The Ultimate NAPA compressor! Part 3: Install

Подписаться 8 тыс.

50% 1

In this video we will go over the install and wiring of the ULTIMATE NAPA Compressor.
Don't for get to go back and watch the previous videos in this series:
Part 1: • The ULTIMATE NAPA comp...
Part 2: • The ULTIMATE NAPA comp...
Support the channel here: 22e989-2.mysho...
Here is the parts list:
www.amazon.com...
www.amazon.com...
www.amazon.com...
www.amazon.com...
www.amazon.com...
www.napaonline...

Опубликовано:

30 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@theghostoffrankgrimes5621 2 месяца назад

0 gauge cable, you impress me sir! Well done from Australia 👍🏼 (The only thing I can see that’s been done wrong is ur steering wheel is on the wrong side of the car 😜)

@theschultz-ster 2 месяца назад

Thank you mate! I've always wanted to drive on the right hand side of a car, on the other side of the road too! That has to be so weird the first time?

@Reelpeelingadventures 2 месяца назад

Thanks for airing me up the other day

@theschultz-ster 2 месяца назад

No problem

@Reelpeelingadventures 2 месяца назад

Those peering T rex eyes barely able to see over the hood😅

@theschultz-ster 2 месяца назад

Bahahah

@adventure_next6869 2 месяца назад

So I have added the relay and pressure. I am wanting to go straight from the compressor to my aux beam fuse box. How would I hot about this?

@theschultz-ster 2 месяца назад

The wire I ran for my rock lights had a third conductor in it. The yellow wire in the video. I ran it to one side of the pressure switch and the other side to the relay. Here is the link to the wiring video I made for this project. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-RLQnmI3LxGs.html

@theschultz-ster 2 месяца назад

I ran the wire in the frame rail, from the front to the back.

@adventure_next6869 2 месяца назад

@@theschultz-ster I have a 4Runner so the compressor will be under my hood over to the left and aux beam on the far right. I do not know too much about wiring so I guess that is where I am getting stumped.

@theschultz-ster 2 месяца назад

@@adventure_next6869 It will be simple. Just run a wire from one of the lower amp outputs of the auxbeam(mine is #1&2) to one side of the pressure switch, from the other side of the pressure switch run a wire to the positive trigger on the relay. the wire from the auxbeam to the switch will go along your firewall is my guess, or around the front over the radiator. Hope this helps.

@adventure_next6869 2 месяца назад

So when you mean wire, are you meaning the gator clip power wires?

@adventure_next6869 2 месяца назад

Should make a walk through how to

@theschultz-ster 2 месяца назад

What parts? I can make a more in-depth if needed, no problem

@adventure_next6869 2 месяца назад

@@theschultz-ster how you wired everything after you installed all the parts from one. I guess the wiring from the compressor to the aux beam panel and battery. There are so many of us out here who are looking for these and I would get your names and videos out there

@adventure_next6869 2 месяца назад

A lot of in the 4Runner community and jeep community could use it

@theschultz-ster 2 месяца назад

@@adventure_next6869 do you have an email address? If you would like you can direct this video.

@adventure_next6869 2 месяца назад

@@theschultz-ster I left my email but I think YT removed it.