT OUR BBQ CHANNEL
/ twwbbq
WOOD WHISPERER en Español
/ wood whisperer en español
CHECK OUT OUR SHOP TOURS
www.thewoodwhisperer.com/shop-...
GET INSPIRED BY OUR VIEWER PROJECT LIBRARY
www.thewoodwhisperer.com/viewe...
DOWNLOAD OUR FREE APP
iOS: bit.ly/177u4An
Follow me on:
TWITTER - / woodwhisperer
FACEBOOK - / thewoodwhisperer
INSTAGRAM - / woodwhisperer
Pinterest: / woodwhisperer

Хобби

Опубликовано:

8 янв 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 215

@woodwhisperer Год назад

Relevant Links: + Essential Joinery Book - thewoodwhisperer.com/product/essential-joinery-book/ + Merle Band Clamps - amzn.to/3Cz4W8d + Blue Shop Towels - amzn.to/3vQXemc + Bumblechutes Wood Finish (Save 10% with TWW10)- www.bumblechutes.com/product-page/furniture-finish?ref=tww

@roj487 Год назад

I've been a woodworker for just over 60 years now. I owned a custom woodworking shop for years and now have a beautiful home shop with all the fixings where I get to spend many stree-free hours with no dead lines. If today's technology to share knowledge had been available back when I started out I can only imagine where I'd be today as a woodworker. To be sure, there were masters of the craft that we could seek out and study under but we seldom had access to them and usually at a hefty price. So today I teach free of charge (except for supplies) those who are or want to be workworkers and are willing to put up with the old guy in the shop who thinks he owns the place. It's my way of giving back and passing it on. I really hope people today appreciate what you and some other excellent instructors are sharing free of charge online. I know that our craft will continue and grow because of your efforts and others like you. I can only imagine where woodworking will be in 30 years with great teachers who are knowledgeable , entertaining and inspiring. I wont be around at that time to see how it all turns out but I'm sure you and a few others will be able to look back on the evolution with great pride. This was my long winded way of saying thank you to you Marc and others who are also doing an amazing job. Just a Chip Off the Old Block But what A Great Block it Was Cheers

@mattheww7280 Год назад

Great Video Marc, wondering where you got the green sanding block from? Lee Valley has a similar red one but maybe slightly larger

@johnnation713 Год назад

Wow, that’s really incredible Ro-J. I can only imagine where I’ll be in 60+ years of woodworking!😱 I really appreciate your comment and your thank you to Marc, I too owe him a huge thank you. Marc wasn’t the one that got me started I did that on my owe learning from my mentor named Scott Robeson and he was great to learn from, very wise and extremely knowledgeable when it came to woodworking. Surprisingly enough he sought me out because of my work ethic at a local grocery store, I was a meat cutter for 15 years and it paid pretty well, however when I started working for Scott I got hooked like crazy! I started working for him part time after I managed the meat department at the grocery store back in 2017, so that was when I started it all. I’ve been woodworking for 5 going on 6 years now, I do t work for Scott anymore. I started saving all my extra money that I could get my hands on and started buying equipment and watching Marc sometime around 2018, Marc had already moved to Denver by this time, but I watched all of his older videos and I learned so much from Marc and I have a shop of my own now, not all the equipment but most everything any woodworker could start out and I have started my own business and so far so good. I finally left meat cutting for good this last spring in May but I still don’t make enough to do it alone so I started working at my own town’s water treatment plant and I just past my level 1 water operator test and I’m on my way to helping my town. I love woodworking and I watch all Marc’s new content when I have time, he’s so knowledgeable and I respect what and who he is. I read your response Ro-J and it reminded me of my journey and I just wanted one the most respected people I know to know my story and you as well Ro-J. Thanks guys, much respect and thank you for your time😊👍

@keithbrock6410 Год назад

In a time when every other woodworker channel seems to be a sham wow commercial for the 5 tools under $20, you are still putting out great content on builds. Thanks man, and that turned out beautiful, and great instruction also.

