Thread milling manual CNC PROGRAM writing training in Tamil 

I am learned a lot of knowledge from this videos

Good learning .. Thank you Could you explain Center point feed and contour feed difference in thread milling program .

Very knowledge full video

Bro starting la iruthu thana ending poganum niga thread aha end la iruthu starting varra mathiri solluriga

Anna super explanation thanks anna

1 inch bsp thread video podunga anna

Sir thread mill tool two side insert sem concept thana...

Thank you sir.its very useful

Thank you

HI Bro, Have you done any video on tooling hole manufacturing and outside edge blend using form releived cutter. If so please let me know need to watch those video.

Super

Hi sir, why cutter compensation G40 is not used for each pass.

One question is if I have thread depth as 25mm but depth of the part is 30mm. Hole should be through hole , How it will be manufactured. If Iam not wrong. Firstly through hole will be drilled and then thread milling will be done ?

Sir, npt thread milling program explain pls

புரி வெட்டுவதட்கான மிக இலகுவான முறை, cam i விட மெஷினில் வேகமா prg செய்யலாம் Exs… Thread M8 (Pitch 1.25) deep 8 mm T5 M06 G54 G00 G90 G40 G80 G00 X0 Y0 S2200 M3 G43 H5 Z20. M8 G00 Z1. G1 Z0 F400. G1 G42 X-4.D05F225.(4+4 = 8/M8) G2 I4.Z-1.25 G2 I4.Z-2.5 G2 I4.Z-3.75 G2 I4.Z-5. G2 I4.Z-6.25 G2 I4.Z-8 G1 X0 G40 G00 Z20.M9 M30 % (D5 Tools T5 Radio’s)👍 not G41 /G42 ✅ (I4. not 14/ i4) * இப் போர்முலாவை பயன்படுத்தி நீங்கள் எல்லா thread ம் செய்யலாம் தனியா நீங்கள் Pitch ம் அதே ஓடர் இல் deep ம் மாத்தினால் போதும் . Quick Program.

Taper boring calculation explain panunga adula minor id 8 degree kudutha antha value eppadi kandupidikanum solunga anna

Vtl thread insert bar la iruthu vmc machine la thread mill program epadi panrathu

Thanks👌👌

HMC la thread mill adikama mudyuma sir

Thala , oru doubt !! Thread mill oda pass complete aaga solla , G90 la cutter ah work zero ku kondu Vara solla , cutter compensation cancel ( G40 ) kudukka venama ... Straight ah G90 X0. Y0. Kudutha compensate cancel aaiduma ??? Please clear pannunga thala

Thread mill depth initial LA erunthu start pannra mathiri eruntha depth calulathion ethey method tha use pannanuma Arc forming calculation puriyala innum koncham etailah explain panna mudiuma

And also blind hole ku arc calculation sonnenga la , adha Konja block ah ezhudhii ... Represent pannenga na , enaku konja puriyum nu nenaikran... Help pannuvengala

Bro diagram degree machine calculation konjam video podunga please

Which place training center

Hi bro cnc bspt id fine , threading program

Super bro

Bro 1 inch-25.4mm. 3/4 inch-26.441mm eppadi varum bro.please koncham thelivuvaa sollunka bro

How to select the feed and speed for thread milling

All type off vmc tap pitch calculations pls

For borewell rod adapter

Sir 1.5 mm OK but 2mm ennang sir puriyala

Sir , corner arc.2 chamfer 1×45 manual calculation sollunga solluga

Tools spec soluga sir

Sir why calling by inch not calling mm why bro please share me bro

Bro cutter compensation D03 use pannirukinka appo max dia (26.441÷2)=13.2 so X13.2 and I-13.2 thana kudukanum bro.pls reply bro

G 40 cancel pannula

Anna interpolation la end mill use panni program eppudi podurathu na

sir maryland thread chart dowload link send panunga......

Taper turning and taper threading sollunga

Hi

Onnum puriyla