You can cut degree angles with most circular saws by adjusting the degree angle (her curcular saw has a yellow almond-shaped tab handle). You can also set up a fence for a large straight edge angle cut. It is a good idea to start with a circular saw and work your way up. You'll end up using each if you really get into it. And these tools have a resell value of some sort so take good care of them and keep the original boxes and manuals. I usually collapse the box down, tuck the manual inside and store these flat in the garage. I do it for just about everything I buy, so when the time comes to sell for lack of use or upgrade, I can get a better resell dollar due to care and original packaging. BE CAREFUL, EYE PROTECTION, NO LOOSE CLOTHING, BE FOCUSED, AND GO SLOW, NO DISTRACTIONS. Great video @WelcometoTheWoods
Your video clarified the purpose of all three saws--thank you. I've owned a circular saw like what you showed for over 30 years. I don't use it much, but wouldn't be without it. This year I bought a smaller, battery powered circular saw for cutting smaller lumber up to 2x4 in size. Given that the blade on these saws spin at 3,000+ rpm and cut off more than 4,000 fingers a year, there's no tool I respect and fear more than my two circular saws. I have watched countless RU-vid safety videos on the precautions to take when using such saws, as well as the ones you demonstrated, including accounts from people who's lives were never the same after an accident with such a saw. That said, I would like to offer a humble, friendly suggestion that you consider redoing the table saw part of this video where you demonstrate its use with all the safety equipment in place and using proper handling precautions. Safety equipment includes as a minimum riving knife, anti-kickback pawls, blade guards, safety glasses, and hearing protection, while handling precautions on the table saw include push sticks that keep your fingers far from the blade, not standing directly behind the wood piece being cut, minimize distractions (put phone on vibrate before cutting), strategize how the cut will be done before doing it (i.e., risk assessment) and not allowing the wood piece as it's being cut to come in contact with the saw's fence where the wood could be pinched between the fence and the spinning blade causing a serious, split-second, kick-back injury that could be life threatening. Because your intended audience is a DIY beginner, you would be doing them a great favor to stress the fact that use of these saws, especially the table saw, come with far greater responsibility for safe use than any other non-cutting, power tool in their shop due to high risk of injury. Also, it would be good to mention that if they are working alone, they should have their cell phone charged and on their person in the event there is an accident and they have to call 911. Perhaps it would be helpful to include one or two of your favorite links to other RU-vid videos for the safe use of each of the three types of saws you demonstrated. Doing so will give the viewers a greater appreciation for how beautiful and wonderful it is to have uninjured hands, and other body parts, and to not take such things for granted when using these powerful cutting tools. Thanks for your consideration. www.motherjones.com/politics/2013/05/table-saw-sawstop-safety-finger-cut/
Save your breath. If you watch many of her other videos, you'll see many of the safety issues you point out with comments mentioning them. She still continues practicing unsafe power tool use. Hopefully she starts to take the repeated comments about safety to heart.
Thank you for saying this. I'm a total beginner with power tools. Yesterday I had my first lesson with how to use an angle grinder (🙈 don't laugh 😂) I had bought all the safety gear, and my brother who works in a very industrial industry, didn't want to put any of it on cos he's a pro (which he is) I refused to begin until he did - my logic is that it's the one time you don't wear a face guard or leather gloves etc, that something goes wrong in a permanent live changing way. I must admit I'm a little terrified of it all at the moment 🙈🙈😬
After watching tons of mitre saw videos I finally got one and the first time we tried it, it started throwing wood pieces around! I ended up returning my brand new Dewalt mitre saw but I do agree these power tools can be dangerous and DIYers on RU-vid make it look so easy. I really do think there was a specific problem with that saw and I’ll get a new one. But this time, I won’t try it without all my safety gears lol
The circular saw is a versatile tool, but to prevent kickback, avoid setting the cut depth lower than what is needed to cut the material you work with. Also, keep a sharp blade on the circular saw to get a clean cut and not have to force the saw through the material. If the motor is 15 amps, always better to use a heavier 12 gauge extension cord. Every tool can do its job, but to be safe and effective, never rush the work.
Have all 3, but always use a push stick on your table saw keep hands at a safe distance. Been cutting for 40 years and still have all my fingers. Plunge, or track saws are a great addition also
I am an avid DIY'r. In short time, you will realize you need all 3 (and then some)! The right tool (saw, in this case) for the job makes life a whole lot easier, as i am sure you know. Great channel by the way. Really enjoyed those composite front steps.