@DaveYoakum Год назад

Right? Woodworking RU-vid isn't what it used to be just a year ago. I'd blame TikTok, but there isn't long form video content there. What's going on?

@xXSCARECROW19Xx Год назад

Yeah seems like there's only a handful that do build videos anymore. Tww, stumpy nubs, Tamar, and a few more. I honestly like to learn about tools but I prefer to learn about them in use in a build video.

@peterfitzpatrick7032 Год назад

... or installing mega machines and losing touch with the viewers... yeah, I'm lookin at you Malecki !! 🙄😂

@AusWorkshop 5 месяцев назад

@@DaveYoakum Greed

@ddutton0 Год назад

The quickest I have ever been in viewing one of these

@OldDocThedan Год назад

Good lord. How many box videos have I watched? Way too many, given that I rarely learn much new. But that little moosh of a bad edge really ties the room together. Thank you.

@mikehill3426 Год назад

One additional technique is to start with a board wide enough to get the top and front to grain wrap. I call it the 5 corner match.

@ScottHaun Год назад

my grandmother asked me Saturday to make her urn so the timing is impeccable.

@subgeeze 2 месяца назад

I guess with an urn you don't often open it up to check on the inhabitant, but I kept waiting to see what you did for a handle. Very nice! I will use the 4-corner-match trick.

@joshualloyd2915 Год назад

I was confused at first then...suddenly...it clicked. Thank you!

@RobinLewisMakes Год назад

The screwdriver on the corner trick got me all excited!

@roelultriplo 6 месяцев назад

Nice to see a carpenter with 10 fingers still!

@StefanoBorini Год назад

This man makes a simple box into a piece of art.

@steenfraosterbro3268 Год назад

I have to come clean and let you know I kept this video in my wood working folder.

@ThePerpetualStudent Год назад

My dad died in April, I am going to try and make this box for me mom.

@JimHester Год назад

Three things to note here: 1. I received a copy of the world-renowned Essential Joinery for Christmas, and it's awesome. 2. You are the only other person I know who owns a Craftsman Guide Master™ push shoe. 3. Beautiful project!

@jaydenhouseman9484 Год назад

I discovered this push stick in a box of hand-me-downs. I like it. Mine is Orange.

@waukeecabinetworks5690 Год назад

45.5 Degree miters are a huge help when assembling miterfolds!

@marciomarcelli9106 13 дней назад

Detalhes fazem a diferença. Ficou muito bonita! Comprei o livro pela Amazon pois estou no Brasil! :) obrigado pelo vídeo, foi muito didático!

@Mikey__R Год назад

I've seen a lot of hard wax finishes in RU-vid land recently. In fact, I think this is the first tung oil finish I've seen for a while: I'm glad the classic is still relevant!

@BIGREDDOG09 2 месяца назад

nice box bro

@GlassImpressions Год назад

I love your humor. My wife would say identical to my immature self! 😂

@taylorsand Год назад

Nice work Mark!

@jimrosson6702 Год назад

Looks amazing glad to see you making stuff again

@meatwhisperer Год назад

As always, great instructional content!!

@christ9359 Год назад

Marc has a masterful eye, which I think is what sets him apart. Yes, he has the skills, but he makes beautiful pieces of furniture, because he has an uncanny eye for making the grain work within his pieces.

@jakedevillier5863 Год назад

Well, that and he has all those fancy tools. I could make that too if I just had all his fancy tools !

@lifter78 Год назад

That looks amazing

@paulfowler3416 Год назад

Excellent talk through and demo, thank you.

@frogsoda Год назад

This is how I've always made boxes.

@tilmanbauer5728 Год назад

It you cross-cut the pieces on the table saw, with the blade at 45 and just high enough to score the top, you can avoid that 3mm gap between the faces altogether.

@davecurda2350 Год назад

Good video Marc

@nevadacool Год назад

Thought it was just another box video, but love the tips on resawing, and the tonge oil. Nice work

@AusWorkshop 5 месяцев назад

I've been doing them that way for years but it's good to see it explained so well.

