Training to use DSN-VC288 Digit Voltmeter Ammeter?

Подписаться 2,4 тыс.

Просмотров 71 тыс.

50% 1

How do you use DC 0-100V 10A DSN-VC288 Voltmeter-Ammeter Blue + Red? for beginners step by step? along with a digital multimeter and using 2 12 and 24 volt adapters and using a fan to show ampere consumption
--------------------------
In this video, I measure voltage and amps separately. I use 12 and 24 V adapters to measure the voltage. I use a fan to measure the ampere. I use a multimeter for comparison.
I will show you the correct way to connect the wires.
--------------------------
my Tools:
DC 0-100V 10A Voltmeter Ammeter: bit.ly/3uCE178
DT9205 multimeter: bit.ly/3HomdEb
24V 2A Power Supply Adapter: bit.ly/3Pjfyx8
12V 5A Power Supply Adapter: bit.ly/3W7HuGt
fan 4*4mm 12V: bit.ly/3Yb456J
------------------------------
Voltage Amperage Power Energy Meter / Tester Voltmeter Ammeter Watt Meter
▬ Social Media ▬▬▬▬▬▬▬▬▬
❤️❤️ If you liked this video, please like this video and follow our channel.
☑️☑️Also support us by sharing the video
📢 Subscribe Channel: / @newtecpro
Twitter: / newtecpro
Instagram: / newtecpro
Email: newtecprof@gmail.com
Telegram: t.me/newtecpro

Опубликовано:

10 дек 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@gasSpring888vn Год назад

thank you so much

@newtecpro Год назад

thnx bro

@mongneverdied1 8 месяцев назад

Thanks

@newtecpro 8 месяцев назад

Welcome my frind

@Flatron888 Год назад

Quick question. What happens if i try to read 105volts with it.... i have a power supply that can deliver little more over 100 and i dont want to burn the module. Will it burn if i exceed the 100v? or it wont show anything more than that 100 stucked in there.

@newtecpro Год назад

Yes, most likely higher than 100 volts will cause damage. Never use more than 100 volts

@Panda-in9zm Год назад

thnks

@newtecpro Год назад

TNx u

@hugodavid2244 Год назад

I just bought two of those meters, I connected them the same as you, but, although it shows the use of voltage and the circuit works without problems, the meter does not measure the current, it is simply at 0, both meters behave the same.

@newtecpro Год назад

Most likely, you have not connected the wires correctly. Please check the wiring method carefully Also, the electrical device must be turned on and consume electricity.

@hugodavid2244 Год назад

@@newtecpro The problem was that they ripped me off, it doesn't even have the metal bar that is used as a resistor to measure current.

@georgioszotos5519 Год назад

@@hugodavid2244 Yours must be V2.0 Without a wire shunt. But on the other side of the A connector there must be an SMD shunt resistor R010. And is brighter as normal SMD resistors. So is my. It works but i haven't used for more than 2 Ampere.

@dinamics2 11 месяцев назад

When i connect shunt ampre readind going to zero, why?

@newtecpro 11 месяцев назад

You may have connected incorrectly. The shunt must be installed in parallel

@dinamics2 11 месяцев назад

@@newtecpro yes its parallel connected.

@sehajpalsingh1223 Год назад

What is cost of this meter

@newtecpro Год назад

Its price in online stores is approximately US $3.73

@JavedKhan-qh3en Год назад

20 HP 3 phase motor ke liye chahie

@newtecpro Год назад

@ratkooporonty Год назад

The reality is that the old (analog) instruments could be used as long as no overcurrent was introduced by mistake, so they were good for many, many years. Today's (digital) instruments don't last more than a year or two, and they break down if they happen to be near the high voltage of an old TV. Some of them are already defective, so today's technology is not user friendly, but hazardous waste friendly.

@__-hh3gt Год назад

You are correct. Thanks

@mohammadpour.61 Год назад

سلام خسته نباشید ممنون مهندس یک توضیح کامل میخواستم دررابطه باطریقه فعال کردن آمپر من یک رسیورمینی دارم که دوازده ولت دوآمپره که ازطریق ماژول افزاینده وپاوربانک میخوام به رسیور برق برسونم اندازه گیری ولتاژوروکه بلدم ولی چطور آمپرو وصل کنم یاانتقال بدم به رسیور ومطمئن باشم که دوآمپر برق مصرف میکنه منظورم اینه دوسیم روبکجای رسیور وصل کنم ممنونم اگه یکم راهنمایی بکنید متشکرم موفق وپیروز باشید❤❤❤

@newtecpro Год назад

The amperage is nothing to worry about. In the technology of switching power sources, the electronic device consumes as many amps as needed. If your receiver uses 2 amps, it will only receive 2 amps.

@mohammadpour.61 Год назад

@@newtecpro thanks❤❤❤