Subject - Metrology and Quality Control
Chapter - Derivation of Effective Diameter using three Wire Method
Timestamps
0:00 - Start
0:08 - Three Wire Method
0:29 - Effective Diameter of threaded workpiece
1:34 - Derivation of Effective Diameter using three Wire Method
3:05 - Diameter over the wire
3:48 - Metric Thread
4:15 - Whitworth Thread
#Three_Wire_Method_Derivation
#Effective_Diameter
#Metrology_and_Quality_Control
#Screw_Thread
#Mechanicalengineering
#GATE
#Mechanicallectures
#Mechanical_Engineering
#shubhamkola
This Video Topic is from Metrology and Quality Control Subject, you can also watch below mentioned videos related to Metrology and Quality Control Subject:
Dial Gauge Indicator (Mechanical Comparator) - • Dial Gauge Indicator W...
Sigma Comparator (Mechanical Comparator) - • Sigma Comparator Worki...
Solex Pneumatic Comparator - • Solex Pneumatic Compar...
Sine Bar (Angular Measurement) - • Sine Bar Working Proce...
Bevel Protractor (Angular Measurement) - • Bevel Protractor Worki...
Clinometer (Angular Measurement) - • Clinometer Working | A...
Autocollimator (Angular Measurement) - • Autocollimator Working...
Profile Projector (Optical Comparator) - • Profile Projector Work...
Floating Carriage Micrometer (Screw Thread Measurement) - • Floating Carriage Micr...
Screw Thread Terminology (Flank, Pitch, Root, Crest) - • Screw Thread Terminolo...
Types of Screw Thread (V Thread, Acme Thread, Buttress Thread) - • Types of Screw Thread ...
Two Wire Method (Derivation of Effective Diameter for Thread Measurement) - • Two Wire Method: Deriv...
Three Wire Method (Derivation of Effective Diameter for Thread Measurement) - • Three Wire Method: Der...
Best Wire Size (Screw Thread Measurement) - • Best Wire Size in Scre...
Parkinson Gear Tester (Gear Inspection) - • Parkinson Gear Tester:...
Gear Tooth Vernier Caliper (Gear Tooth Thickness Measurement) - • Gear Tooth Vernier Cal...
Limit, Fit, Allowance and Tolerance - • Limit, Fit, Allowance ...
Hole Basis System and Shaft Basis System - • Difference Between Hol...
How to Solve Problems on Slip Gauge Set M87 and M45 - • Problems on Slip Gauge...
How to Solve Problems on Angle Gauge Set - • Problems on Angle Gaug...
Your Queries :-
What is three Wire Method
three Wire Method Uses How Many Number of Wires
What is the Derivation of three Wire Method
How to Determine Effective Diameter using three Wire Method
How to use three Wire Method
How to measure effective diameter of Screw thread
Faculty - Shubham Kola ( BE Mechanical Engineer )
Email ID - shubhamkolaofficial@gmail.com
From - Maharashtra ( India )
RU-vid Channel ( Shubham Kola ) - / @ifinfotech
Disclaimer -
video is for educational purpose only. Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favour of fair use. The content in this video is collected from books, media, internet space etc. This is strictly for educational and information purposes and is not intended to be advice or recommendation of any kind whatsoever. The faculty is not a subject expert. The faculty is sharing his knowledge in the form of videos. The faculty giving small basics information on mechanical engineering topics. We endeavour to keep the information up to date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the video or the information, related graphics contained in the video for any purpose. any reliance you place on such information is therefore strictly at your own risk. In no event will we be liable for any loss or damage without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arise out of, or in connection with, the use of this video.
(*The music used in my video, is not owned by me!*
Source*RU-vid Music Library)
2 авг 2024
