No video :(

Stop Wasting Tumblers - Tips And Tricks To Successful Rotary Engraving

Подписаться 20 тыс.

Просмотров 11 тыс.

50% 1

#rotoboss #engravingtumblers #laserengraving
I have wasted a ton of tumblers and water bottles with silly mistakes and the cost adds up! In this video, I'm sharing my top tips and tricks to help you be successful when using a rotary for engraving, but also lasering in general.
Laser Engraving Checklist: addicted2diy.c...
130W Rotary Engraving Settings: addicted2diy.c...
Rotary Settings Test Card (download the file and then open in LightBurn): drive.google.c...
Aluminum Tape (affiliate link): amzn.to/3RqcfDR
Masking Tape (affiliate link): amzn.to/3LUXJTo
Beverage coolers to test colors (affiliate link) amzn.to/3dU8uZy

Опубликовано:

5 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@coralwegener6861 3 месяца назад

You're so generous for sharing all this info, especially your settings! Thank you!

@MrBdub16 7 месяцев назад

Thank you so much for your cheat sheet. It was a great place for me to start with my laser. I have the Atomstack X20 Pro 20w diode laser. I created a material test using your data and I was actually able to increase speed and lower power slightly. My best results for names on a Yeti were 740-28-450.

@addicted2diy 7 месяцев назад

Awesome! So glad to his was able to help you!

@wesbiehn4443 Год назад

Lots of helpful tips here! Especially for this rotary newbie! I just found your channel here recently and am literally watching every one of your videos. Keep it up!

@allenyarberry7502 Год назад

Thank you for the pointers. I watched both of your tumbler videos. WELL DONE!!!!

@boerieroll5453 Год назад

Your videos are very helpful - thank you for taking the time to do these - greatly appreciate it!

@robr9521 11 месяцев назад

One tip about your mention of homing causing collisions.... There are settings in Lightburn under Machine Settings/Vendor settings to allow you to turn off X and Y homing if you are using your rotary a lot and leaving it on the table.

@addicted2diy 11 месяцев назад

Thanks! I will look for that!

@TheGardeningCoach Год назад

Awesome information. I am new to the Thunder world. I have a 51/130 too. Thank you!

@bginn3448 Год назад

Thanks Katie!

@TheJourneySoFar1966 6 месяцев назад

Thank You!

@keelyrommel7445 7 месяцев назад

Great video! Do you have any tips for avoiding the smoke staining that can be seen on light colours like white?

@steinbierz Год назад

Thanks for providing your chart! I just received a Nova 63-130 so this is very timely. On your chart, are the three or more different settings for each color the "range" you spoke of, and, if so, are they somewhat in order of most used setting to least used? Thanks.

@chucksukiasian8159 Год назад

Hi Katie, I followed the cup link, however, I cant seem to find a way to order 16 individuale colors. Each color comes in (6) pieces at $70. That would come to $1120. Pretty steep for testing. Am I missing something on the order page?

@MichaelMcGuigan Год назад

When you mentioned that the steps per rotation was off due to a Lightburn update, did the number itself change in the settings or the the setting needed to be changed? For example your normal SPR for a 32oz tumbler is 5000 and when you checked it was at 5500 or was it still at 5000 and just didn't work anymore.

@addicted2diy Год назад

My settings in lightburn did not change. So per your example, 5000 stayed 5000. But those settings were then off when I sent the file to the laser. I had to do some testing to then figure out what the new number would be for the steps per rotation. Now, every time I get an update, I make a note to confirm whether the SPR changed. It doesn’t happen to everyone, and I don’t know if it was just Mac users or if it was just a random event for some.

@MichaelMcGuigan Год назад

@@addicted2diy thanks for the clarification. I'll add that to the checklist.

@bginn3448 Год назад

Where do you buy your tumblers? Thanks