but one fine day, the true welders of this country decided to return. I tucked my tail between my legs and went to the airport, but there were no tickets and I had to leave the country with the landing gear of the plane down
I actually knew someone when I was in the Navy that was a Nuclear welder, and was sent to Iraq to uparmor HMMWV's and he got to hand pick his team of welders, about as close to a Navy Seal welder I could think of.
As a professional Mexican since 1979, I can honestly say that watching these welders weld while eating tacos de carne asada and al pastor con limon, cebolla and cilantro topped with chunky super spicy red salsa and a cold coke is without a doubt the best way. Provecho
As your assistant I have been welding in those 87 years and you were sitting in the office either reading how to weld or more recently watching RU-vid on how to do it for 87 years.
Un detalle erróneo en lo mostrado , deberá comenzar a soldar desde cada punta de varilla hasta el centro , luego digo : sin separar las piezas solo soldando de ambas caras será suficiente , inseparable , dónde comienzas a soldar acumula material ,dónde terminas la corrida del electrodo socava y en consecuencia debilita ese punto
Я сварщик если вас учат варить арматуру шлите нахрен , а если надо по технологии тогда дадут тех карту и спросят накс это у нас так в России 🇷🇺 все остальное мамкины инженеры 😂
Não tem a mínima penetração, pois estão trabalhando com a amperagem muito baixa, da pra ver pela fissura q ficou no começo da primeira solda, não formou a poça de fusão correta
If they ran it well it would be nice but if not gaps peaks and lots of crap. Though this is the best welding I've seen in you tube shorts as they actually followed some decent steps. They also didn't tack weld the whole thing
As a welder of 15 years, I'd say this is a solid process. I'd run second cap pass, or two stringer beads, as that right side looks like undercut. Then flip it over to get a full pen on the back side.
So what makes the second method that adds some extra space between the parts better than the first? I really don't get it, I would think all it is gonna do is cause you to have to do some more welding?
It's great to finally see a welding video where the "welder" actually runs a bead instead of doing a bunch of spot welds one beside another the length of what they're "welding".
@@SergeySCAГОСТ14098-2014, сварной шов С23-Рэ, зазор между стержнями меньше 0,05 диаметра арматуры, а это может быть и нулевой. Например, для 12 арматуры максимальный зазор 0,6мм, а не как в ролике примерно 3мм.
@@Rammetallist. Металл пролился вовнутрь , все промежутки залил . Автор считает что это прочнее . Хотя как я варю мощность сильнее делаю , электрод не жалею , такой же провар .
@@Rammetallist. Металл пролился вовнутрь , все промежутки залил . Автор считает что это прочнее . Хотя как я варю мощность сильнее делаю , электрод не жалею , такой же провар .
@@edmundooliver7584 in Chile we have earthquake proof houses and skyscrapers, the overlap is just much much longer than in the video without the weld. A 3 storie house have 2 of those bars one going from 1st to 2nd floor and the other from 2nd to 3rd floor, the second floor have double rebar basically so instead of being the weak point is the strongest, welding it would make it britte thus bad for witstanding tremors, it needs to be flexible but indestructible.
@@edmundooliver7584 forgot to mention Japan and Chile work really close in anti earthquake tech since we are the 2 countries that are most affected by them in this planet, as soon as one find a new trick that one tells the other to develop it togetter.
The lesson I take from this video is that no matter what type of weld you do, there will always be a welder who tells you that you're a fucking idiot for doing it.
As a welder with 7931 and a half years, i can tell you this is absolutely the wrong way to weld two pieces of ductile iron together with an aluminum tig welder. That rod should have been a tungstin oxide inner flux core wire feed rod and the parts should have been prewelded in china first. Amateurs smh
Not allowed for concrete rebar... Changes the metal properties! Tensile, elasticity, etc. fine for fencing or farm work or hayseed mechanics. Can't use a torch to tut it either.
