I’m new in this field and I’m learning a lot from watching your videos. I appreciate the videos you upload. I’m hoping to get to your level at one point.
great presentation. on trucks with high hours I have found that the internal strainer filter in the valve chest ontop of the transmission gets blocked. often people just replace the filter. if you don't flush then change the ATF and filter it will block again. once again I learnt that the hard way.
Thanks, great video, after your pico scope video I was inspired to watch the rest of ur vids for while I may not work on forklifts, I appreciate your methodology.
nice videos thanks I have question I have forklift hyster h50 xl start but when I push pedal for aceleration cut off I have to put my hand on hold fron air filter runs fine if I take my hand off the forklift cut off
Thanks for the check light thing, never thought of it it also would limit current vry cool and the t-pin type will change how I do things moving forward, like every day. You should get a Fluke multimeter, this would take like 3 minutes without any power involved.
I do have a fluke multimeter. I like using a test light on simple loads such as relays, lights, solenoids because its quick and easy to do a bypass test. The bulb would limit the current going through, as you are basically connecting the test light in series with the load.
Cvt transmission angage reverse gear but no angage farward gears possible problems? I am auto engineer filter wash cvt fluid change but no result please solve problem this is mechanical problem or electronic?
Just started working on toyota lifts at work . I have a 8fgcu20 I think , smaller hard tire dock forklifts and when you hit the brake pedal going forward it will almost throw you out the seat , when in reverse they operate normally and gradually stop you without jarring any tips ?
I have one with the same issue. Solenoid and clutch packs are fine as I had it going forward with a bypass test. Direction switch works and It can't be the relay as swapping the relays around doesn't swap the fault. Must be a broken wire somewhere surely?
+Mathew Hansen no. On the dip stick there is a level for hot or cold. I usually run the engine to running temp, kill the engine then check the level using H as reference.
I have RR B3 reach truck error E107 occurs after some working with reach truck. Anybody tell me what is the problem. I have replaced the battery but same condition
Hey buddy, im having problem with no forwards or backwards, i have power to either side of plug to solenoids on transmission when switching lever to forward or revers, also done a bypass test. so we stripped the transmission, the solenoids seemed fine when we tested them as we could hear them opening or closing when power was put to them, all internals of transmission looked fine as far as im aware apart from internal strain filter which was clogged. but cannot see any other problem internally on transmission, still yet to put transmission back in but struggled to find any issue at all, where else could i look?
Hello colleague, excellent video and explanation of the follow-up of the failure. question, can you share the technical information of that equipment, the electrical system diagram, best regards, Milton Apraez
I have the same issue and completed all the troubleshooting procedures you posted. I do have power on my assembly switch and when added 12v to switch wheels move forward. Is my issue coming from the relay? Thanks in advance
Hello boss my forklift here seem broblem no forward only revers can direct batery curent have i, change all clutch pak. All oil ring oring all. But seem no forward. What is the problem this thank you
Hi I my company has a Toyota forklift model #8FGCU30. Original problem was lift jerking when in forward gear then lift was not driving forward or reverse. We changed both solenoids, torque converter and replaced all the parts in the transmission. Now lift moves forward but does not reverse, engine only revs. Any advise will be appreciated. Thanks.
hello i have 1 problem, toyota geneo R 1.5 ton forklift. error code fe -2 fe-1 . when the car is going fast, it gives an error and then it runs at a slow speed, please help me
i have attended one concern for Toyota forklift. in this forklift up and down move not working. hydraulic pump solenoid switch current do not come. all fuses ok but one relay ignition current do not come. please help me sir
I think what you are referring to is the inching valve. On a forklift the third pedal is called an inching pedal which releases the forward or reverse clutch for the operator to feather the movement of the forklift or to release the clutch completely.
I use TOYOTA forklift. Now days TOYOTA MODEL: 6FBRE14 electroforklift steering wheel is not working. I couldn't find service center of TOYOTA from UZBEKISTAN. Can you help me to fix this problem?
I have a problem with my yale 2011 4 tn, doesnt drive reverse. Do i have to do the same? or how does this change, do i need the electric diagram? thanks
+ForkliftGeek I've got one that doesn't have forward. I put battery volts to that connector at the transmission and still no luck. so I replaced the solenoid. still nada. I verified I have switched voltage at the connection. there's no possible way the relay would be bad if I have all of those things, correct? I found a plug for the forward valve broken, but I could still freely move the valve in the bore and the valve would spring back like it should. all of this after a pm. go figure. any thoughts? btw your videos are very informative...even to veteran lift techs. keep up the good work
I think some of these have 4 wires in the connector instead of two. Two wires mean the solenoid is grounded to the body if four then the other two would be ground wires for each solenoid. The most effective way is to use a scope to look at the current and voltage to see if the solenoid is really opening and closing. Using a current clamp and comparing the current to the reverse would give an idea if the solenoid is operating. If the solenoid is shifting the spool, then pressure tests would be my next step.
Hi I have mitsubishi for klift and same time is show f85 then is not moving forward and when I switched off and start is wark but it's keep many times like this
Hello how are you, I would like to know what the problem was, since I do not speak English and use a translator, and what you say at the end of the video does not translate it to me, thank you
Hi I have Toyota 7FBH20 Forklift but when accelerator presse so not working lifting Disconnected pump drive motor or not showing error can you help me sir.
Sir not showing error code I was checking all connection one by one .and also I will change CPU bord and accelerator switch but same problem sir ..battery forklift 7FBH20.....
¡Hola colega! ¿Por casualidad tienes el diagrama eléctrico de ése montacargas o el manual? Te agradecería si puedes compartirlo conmigo. Mi correo es jcegarra64@gmail.com
+Rene Trevino well, if your truck is exactly like the one in this video then it could be a cope of things. One could be the accelerator potentiometer, the electronic throttle body, or it could be that the computer is not allowing the engine to Rev up because it sees a fault (limp mode).
+Shabbir Hussain code CO is drive circuit abnormality fault. Everything concerning the drive circuit is suspect, but I'd start by checking the motor brushes.
+Shabbir Hussain code CO is drive circuit abnormality fault. Everything concerning the drive circuit is suspect, but I'd start by checking the motor brushes.
+Luis Elias when u say its stuck in reverse do u mean it just drives in reverse and not forward? Or just drives in reverse no matter what direction u choose.