@richlew9385 3 месяца назад

You’re a dang beast dude!!!! 💥

@PainlessChiropractor Год назад

Clear, accurate build video, and beautiful box.

@gbjones54 Год назад

I’d never seen this before Marc. Thank you.

@justplanebob105 Год назад

Thanks Marc! I love making boxes and I really appreciate when your videos help improve my skills.

@1954JDR Год назад

Wow, that was so easy. Beautiful box.

@scottroy6195 Год назад

I would be caught dead in that box! 😁

@tektrixter Год назад

Great technique! Adding it to my collection.

@jeffreysmith5018 Год назад

Very nice! I love the look of that finish. I’ll give it a try 😀

@-11BRAVO- Год назад

Beautiful box

@jlbfd9389 Год назад

That planer is sweeet!

@joshsandler3122 Год назад

literally started building a box today - good timing, and thanks!

@sehabets 9 месяцев назад

Finally tried this process, work like a charm, thanks for the great video.

@MCsCreations Год назад

Beautiful, Marc! Really amazing work! 😃 Thanks for all the tips!!! Stay safe there with your family! 🖖😊

@johnmooney9016 Год назад

Super clean video, nice editing! Love that nice little planer...

@beardedgarage Год назад

I came here to see the tricks and appreciated the fact you were using a graphgear 1000 while marking boards. Nice work.

@matthysloedolff Год назад

I remember you posting a short version of this to Instagram and at the time I was a bit confused. This video cleared up my confusion and I think this is quite possibly the most satisfying trick one can use for making a fancy box. Thanks, Marc!

@stevendavis6759 Год назад

Great video fantastic skills thanks for sharing!!!

@jeremyspecce Год назад

After you posted this on Instagram I tried it on both a small tool box (box jointed) and a tissue box holder (mitered) . My biggest issue was what you warned about; I took too much material out in my resaw because my bandsaw was drifting and it required some extensive jointing to get it flat, so the grain is not perfect but it still flows pretty nicely. I’m going to make sure my bandsaw is all Snodgrassed up next time.

@garynicoletti7182 Год назад

Great build and love that the grain is gorgeous all around. I also see that you added a sacrificial fence to the Woodhaven 4448 Ultra Track you attached to the SawStop fence.. Nice touch

@charleselkins4546 Год назад

You are quite the craftsman. Good luck in your new shop.

@davidmeyer9204 Год назад

Thanks Marc!

@jonathanmiddleton5261 Год назад

Thank you man. I still believe it’s magic how you get it to work and I’m really digging the new shop.

@johngrubbs9494 Год назад

Thanks Marc! I picked up a number of good techniques from your excellent video(s). I'm embarking (pun intended) on some box making soon and will use some of your tips.

@EvanDunville Год назад

Good Looking box. Ill have to save this video to remember how to lay out the cuts!

@johnnichols8553 2 месяца назад

I'd like to see a video on how that spline jig was made. It looks simple enough, but I can screw up anything.

@sgsax Год назад

Don't know why this never occurred to me, but it's brilliant. I really need to improve my resaw capability... Thanks for sharing!

@andrewbrown8148 Год назад

That's a beauty, Marc~! I had a friend ask me about making an urn. I was a bit intimidated by the request until I learned that it was for a pet. Thanks for the inspiration~!

@johnnyb95678 Год назад

Thank you Marc. I really appreciate your approach and focus on detail.

@woodwhisperer Год назад

Glad it was helpful!

@mattheww7280 Год назад

Never would think to cut the bevels on a Miter Saw vs the Table saw. Interesting. I have a non sliding Dewalt DW715 and happy with its accuracy (I know you had it for a short time =-), just never would think of doing it this way. Thanks for opening up another option for a future application.

@Kosh42EFG Год назад

Smooth shaft. Fnar!