@@patrickolson9089it creates a weak point where it's likely to snap so it won't affect the whole bar but where it was heated is likely to snap there is a way of welding rebar together and still using it for concrete without changing the properties all that much but it's honestly just not as cost-effective or safe as just tying it together
@@patrickolson9089 just telling you what my engineers told me on the job in Texas. You heat up more than two or three inches. Hold the bar while your cutting it, if you don't believe me. In every spec on every job I ever did in 45 years.
Only 400 years in the trade? You don't even know you're born. When I was hired to weld Julius Caesar's chair made of rebar this is exactly how we did it.
Я не сварщик, а слесарь. И скажу что сварка арматуры не предусматривает тепловой звзор (чем является то что он сделал якобы правильно). Этот зазор предусмотрен для сваривания труб где будет проходить газ под большим давлением или жидкость так же под давлением. Такие зазоры не дают трубе отклонится (сварщики знают что шов уводит металл на себя).
На ванной сварке арматуры должен быть зазор и запил под углом, зазор делают не только на трубах, на любом толстом металле на котором будет нагрузка. Делают это для того чтобы провар был полноценный, так как не возможно большую толщину проварить в один проход, а то что металл тянет пол беды куда важнее чтобы сварка соответствовала требованиям по нагрузке иначе просто лопнет.
@@user-tm7fu7vo5rна чистую арматуру не может быть нагрузки, она всего лишь часть железобетонной конструкции, поэтому для связки достаточно даже поволоки, а если и использовать сварку, то достаточно прихваток. Никто силовые конструкции из голой арматуры не делает, для этого есть другие виды проката.
На арматуре у тебя и так зазор от рефления...и в нормах нет установки зазора если ты тока не в торец вариш...а провар будит по любому если ты уж совсем не сварщик...
Quality welders are rigorously trained and tested on their skills. None of that matters though for a home welder. This joint would work just fine at home. That being said. This is why welders in the comments are so critical of poor quality weld/welders. The standards they have been trained on live in their minds. This weld started off ok. A gap may not have been necessary. Where it took a turn was when they decided to weave the cap pass. Which caused inclusions in the legs.
Тебя выбесили. А у автора 300к просмотров и тысяча комментов взбешённый правдоискателей. Что конвертируется в звонкую монету. А его кошельку с монетами глубоко наплевать, что в ролике показана бессмыслица или неправда, когда капают монеты!
Зачем делать зазор при сварке арматуры или прутка, ну не будет такой нагрузки чтоб порвало сварочный шов, а если и будет нагрузка, то арматуру порвёт поперёк возле шва, а почему возле шва - да потому что арматурная сталь и так с мелкой кристаллической решеткой, так ещё будет и перекал металла в области сварки. Арматуру достаточно связать проволокой при некоторых условиях...
Se que en grandes losas en edificios en Asia para unir las varillas como si fuera una sola en tramos largos se le hace una rosca a la varilla y se van enroscando y aplicando una capa de recubrimiento antioxidante.
Несущию конструкцию тоесть каркас варят...проволкой тока ненесущие крутят и те которые экономят...связка проволкой подруземает что битон будит определёной твёрдости тоесть марки при застывании..но где гарантия...
Yo en su lugar, hubiera hecho un solape de mínimo de 40 centímetros y puntos cada 8-10 centímetros. Mucha Soldadura, hace que las varillas pierdan su rigidez, y el pilar o viga de hormigón pierden resistencia.
Работал сварщиком в арматурном цехе завода ЖБИ. Сваривали такую арматуру без всяких зазоров, и вся держалась как положено. После сваривания одевают шайбы на края, плющат концы, получается стержень для закладки в форму плиты перекрытия. Перед тем как заложить, растягивают
Одевают шайбы на стержень арматуры с другого конца Не с того что сваривают И чтоб шайба не слезла плющат конец со стороны шайбы И потом всё это в форму и бетон Посмотри ютюб про "преднатяг бетона@@user-hr5nc6xs3w