Stihl Br600 How to Set Valves DIY

Подписаться 57 тыс.

Просмотров 44 тыс.

50% 1

How to set valves on your Stihl BR600 this process is very simple make sure your on the compression stroke and line the flywheel tip with the edge of the coil like shown in the video. remove the top cover and insert your special feeler gauge that you can get from Stihl for like 3 bucks. set it so that the feeler gauge has a slight drag and your set set for another 100 hours
Cameras used in My videos
Sony Hx80 amzn.to/2kUTNaF
Olympus TG-Tracker amzn.to/2dYKLZr
Sony A6000 amzn.to/1ROrgJl
TG-860 amzn.to/1VU6vzP
DJI Osmo amzn.to/1QDjGFb
Drift Hd Ghost amzn.to/1UUiZZU
SJ4000 amzn.to/2bel0jt
Vidi Action Camera amzn.to/1SaLBtu
Sound effects by Epidemic Sound
epidemicsound.com
Royalty-free music by Epidemic Sound
epidemicsound.com

Авто/Мото

Опубликовано:

15 фев 2017

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 58

@curtisbaker5407 Год назад

What size feeler gauge did you use?

@joshuabowkley3490 Год назад

I need to know this as well. The thickness of it for the br 600. Lol, I'm too cheap to buy one for .70 cents Joking, I need to know before mine ships to use a sparkplug gapper now. Or I'll have to clean out these gutters by hand ..

@jerrydchambers2834 Год назад

What is the thickness of your special gauge,. 00.8 ???

@SteveRobReviews 7 лет назад

My new stihl brushcutter is regular 2 stroke. My friend bought the 4 mix motor and it is quieter tons of torque , less vibration and burns way less fuel than mine. I didn't want to buy the 4mix engine with the valves but it turns out it's a great system. We use ours a lot , last year he burnt 25 litres thru the 4 mix engine making bush trails and he hasn't touched the valves yet.

@TestDontguess 7 лет назад

ya you need to keep up on the maintenance on those engines or they shit the bed

@luisreyes3162 6 лет назад

Thank you , you explained more clear, I was a little confused but now I know.

@mattavalon 7 лет назад

The best video out there! Thanks

@99carnot 7 лет назад

Nice tutorial. I think the valve cover screw is a T-27.

@brianmorriscey3010 5 лет назад

T-25

@ryerob741 5 лет назад

They are t27 no doubt about it, t25 will seem to fit but you will strip the torx head

@crankshaft1053 5 лет назад

Its t 27 made the mistake had to drill out some bolts

@joshuabowkley3490 Год назад

It is a t - 27 fellas.

@ramonpiqueras5812 6 лет назад

Thank you very much.

@isidroizazaga2786 5 лет назад

Good video

@mikespain8655 6 лет назад

Need to buy a valve kit from Stihl parts supplier. It has a tapered feeler gauge (.06 I think) gasket and washer. Otherwise you have to cut down your existing feeler gauge to make it fit. Good video man.

@TestDontguess 6 лет назад

+Mike Spain the feeler gauge from the dealer is only like a couple dollars

@ryerob741 5 лет назад

You will notice dude may several misquoted, the screws are T27 torx, and he said take the valve cover screw and bolt down cover, well theres a crush washer needed rite there also, and never reuse cork gaskets

@douglaslaramie9245 7 лет назад

Do you need a special tool or will a typical feeler gauge work to set them valves. Your good at this stuff Jerry. Wish you was my neighbor. Guess I'll have to move to Alberta because I don't think you would ever come to Ontario. HaHaHa Thanks for posting. KIT d

@TestDontguess 7 лет назад

for the couple bucks it's worth it's best to buy the tool, if you have feeler gauges you can try to cut it but then you risk the chance of not getting the proper fitment

@mab123080 3 года назад

What would cause a push rod to drop? I literally was checking mine & while valve cover was off, turning flywheel to TDC I saw the intake side push rod fall down. Now it won’t move more than a half turn either way. It’s not at TDC either. Could that be a timing cam gear or what else am I over looking ? Could that mean the valves were too loose before I checked & the rocker arm jumped off push rod ?? I suppose there is hope since this happened while engine wasn’t running?

@joshuabowkley3490 Год назад

Sound like your cam broke buddy. That or your push rod.

@joshuabowkley3490 Год назад

To be more clear it shouldn't fall into the jug unless something is broken or removed.

@georgemarkle1079 3 года назад

With the spark plug in the pull cord is hard to pull, with spark plug out pulls easy, could this be the valves out of adjustment??

@snoopfurlow1275 2 года назад

No.adjust your values at .10 with the piston up..because you gotta run them 50.1 .and if it dont work pour a little mixing oil down the spark plug hole and lubricate the piston.wait 5 minutes and then pull it

@jameskallas388 3 года назад

I have a BR600 in my shop, timing and valves are set to spec, but, when I trey starting the motor, I can't pull it over, it pulls the starter handle right out of my hand. I'm getting frustrated, I checked and double checked and can't figure it out.

@snoopfurlow1275 2 года назад

Pour some mixing oil down the spark plug hole and that will lubricate the piston.the piston walls may be dry.the oil will help free it

@thatdudemoe9109 4 года назад

Would a bad adjustment cause a rough pull rope?

@evictioncarpentry2628 3 года назад

Yes. It won't decompress like it's supposed to when pulling over.

@joshuabowkley3490 Год назад

You got that right. It made me break my pull cord, and snap the plastic peices that catch the crank shaft in that assembly. Lol. Deff adjust those it's very simple with the correct tools.

@thersten 5 лет назад

what's size is the feeler gauge you're using?

@TestDontguess 5 лет назад

Custom feeler gauge from the dealer

@thersten 5 лет назад

@@TestDontguess thanks for the reply. Just found out some folks say between .004 - .006 inches

@ryerob741 5 лет назад

@@thersten there is a valve maintenance kit that still sells, it has replacement gaskets and the correct valve lash gauge included for just a few bucks

@trevorcalhoun8591 7 лет назад

what is the valve clearance gap?

@anthonyfoster7206 6 лет назад

Trevor Calhoun 004/1.2 mm I think but please check with stihl

@robertcarpenter3256 4 года назад

@@anthonyfoster7206 WOW 1.2 mm is .047 lots of difference there.

@tokslut 6 лет назад

Didn't you se all the metal shavings you left after the 8mm tool on the rocker :O

@TestDontguess 6 лет назад

It adds horsepower lol

@barqzrdavi 7 лет назад

pretty much ALL machine screws are T27 ,,,,,,, just saying

@stewiegriffin6503 7 лет назад

2:00 are those weights ? Jerryyyyyyyyyyy ! I didn't know you do bodybuilding ?

@meanjoegreen4925 7 лет назад

LMAO, 1/8 of a lb

@anthonybush3134 5 лет назад

I didn’t use a gauge. I just turned it a little at a time until it was earlier to turn the crank.

@jaimecornejo2185 2 года назад

I have adjusted valves multiple times at tdc and one valbe specifically the one on the left keeps popping out of place when i turn on the br600 within about a minute of full throttle what am i doing wrong?

@TestDontguess 2 года назад

Possible bent or damaged push rod

@joshuabowkley3490 Год назад

It is damaged.