Diesel. Great comment. If someone is tight on space and budget, I recommend the circular saw and miter saw should be the first two buys (for most DYI house projects). Craft projects need all kinds of stuff, but that's another topic.
Thanks for making this video. I only own a circular saw and I was thinking of upgrading to a miter saw but I honestly have not mastered the circular saw yet. This video was the confirmation I needed to keep my money in my pocket.
I was skepticle of a 20 volt circular saw. But I have several B&D 20 volt batteries and the drill Works great ru-vid.comUgkxjpBI8OOeUXib_iT7UomCrQ-uauwZJ62c . I saw the 4 stars and some glowing reviews so decided to purchase this saw. Well, leave your money in your pocket and run a cord because this little saw won't cut
So incredibly helpful! I was initially gifted a miter saw but exchanged it for a circular saw since I’m a beginner. Stumbled upon this video cause I’m having doubts if I made the right decision. Thanks for sharing!
Melissa, it makes sense to use and encourage proper stands for the table & miter saws. Much easier on the back. And wearing proper footwear & safety glasses would be advisable.
Great video this helped me a buch. I was debating whether to buy a mitre or table saw as part of a deck rebuild. But you made me realize the circular saw good enough. It never occured to me to put a straight edge down as a guide for the saw. Once I started doing that it changed the value of my circular saw. Thanks!
Although I agree the blade guard on the table saw can be a pain to leave on all the time but you should use it if possible. BUT you should ALWAYS have the splitter/riving knife on the table saw ALL of the time to prevent kickback. Nice video - thank you from the UK : )
A table saw is my favorite tool of all IF you have the room to have a big table saw with an extended table. Then you can cut an entire 4x8 sheet of wood or a small piece of wood both with precision.
@@prettyyoungthing1008 Ask 10 people and probably get 10 answers. Depends on budget and needs. Lowes has a really nice Delta saw and HD has a nice Ridgid one. Also others like Skil, Metabo, Dewalt are good saws.
Nicely broken down! I have made a bunch of things just with a circular saw as I don't own any other saw except a jig saw which I hardly ever use. It's possible to use the circular saw but every little cut other than a cross or miter cut can be a creative problem solving exercise. It takes time and sometimes the cuts aren't precise but most of the time, I have been please with how neat the joinery looks. I have even ripped boards to the right width and thickness for my projects. With that being said, I am struggling with cutting neat rabets and grooves for some reason. Leaning towards going for a table saw only. Good to know it can make miter cuts too. Why do we need a miter saw of the table saw does the same?
Thanks! I've had a radial arm saw in my garage for decades (which I bought from the previous home owner) but I sold it because I couldn't justify the amount of space it took up (and far more dangerous than these). I've always had a circular saw, but never owned a miter or table saw, so this video is very helpful. I had no idea there were battery powered miter saws. Mind blown. That might be perfect for the small jobs I have to do.
If by "angle cut" with the circular saw you mean a bevel cut (like what you did with the table saw at the 8:30-8:40 mark) you can do those cuts with a circular saw. You just loosen the yellow knob on the front of the saw (you'll see the arched piece of metal with numbers on it) and adjust your plate to whatever degree bevel you need and then tighten the knob back down and make your bevel cut. If you mean miter cuts though you can make those as well. Just set your guide (like you do with a straight cut) and cut at whatever angle you'd like. :)
A good replacement for your miter saw it's a radial arm saw that will allow you much longer cut and do the same purpose and makes excellent miter cuts I also recommend that beginners with a table saw to use the guard it really isn't inconvenient if you learn to use it with the guard from the beginning and as time goes on and you feel a little more comfortable the guard can be removed be sure with the table saw you also have a good push stick to push your wood through rather than running your hand along the wood in between the fence and the blade not recommended and always safety glasses very nice.
Thank perfect beginners guide. I really like the mitre saws, but the circular saw will be much more versatile for me as a beginner. I will definitely get a mitre saw down the line as I like the whole set up with the fitted base. As for the table saw, they look a little intimidating tbh but a greatly space saving option. 😊
Thank you for the DIY education. I love your infectious smile and enthusiasm when you introduce each of the saw. It is genuine and authentic. Awesome !
Guards get in the way, yes that is the purpose. Please reconsider a guard and a correct width riving knife. Table saws can be so dangerous, so taking extra precautions is paramount to your safety. Love your channel, very creative and enjoyable.
