This Trick Few People Know! Tips To Change Pvc Pipe Corner Joints Without Water Lock 

These tips are probably good for a beginner. But as a professional plumber for 8 years let me give you some advice; the flow of the water doesn't necessarily have to be off. In fact I've put PVC together with more flow and pressure. Sometimes you can't turn it off. Best bet is to open that spigot at the end first so when you do get it back together it doesn't have the full pressure and no glue will stick the valve. Also you don't need the union, it's useful if you ever intend to remove it again like on a pump or a well pump that might be difficult to fix in line, typically use two unions so you end up with a piece in the middle like this: |-----| and keep the threaded part on the piece and all you'll need is a tiny bit of play and some channel locks will take it right off. I would advise using two couplings or (even better) two bell ends. The clear glue is a good route, it's easier on the hands and cleans up easier but ditch the heat gun, just get cut back farther, and please some primer. The heat gun is actually bad long term, heating pvc to that temperature where you can remove fittings will make the joints brittle over time, especially when exposed to sunlight/open air. I would start with the side where the water isn't running, get it cut and glued and let it sit maybe 5 or 10 minutes, then prime both ends, glue both ends and stick it together and hold it in place for 30 seconds to a minute. You NEED to start gluing BOTH ends. Inside the fitting as well. Prime both ends. It works best when you prime the fitting and the pipe and then immediately glue the fitting and the pipe, make sure to apply the fitting or pipe in a way you can turn it (once it's on) a good 45 degrees. So you want to put a fitting, say an elbow that faces left < you want to put it on facing up ^ or down v and THEN turn it the right way and then hold it together. That allows the glue to mash up and coat the inside. Best scenario I've found is if you're gluing free pieces of pipe like putting valves together before installing in the ground or pre-fabricating a long piece, I find it's bullet proof to put a good bit of glue, then spin the fitting or pipe in your hands and watch the beed of glue coat the inside lip of the fitting or pipe and keep rolling it if possible to get that lip completely sealed. Again, this works best on free pipes that aren't fixed in position or in an open ditch or wall you can work with more freely. Best luck

Great tips for repairing PVC pipes

Very solid trick. congratulations

A good plumber always has good tricks. thank you

great. Please continue your work. you have very good tips

Thank you for showing me cool tricks at work

very impressed with your tips

Thank you for sharing this tip with us

Awesome plumber with cool tricks

Amazing job. Be blessed

Thank you for sharing useful tips

the tips you shared is very good

thank you for sharing practical knowledge

your tips are very good and practical

Thanks for your useful ideas.

you do very well. Congratulations

very creative and practical tips

Very helpful for everyone

very good trick. thank you

Your idea is great

After watching this video, I realized that human creativity is outstanding

I like what you are doing. good tips for life

I love real videos like this. great tricks

Thank you ! very interesting tips

very creative. good tips

repairs will be easy with these tips

thanks for your tricks

great tricks. thank you

Clever method for repairing pvc pipe joints

Thanks. I'll be applying this trick to my plumbing

Nice and creative tip

You did it pretty well.congratulations

Smart connection. thank you for sharing video

Amazing simple tricks

Thank you so much for sharing tricks

Thank you for sharing this great tricks

2 great tricks, congrats

very good. congrats my friend

You are very experienced in plumbing

you did a great job

Useful tips for everyone

Amazing tricks to repair pipes

I will definitely use this tricks

Great connection tips. I will try it

great tips. Thank you for sharing your knowledge. Good luck.

very good fix. congrats with cool tips

great repair tricks

very creative. good ideas

great advice, thank you for telling me many cool tricks

nice and interesting tips my friend

Work becomes easy with good tricks

i have done it. very good

you are a very creative plumber

wow. great tricks

Great idea

very sure. great trick

Very interesting idea, great

You are one smart cookie!

The tips you did is great

Each of your tips is very good

Great tips

very good. nice tip i really need it

great repair tips

thanks for the good video. great connection tricks

very good video with interesting tricks

Thank you for showing me something interesting

I will do it right away. very nice and helpful

Smart tips. I am very impressed with it

Have a nice day. great tips

Very creative way of working. congrats on your tricks

great ideas for us

nice tips. It is applicable to all plumbing

you do very well

good connection. i really like your trick

very solid and durable

very good connection. congrats video with cool tricks

Its a great creation

Thanks. I will use this tips

Innovative trick for fixing pvc pipe joints

great tips, thanks

very interesting tips

easy to understand and easy to implement

very useful tricks

Great. good tips for me and everyone

congrats on your tips

very good my friend. great repair

the tricks you do are amazing

you make it very realistic. good tricks

Perfect! I have accumulated a good tip

great tips bro

Great tricks

very creative and amazing tricks

This trick I think will be very helpful for everyone

Great. With this trick, no need to lock the water, it still works well

nice trick, very good to apply

Great idea, good work

It's great to have these great tips

wow, interesting video, cool trick bro

good tips. very creative

I love practical tips like this