@motrebal Год назад

Great video, you are so much more relaxed than you were a few years ago and it makes for a better viewing

@112doc 7 месяцев назад

I use splines all the time for small boxes, made of contrasting wood. They are very strong. Good job!

@eikestrumpelmeyer Год назад

Very nice work 🤘🤘👍

@markhicks8377 Год назад

every time i hear a festool start up it sounds like the bearings are bad

@melodywilson5255 Год назад

looks Prittay Prittay Prittay good! Hahaha! I do love this though!

@brenthiggins6253 6 месяцев назад

Very nice, thank you.

@missamo80 Год назад

Perfect timing for this video, I just picked up two offcuts of walnut from my local candy store to try making my first box!

@jerrymcdonald6445 Год назад

Great video, thanks for sharing. I just purchased your book on Amazon.

@patriciamay638 Год назад

Thank you. An excellent video covering off the skill and detail necessary to produce a beautiful box. Woodworking is joints and grain, and this basic project reinforced the principles which can then be reapplied to other projects.

@leiwa100 Год назад

Nice video. I learned that you should flip the board so that the outside is on the inside. Thank you

@prilep5 8 месяцев назад

Amazing

@andrhamm Год назад

Nice! I've seen a bunch of these box videos lately, which is great because I've been accumulating hardwood offcuts and plan to make some boxes, but the missing video is taking a box like this to the next level and adding trays and compartments for storing and organizing things. Something smaller than a toolbox with a hinged lid and some kind of locking hardware would be great... and maybe some Kumiko... get Mr. Farrington on the horn! Don't forget flocking! 😄

@Mark_Wood Год назад

That's really cool

@Mburrisnav Год назад

I was so surprised when I figured this grain wrap trick myself without seeing it from anywhere back when I made the dice towers.

@malcolmsmith5903 Год назад

Nice job. Well presented. Love it. If you leave the board a bit wider then if the grain does shift after smoothing the saw marks then often just moving boards up/down a bit can catch it again then recut to final width. Board selection helps for grain wrap. Nice to see a shoulder plane in action - router plane works too.

@peterfitzpatrick7032 Год назад

If you are putting a tray in the box, you can cut the splines deeper so that they show inside... (I know you already know this Mr. Whisperer) 😎👍☘️🍺

@dinacusic7829 Год назад

I made a recipe box similar to this for my sister for Christmas and the wrapping grain is just 👌 I referenced the Jonathan Katz Moses video but this would've been even better to know about

@johnlp3376 Год назад

I'm building a end table now not a box but I resawed my legs and my top ( table saw saving for bandsaw ) using walnut so expensive trying to save yet make look good as much as I can. This is a great video and explanation of how to figure and match grain like I'm trying to do now ( on every project understand it's a box but ya know ) still apply to a lot of projects. Thanks now I'm show the wife how bandsaw saved material lol thinner kerf lol hey worth a shot. Great video and learned a lot.

@franklange7692 11 месяцев назад

Smooth shaft ,,I get it😅....great video .Thank you for sharing

@de3be 9 месяцев назад

That's a great video! I use something similar when making my frames. It's not as continuous since the visible part of the frame is mitred, but yields better results than cutting it from a straight board.

@vbacans Год назад

Excellent video and instruction. These type of details are what sets woodworkers apart. Timing couldn't be better because this is my next task going forward.

@rodrigoreitz7699 Год назад

Belíssimo trabalho. Parabéns! (Beautiful work. Congratulations!)

@thomaslbryant 10 месяцев назад

My friend, I bought one of those expensive wall ornaments my first week of owning a saw stop! Haha! Now I never run reclaimed wood without bypass mode.

@J2ricker 4 месяца назад

Awesome box! Cant believe i hadnt seen this video. Being off for the holidays hurt my pay situation a good bit maybe in a couple weeks i can het a heater for thr shop and go make some stuff. Spring will be here soon now and ill be building me an above ground shop. I think ill go with 16x16.