My favorite is absolutely the circular saw. You can replace the miter saw with the circular saw and a square. You can also replace the table saw with a circular saw with a track. Plus it's much lighter and portable.
I have all 3. I don't use a circular too much, as you get more error when cutting free hand. I build beehive equipment with them mainly. I use the table saw to rip the long boards down to width, then use the miter saw to cut to length. I am planning on cutting down a granite sink top for my bathroom project, which will probably involve the circular saw for that. I need to take 2" off each end to keep the sink and faucet centered. I will then use the table saw and compound miter saw to build a new cabinet and doors for the sink top.
I don't have the battery powered miter saw. I didn't know they even made one. Great idea cutting boards to fit at the store. I have that exact table saw plus a large one with cast iron extensions. I have a miter, 2 of which you can make your cut a pull it toward you to cut wider boards. I Father was a carpenter so I inherited all his tools. To many to list. Bless your heart, I love your channel. Battery powered miter saw. Hummmm !
I stumbled on this video. I've really been trying to decide which one to get (table saw is out if my range at the mo) but even though I know (now) the circular saw seems to be the most logical, that's the one that scares me for some reason 😬😳🙈 ... thanks for explaining the difference, similarities, pros and cons. Very useful video.
I bought a circular saw as a beginner in wood working. A table saw is still very expensive for me and also higher energy consumption. Thanks for this video, so I know what to buy next 🙏
Just getting into working and have been doing a lot of research. The only saw I own is a hand saw and plan on purchasing my first circular saw in the upcoming weeks.
I have to agree with some of the people who posted about some safety information and implementation from you in your videos. I have been a woodworker most of my working life and safety has always been a part of my work environment. As much as I appreciate your cute legs; your working in sandals and bare foot a lot of times is downright dangerous and could lead to a serious situation. Another thing that I find interesting is how you almost always work on the ground or garage floor when cutting with your tools. Another thing that can be and lead to a lack of control. As an older person; I worry about your back if you continue to work that way as long as I have done. Have you tried to put your tools on saw horses or on your great work winch you made in a video? I am not sure I have ever seen you use ear protection or a dust mask. I enjoy your videos and your design mind but as a foreman in big shops including in Antarctica; I have been in charge of osha run shops where safety measures are insisted on. I feel that some of the DYI people that watch you could benefit from some info and modeling of such subject matter. You may disagree; you make your own choices but I have seen too many injuries as a result of lack of safety measures.
As a master carpenter myself….I couldn’t agree with you more. The video has good intention but is boarder line good information for inexperienced people looking for some advice.
Miter saw is perfect for quickly being able to cross cut relatively narrow pieces like a 2x4 to correct length. Table saw is good for ripping pieces like making them narrower and also doing jig cuts. Both have their place depending on what you need but table saw can be at times more versatile in the fact that you can rip and cross cut pieces of various dimensions with it. With miter saw you can only cross cut narrower pieces but it’s quicker to cross cut with miter saw and gives you straight cutting edge. Miter saws also have capability of doing angled cuts very easily.
@@DheeraVenkatraman never worked with a sliding miter saw. But I see your point. Question I have then, is there any reason why you would have regular miter saw versus a sliding miter saw? Are there any cuts you can perform with a regular miter saw that you cannot with a sliding one?
@@Gaba-oo4qb Basically no. A sliding compound miter saw is just a compound miter saw that slides back and forth. So there are no cuts that you are missing out on. It's slightly more pricey but I'd say it is extremely worth it. In general if a cut can be done on a miter saw I would ALWAYS pick the miter saw over a circular saw or a table saw, if at the very least for safety and ease of setup. I only reach for those other tools for cuts the miter saw cannot do.
