Toyota Tacoma 2005-2020 3" Suspension Lift by Rough County (Tutorial How to video)

Подписаться 74 тыс.

Просмотров 43 тыс.

50% 1

3" suspension lift on this 2018 Toyota Tacoma 4WD. This kit fitsToyota Tacoma 2005-2020 and is Rough Country's 3" Suspension with lifted struts. In this video we go step by step on how we installed a 3" rough country suspension lift with lifted struts and install 17x9 Fuel Wheels and 33x12.50 17 BFG KO2.
Suspension details:
The power of N3 also arrives for Toyota Tacoma, as part of the new 3in N3-Series. This easy to install kit features 2in rear blocks and front upper strut extensions. With our new N3 Shocks, this kit takes your Tacoma to the next level; perfectly balancing off road performance and smooth highway ride.
FEATURES
Easy installation
Increased ground clearance
Maintains factory ride quality
Levels the front with the rear of the vehicle
Struts spacers require strut disassembly or strut compressor for installation.
Includes application valved N3 series shock absorbers which offer the best in balanced performance for on and off-road use.
NOTES - IMPORTANT
Requires minor cutting
Does NOT fit models with 5 lug wheels.
Does NOT fit T/X Baja models.
Does NOT fit XSP-X models.
Buy this kit directly on our website:
Strut spacer kit:
breakersmobile.com/product/ro...
Lifted Struts( same kit as in video)
breakersmobile.com/product/ro...
Vertex Coilover upgrade:
breakersmobile.com/product/ro...

Авто/Мото

Опубликовано:

6 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 42

@Its_about_that_time Год назад

I wish someone would show us a video using only jackstands. It's so much easier when you have a lift

@Srchief28 3 года назад

Very well done video. Not rushed and very clear

@Glenn.Cooper 2 года назад

This is a great video! Thanks for putting this out there.

@jpallen719 3 года назад

High quality video!

@BreakersStereo 3 года назад

Thanks 🙏🏻

@joepaul1763 Год назад

Just got this kit. I am so intimidated to try it myself

@Its_about_that_time Год назад

Yea me too. These videos make it look so easy since they have a lift. Us diyers need to put the truck on jack stands

@squealingreels2503 2 месяца назад

Just did it on my 2019 with jackstands and a bottle jack. It's no harder than the video makes it out to be. It just takes time and patience.

@NiteSpecial 3 года назад

Would you be able to use the front struts for a Tacoma pre 2005? I have a 99 Tacoma but rough country doesn’t sell front 3in lifted struts for any Tacoma pre 2005.

@DRUMZ4LIFE82 3 года назад

I have the same lift and 285/70/17 is the biggest tire you can run without rubbing. These 33/12.50’s look good but will cause issues. This kit will require a 1” diff drop and upper control arms for caster adjustment and the drivers side needle bearing will need to be replaced. I’m sure you noticed the grinding noise from 20-45 mph. Great kit for the $ but realize there is much more involved so beware! Oh and CV boots rub together and will rip over time. Recommend the boot slide mod as well

@jackdavignon3889 3 года назад

Just purchased this kit, why replace needle bearing on the drivers side? And what’s a boot slide mod?

@DRUMZ4LIFE82 3 года назад

@@jackdavignon3889 the drivers side needle bearing will make a cylindrical grinding noise after the lift, it’s just the cv angle putting pressure on it. Some get lucky and don’t have an issue, I didn’t. Just order the ECGS clamshell bushing, (google it). The boot slide mod is where you take the cv boot clamp off on the inner boots and slide it down the shaft so the ribs don’t touch and reclamp them. Sounds scary but not a big deal really. Check out Tacoma World forum and read up a bit. The kit is good just needs a few aftermarket adjustment. Good luck!

@FivexxXxx5 3 года назад

I have the RC 3.5’ lift and with UCA’s never had any grinding noise. I take it to expert offroad shops . Zero rubbing or trimming

@DRUMZ4LIFE82 3 года назад

@@FivexxXxx5 you got lucky then on the needle bearing

@FivexxXxx5 3 года назад

@@DRUMZ4LIFE82 Idk maybe the guys just know what they’re doing. Because i sure don’t 😅😂

@jc8804 3 года назад

Any rubbing or trimming required to fit those 33x12.5 tires?

@osubigrob Год назад

would you be able to tell me how much trimming you had to do to keep from scrubbing front and rear. RC says for a 285 70 17 with a -12 offset I would have to?? Thanks in advance.

@anhoantoniotaylor2288 Год назад

if I want to put 285/70/16 wheels and tire do I need to change the gear ratio of the diffs? if that the case, what will be the best gpm/gear for a 3th gen 4cyl daily driver/commuter, occasional light off-road taco?, thank you!

@byronsequeira7483 3 года назад

With this kit do I need driveshaft spacer ?

@albinoleon562 Год назад

what's up friend me I have a Toyota Tacoma and I also want to put that same three-inch lift kit on it, I also have to put the specer that you put on it. Ayi, below the washers