Troubleshooting Canister Rug Nozzle- no power-part one 

You solved my problem today. The wand isn't transmitting the electricity to the brush. Now that I know where the problem is, I fixed it today!

Your suggestion of removing the wand and connecting directly to the rug brush helped us figure out our Electrolux problem. Thank you.

I have a Filter Queen and you just showed me on this video helped me figure out what is wrong with my filter queen beater bar. You Are absolutely amazing, Sir. I can not tell you much I appreciate you. You describe the fix Clearly and thoroughly with easy to understand directions. I’m a 70 year old female and you helped me figure this out. Thank you so much.My problem is in the wand.My husband an electrician and when he gets home from work I’m going to have him test the power on the two cords.Thank you 😊

Hey man, thanks for all these videos. You’ve really helped a lot of people out, hope you’re doing well!

Monroe you're the man!!! I have the Kenmore 200 and the carpet power attachment stopped working. After checking out your video I checked the continunity between the attachments. I started lower and worked my way up to the wand, where the switch to the carpet is. One of the two wires to the switch came out of the connections. After inspecting the wire it appears that the wire connector wasn't even crimped to the wire connector and the insulation wasn't even stripped away to make a hard contact. I stripped the end of the wire reconnected the wire and put it back together. Works perfect! Thanks for the help!!

Thank you SO much. Our local Sears has closed, and your video showed me exactly what's happening with my Kenmore! I can get a new wand.

For whatever reason, simply putting the multi-meter prongs into the ends of the handle fixed the problem. I would not have thought of that. Thanks!😀

Wow this was very helpful. Wish I watched this before buying a new motor and spending hours banging my head against the wall, ha! My issue was the wand.

thanks for the tips. This helped me sort out what had to be checked. I just had to clean the connections with a bit of sandpaper (older model) and everything works again.

Exact model and exact problem with the wand! Thank you for the concise solution!

You started on the right track with the exact problem I have. But you stopped short in explaining further what if it's not the wand that's the issue. What if the wand is fine and the beater bart just wont go! I cannot connect direct to the Beater bar as you did in the video. So my problem still exists. Good to see you were able to help others though

How do you reassemble the height adjustment mechanism on the Kenmore canister ? The next video please have you camera aimed at your hands where the action you are describing is. Thanks for the videos.

Thanks for the video, this was the issue with my vacuum!

I love Kenmore vacuum cleaners.

Also advise your audience where your business is located so we can find you if needed.

Thank you for your advice. Your video helped me solved the vacuum problem. You get a like from me!

So helpful. Very common sense and I'm embarrassed I didn't think to try. That said, on my Kenmore 200 series, the female power plug on the hose end is narrower than the male plug on the nozzle part. I can't plug it in to eliminate the wand as the issue. Is there a workaround to this? The unit looks virtually new. I'm a reseller, but I'm sort of stuck because I have three parts (hose, wand, and nozzle) and don't know which one is broken. I don't want to sell something I'm not confident in. I think I'm local to you. (Monroe, NC?) Do you have a another 200 series we could interchange parts with?

Thank you today! Success with my issue thanks to you!!!!

Thank you so much that was my vacuum problem

I tried this suggestion as I thought it was a great suggestion. Now the main motor doesn't work either. Looking for a repair shop or a new vacuum to replace this 2018 Elite model. We really liked this model too.

Thanks a lot, that was the problem

Thanks so much for posting this! 😃👍🏽

Awesome video, exactly the info I need 👍👍🌻

Our problem is no power on the motor that sucks. The roller is working and has power. A little different that this video... Curious if you have a video for that motor or curious if you can suggest where to start? The bag was very full and wife didnt realize how full it was.

Thanks. I have a power nozzle issue, so I took out the extension wand out and connected the handle directly to the power nozzle and I have the same issue. My nozzle plug wire came in the mail today so I will try to put it in. Hoping that solves the issue and the problem is not in the handle/switch etc.

Hey and I am a new subscriber. Question for you, I have been taking my Kenmore Whispertone Powermate apart and cleaning it inside for years and the last time I did so, the light came on but the power nozzle will not come on. All the electrical inputs and connections seem to be fine so any suggestions for me to check before I order just the reolacement powermate which I found on ebay? My model is a 116 Green Whispertone from the 90's. Thanks much!

Thanks for your expertise! We have a newer model of the vacuum you show in the video; we followed your suggestions and the wand is fine. The problem is the "carpet" function on the switch - very low power. What would you suggest?

before watching this video, I did try to connect it without the wand, but connector wouldn't allow it, so I put a multi-meter and it was giving me 30V is a Kenmore 400 Series Hepa Media Filtration, do you know if that's the correct voltage that is supposed to give out?

Has hoping you would take apart head to at let's see how it's done. I'm fearful of snapping clips or trying to disassembly in wrong order.

Do you have any video on kenmore canister 400 disassembly cant get the bad separated there are no more screws

can you do a zoom consult to tell me if my Kenmore brush roller needs to be replaced? it looks fried and smelled like it was burning when the roller wouldn't turn.

Thank you!! it was the wand!!

Darn I thought this would help. I connected the nozzle to the power brush and nothing. Could it be the switch on the handle, maybe?

My 700 series lost power totally after suckong up a sock and unattatching the hose the terminal peice broke and I replaced it still not working :/

My Miele canister is bot getting power to the nozzle. I have ruled out the wand, hose and power head. As I have 2 vacuums. Could it be the part were the hose connects into the canister. I believe its called a socket. Thanks

Thank you, if you are local i would like to bring my vacuum cleaner. I did what you said and still not working

thanks - but note - that my kenmore canister handle will not directly attached to the powermate to check if it's the wand is the issue - will not fit down enough to engage the elec connections ?

I have a Sears Kenmore and I cannot bypass the wand because the connection is different from the handle to the powerhead. Any ideas how I can test it?

I wanted to know how to reset the beater bar. You didn't touch on that.

Thanks for the video. Have Kenmore 600 series that the power nozzle is not working. Checked continuity of the wand with multimeter. What I found is that I have continuity with the wires, but it appears that the same side connector has no continuity. However, continuity with wire to the opposite side. Is it possible Kenmore purposely crosses the wire for some reason? Also, as per your video, I cannot get the handle to fit directly onto power nozzle. Any help and opinion would be appreciated.

I have the exact model and it is doing the exact same thing. when I tried what you said . I still cut off and on so it wasn't the wand . When I move the wire around the base it goes on and off. How would I repair that

Hi. Why is it that my canister shuts off sometimes when I pull the electric cord out of the canister or when I roll it in. Please help.

Was told the motor probably burnt out, but inspection and the nose knows it didn't. Just wasn't getting power because in the handle there were two pulled crimp connectors trying to connect the solid wires in the hose to the braided on the selector switch. Hose must have turned. Not impressed with the over engineering, when it comes to opening to gain access to the belts, etc.

I almost thought I had found the problem when I saw this video… but I didn’t 😢. The carpet attachment cuts off and on as I manipulate the wand (wish I could attach a video of it doing this)… frustrating 😢. I’m sure the problem is within the attachment itself…

Just tried the wand removal and the brushes still not moving… any other suggestions please?? Thanks

Problem with ours is the male part on the handle doesn't fit the brush female part