Thanks a lot for your video. Helping a beginner like me. I have been asking for help and got lots of different answers to exactly this question, now I know that what I thought was similar to your idea. Will get a circular saw with the possibility to tilting. Looking forward for more videos. Thanks
Very important if you would like to saw with precision. (avoid torsion as much as possible)! Always choose a Miter saw with a handle positioned in a vertical line above the saw blade. Everything must be aligned, slide rails, handle, and saw blade, it is much better this way the blade will not tilt. Because there is some torsion in the aluminum housing . And choose an engine with softstart on it to prevent wear of the gear and worm shaft. It is very important that everything is aligned. Here are some examples to show how the handle must be positioned above the blade. Bosch gcm 800 sj / Bosch gcm 8 sjl / Evolution rage 3 / FESTOOL KS 60 / / HITACHI C12RSH2 / FESTOOL KS 60 E KAPEX / Metabo KGSV 72 Xact . (This also is the case with the Miter saw without the slide rails). If you want you can test it yourself at home if there is torsion in the aluminum housing. Step-1. First you make a saw cut from +-5 mm deep in to a flat piece of wood. To this with the normal handle positioned on the right side of the Miter saw. Step-2. Then repeat this by pushing the saw blade down with your hand (finger) on the aluminum protective cover were the saw blade is cased in. Just now only do this without the running engine. Step-3. Now you can see if the saw blade will be positioned in or next to the saw cut.If the saw blade is (+- 0,2 / 0,5 mm) next to the saw cut then there is torsion in the aluminum housing. Step-4. therefor it is much better to choose a Miter saw with the handle positioned vertical in line above the saw blade.
Excellent video all the saws are useful in their own way another useful addition would be a bandsaw I have just bought one and it is now my go to saw for most jobs. Really like your videos.
Please be careful with the table saw, don’t take any short cuts and get a micro jig or something similar for the table saw. I now have 9 1/2 fingers and 70 stitches where I thought the wood was wide enough to push my hand up to the blade, but kickback pulled the hand in
Thank you for the video. I have been trying to determine what to buy between the miter saw and table saw. Reason being that I want to be able to cut rabbet joint but also be able to cut angles. The only missing information is whether or not the table saw can be set up with a rabbet joint "blade".
Without a doubt. Especially if you are working from narrower pre-sawed wooden planks and mostly just need to cut them to length rapidly. A sliding mitre saw will give you additional options for slightly wider wood too. They are even great for cutting angled or box steel with the right blade attached.
I have been doing DYI work for the last 5 years. I have collected dozens of tools from Milwaukee, starting from drills. Saws were among the last that I got because they are the most dangerous and I got two young boys. I remember damaging (and almost hurting myself) my $500 milwaukee fuel mitre saw the first time I used it. I had to read the instructions twice when I replaced it. They arent a joke. I still dont have a table saw...
I think this video is great but I would encourage you to add more footage about the table saw and the safety guidelines that are to be observe for a safe operation, the reason I ask you this is because anyone that buys a table saw must be made aware of the responsibility that comes with it, since it provides the least of safety guards as it is meant for people to use it to be fully aware of what the are doing (i.e. like never position yourself directly in front of the saw, or the best way to push the material to cut, etc...) the circular saw and or miter saw somehow represents a much more controlled and safety environment due to their own design, and while they also need to be handled adequately they are less dangerous compared to the table saw.
My table saw is a lot smaller than yours... so you can get smaller ones. I have two circular saws. I use one with diamond blades for cutting cinder block and patio stones. It was super cheap, so I wont be too upset when I burn out the bearings from all the rock dust. I use the other for cutting wood. The one thing you didn't mention about circular saws is that it's more difficult to get straight cuts. That they are so mobile also makes them a bit wigglier when you're cutting. You used a fence/jig/guide whatever, but even with those, you have to make sure you keep constant pressure on the fence/jig and that your fence/jig isn't moving around too. I have a miter saw that's a little bigger than yours. It's the saw I use when I want my 2x4's cross cuts straight. As I said, I have a table saw too. It's smaller than yours. The problem I have is that the wood gets wiggly if it's a big piece. I also have a radial-arm saw. It's like a very large circular saw in that the wood stays stationary and the saw blade travels. Mine has a 10" blade, but because of the size of the motor, I still can't cross cut a 4x4 in one cut. You talked about setting the height of the table saw so that the blade is just above the piece you're cutting. Actually, the circular saw and radial-arm saw are the same. The blade of the spinning saws are more efficient and produce better results if the sharp points of the blade hit the wood at the correct angle. On a circular saw, you would set the depth to about 1 5/8 to cross cut a 2x4. I have a jig saw, which you show but don't talk about... and a scroll saw, which is sort of like a table mounted jig saw. I have a reciprocating saw... which is like a oversize jig saw on steroids. I use it for mostly demolition and small landscape projects. And then... I have a chainsaw.... when the chain is sharp, it can turn large pieces of wood into small pieces of wood really fast. My parents gave me my first circular saw for my 16th birthday. My table saw was my grandfathers. I got it when he passed away. The radial-arm saw was my dads. One additional thing about table saws and radial-arm saws... you can get attachments that allow you do do other things with them. I have datto blades that allow you to make extra wide cuts. I have shapers that allow you to make fancy shaped cuts. I have sander, lathe, and drill attachments. I also have an attachment that allow you to cut out a circular piece.