@michaelpatrick6950 Год назад

I just made a box like this between the holidays. I also hate bevel joints, so I rough cut on my miter saw and clean them up with an Infinity Tools Mega Chamfer router bit.

@0xJaymes Год назад

This one time... using band clamps... Seriously though, for the top band clamp you don't need a second person, just set it on top of the bottom one, get it adjusted & you can work the individual corner clamps into place before tightening.

@TheOldBlackCrow Год назад

I've been working on a humidor for a retired colleague... Your video makes me want to start over, but Spanish cedar is too expensive now. But definitely excellent info for future projects! Thanks!

@runifuceeme406 8 месяцев назад

@9:59 DEFINITELY TRIED YOUR SMOOTH SHAFT ADVICE.. THEN THE WIFE CAUGHT ME... NEEDLESS TO SAY, I HAD A LOT TO EXPLAIN, AND WAS SLEEPING ON THE COUCH THAT NIGHT..

@magicworldbyjorg Год назад

,a cool video keep up the great content.. Thank you……

@bfirefighter3 5 месяцев назад

Chisel across index finger knuckle. Cut through all the tendons into the joint capsule. 2 surgeries and 6 months of rehabs later and I’m at 75 percent function.

@isaacbrooks5999 Год назад

This is great! My boxes always end up with that one corner that doesn't flow. Now I need to get a bandsaw💸

@adamdejesus4017 Год назад

If you lack a band clamp, try connecting cable ties/zip ties together. Not reusable but provides lots of clamping power. I've made a lot of splined boxes just like this, except never with the 4-side continuity. My kingdom for a bandsaw.

@inmybox2023 Год назад

This is a really cool method, I just started experimenting in making smaller boxes, I will be able to get a full wrap on a 7" x 5" box from a 24” long board which is never 24”, only have a table saw, think it will still work with a 2.6 mm kerf

@PaulMorley1 Год назад

Mental note. Be careful when taking a sip of hot coffee while watching wood whisperer videos. cough cough (9:56). 🙂

@johnnation713 Год назад

I’ve been trying to do the same thing, I did a birch waterfall cabinet for my uncle and it looks wonderful, the very last corner of course didn’t look as cool as the other three, however it’s underneath the cabinet so you’ll never see it.😊👍 Thank you for actually showing me this for first time and now when I do it I try to do the exact same thing you’re describing right now. Thanks so much Marc, you’re the best😊👍🤘😝

@woodwhisperer Год назад

You can do it!

@antennasbc Год назад

Thanks for the great video! Did you glue the bottom all the way around? Is there any worry about the bottom expanding? Im pretty new to woodworking ,.that's why I ask. Thanks again!

@AusWorkshop 5 месяцев назад

Yes I would be worried about this box in humid conditions. I never make a box with a drop in lid like that. It's asking for trouble in my opinion. In fact I'm surprised Marc did it that way. Wood movement is so often ignored these days. I always do my lids to allow for movement. Wood never stops moving no matter how dry or old it is or how much finish is applied.

@rolandgdean Год назад

I've been making and selling boxes like this for years now on my Etsy store. I always re-saw and grain match all four corners when possible. Quarter-sawn grain works pretty good as well if the grain is all very straight lines anyway...like Sapele of Padauk. I think it's an amazing bit of detail HOWEVER, I've never had a Customer mention that specific detail in any of the CX reviews I've gotten...disappointing really but it is what it is I suppose...it's worth it to me though knowing it's masterfully done.

@joshbrossart4898 Год назад

On a small box like that do you not glue the bottom for wood movement and if that's the case do you undersize it just a little bit

@billhickman6455 Год назад

As usual great work, detail and inspiration. Just curious why no lid handle?

@CordellWoodworks Год назад

My father in law passed away a few days ago and I had started looking at urn builds yesterday because I wanted to try and build his. What a well-timed video with great information. I for sure would have screwed this up. I have some beautiful curly maple that I would love to use but I think I would like to stain the top a darker shade. Any recommendations for staining maple subtly dark (somewhere in the middle between maple and walnut lol).