@@baxterenrife are you dense? is that your poor attempt at a joke? With your intellect would anyone actually be surprised if you cut off your other index finger?
Just like to add - Safety glasses, ear muffs and a dust mask are essential gear to use while using power tools and can save a trip to the emergency room. They are inexpensive at the home stores and work well.
How would you make a long cut on a narrow board such as a 2.5" or 3" wide baseboard? The tiler took out only part of the baseboard in the utility room. Now I need to match the baseboard on the other wall with tile up to it. I need to cut a long narrow cut along the baseboard he took out where the tile goes up to the wall. I'm thinking circular saw and clamp down the long baseboard and carefully cut the long narrow cut with a circular saw. I don't own a table saw.
Very good and informative video. I own a circular and miter saw and would love to have a table saw but I do not have room in my garage. But, the one you have is like a table model which I could store and use. I just may look into getting one of those and your DeWalt model looks like a good one. Thanks for the lesson on saw types.
Thank you for this video. It was really informative. I currently have a circular saw which can also be angled to a certain degree. I was looking to level-up and invest in a different saw. At this point, for a beginner-intermediate woodworker do you suggest a miter saw or a table saw? I'm leaning more towards the table saw but I'm hesitant since like you mentioned its quite an upfront investment. Are there other considerations when looking for a table saw?
As a DIYer, for me safety is foremost and hence my first power saw was a jigsaw. It was like a hand saw where I did not have to slog. Next I bought a hand saw because I found very good one at a good price. It was intimidating and all the videos on RU-vid scared me. So I got a track saw. I like the idea that the blade goes to the wood so the kickbacks are not there. But for repeat cuts I think a miter saw is a safer tool but it cannot be used for larger cuts. So I am confused between table saw and miter saw. Since I also need to work with aluminium I think miter is a better and safer choice but who knows I might end up finally buying table saw as well. Please do a video keeping in view of safety point of view for a DIYer.
Glad you are explaining basic tools pros/cons. Have you done a video I don't see yet on planers? I thought I was going to seek a DeWalt, but today I was at a woodworking store that sells Jet 13" Helical Style Bench Top; seems the stainless steel vs aluminum could be an a perk? My project is to make a 10'x4'x3" kitchen island butcher block to place on island base already in place. They thought I would regret running 10' boards through that planer size though....thoughts? Thanks.
Table saw can be useful when you're working with large plywood or piece of wood. A miter saw and circular saw can do everything a table saw does. Even you can use a miter saw for making dado. Most of the miter saw has a stop bolt that allows you to do that. But a router is much preferred for that. Moreover table saw is more dangerous. For newbies, table saw isn't recommended. But if you're experienced then, it's time for you to play with a table saw. This is all my opinion. Thanks 😊
Also if you want to cut bevels and miter cut more precisely, then miter saw is perfect than table saw. Also it allows you to cut small pieces with just a push stick while table saw need a crosscut jig.
Great video. But please, use a riving knife on that table saw. It prevents over 80% of the kickbacks. The table saw is a wonderful tool but its so dangerous, the 1st or 2nd most dangerous, competing with the chainsaw. Also, there is GRR-RIPPER pushblock which is a very convenient push block and safer than most push sticks. But yeah, i agree with the video, although i ended up buying all three because the the work is easier when you're using the correct tool for the cut.
Great Video clip! Sorry for butting in, I would appreciate your initial thoughts. Have you considered - Schallingora Dexterous Programme Scheme (erm, check it on google should be there)? It is a smashing one of a kind guide for building any shed in no time with no experience without the normal expense. Ive heard some unbelievable things about it and my friend after many years got astronomical results with it.
Just getting started with some woodworking and I have a Dust Collection system and HF circular saw. Nice overview, probably table sax next. Keep broadcasting!!
The way to look at it is they each do their own different jobs. But, I agree that if you're just starting DIY and need something to do a few cuts a circular saw is better. They're more portable, and being smaller they're easier to store without needing a whole workshop. Fundamentally, a circular saw is a hand tool, you take it to the work, which the compound miter and the table saws are stationary tools, you take the work to them. If you have a lot of cuts, and a bunch of projects to do, then it would be good to get a compound miter and a table saw.
