Turbocharged SEE THRU ENGINE on EFI and Nitromethane (FINAL EPISODE)

Подписаться 1,4 млн

Просмотров 657 тыс.

50% 1

In this episode of the see-through engine I attempt to blow the engine up yet again and finish where I left off in episode 7.
I had nothing but sensor pick up problems in episode 7 due to electromagnetic interference from the high spark energy of the ignition coil that I used so I had to cut the episode short.
This is the grand finale of the see-through engine series for See thru engine V.1 and more than likely the last episode with this particular engine, it may make a cameo appearance here and there.
thanks for your support and thanks for watching through the entire series.
this one is a pretty long video so please find the program guide below.
0:05 Intro
0:43 Changes I Made
1:58 1st Test Run
3:41 Not Starting
5:23 2nd Start Attempt on the new setup
6:25 1st blow-up Attempt (gas)
10:20 2nd Blow-up Attempt (gas)
13:45 3rd Blow-up Attempt (Nitro)
14:54 4th Blow-up attempt (Nitro)
See Thru Engine Series Playlist: • See Through Engines
↓↓All Previous Episodes↓↓
E.1 • See Through Engine - 4...
E.2 • See Thru Engine Runs T...
E.3 • See Through Engine (S1...
E.4 • See Through Engine on ...
E.5 • See Thru Engine on Tur...
E.6 • See Thru Engine on New...
E.7 • See Through Engine on ...
Big thanks to Briggs & Stratton: www.briggsandstratton.com
and DIY auto tune AMP EFI: www.diyautotune.com
↓↓Social media Links↓↓
🐦 ► Twitter: / warpperception
👍 ► Facebook: / warpperception
◙ ► Instagram: / warped.perception
☢ ► IMDB: www.imdb.com/title/tt5548028/?
I sometimes post things early or post previews on FB and Instagram so if you like that sort of thing give them a visit.
Please leave any opinions suggestions or comments Below and don't forget to check out our other videos and subscribe, Thank you.
Watch this in 4k when possible, it looks incredibly awesome !
Written and Directed by: Matt Mikka
Carbon 12
www.c12.tv
Produced By: Carbon 12
Directed By: Matt Mikka

Развлечения

Опубликовано:

1 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 829

@NewMind 4 года назад

What an incredible series! Really enjoyed how you intuitively and visually connected reality with the mounds of theory. Great job!

@WarpedPerception 4 года назад

Thank you! BTW I'm going to send you a viewer request very soon.

@thegadgetbuilder4268 4 года назад

The slow motion filming was amazing. I just used the same type engine for a similar but different project which I just put on youtube.

@nikkiarcand4135 3 года назад

@@WarpedPerception it would be cool to see it run on methanol. It's a cooler running fuel might get some longevity.. maybe ?

@larry800s 3 года назад

Cornal Angus snl

@richardwhitaker4148 3 года назад

Should've of raffled off the heads that went bad.

@ProjectFarm 4 года назад

Those Briggs & Stratton engines are nearly indestructible! Great job and definitely the BEST production quality on RU-vid!!

@WarpedPerception 4 года назад

Thanks, I got to get one of those predator engines in my hands soon !!! Lbvs

@cutthroat399 4 года назад

Two of my favorite RU-vidrs know each other. You guys show make a crossover video!

@backwoodsjunkie08 4 года назад

I always loved to race Briggs 5hp at the kart track! I knew some guys in the unlimited class that we're getting 18hp out of the blocks! Lol the only stock part of the engine was the block... And even then "stock" was a pretty subjective term

@TheCelltek 4 года назад

Just like a TIMEX, "It takes a licken and keeps right on a tickin"

@TheAshlec 4 года назад

Warped Perception would have been nice to put the original head and sparkplug back on to finish off the engine. And see what actually fails not just the plastic head! One more episode??😬

@dishsoap1 4 года назад

I’d like too see a see-thru 2 stroke engine.

@WarpedPerception 4 года назад

It is coming!

@Tuber360904 4 года назад

dishsoap1 damn ask and you shall receive lol

@mr.engineear0987 4 года назад

dishsoap1 good suggestion but 2 stroke wouldn't be as fun as the 4 stroke

@dishsoap1 4 года назад

Mr.engineEAR09 I think seeing the scavenging process in slow-mo would be worth it. I’m glad it is in the works.

@mr.engineear0987 4 года назад

dishsoap1 good point man 👍

@nitro_rc_dude8158 4 года назад

Do a engine teardown. Would be awsome to see the inside of it after all of that.

@WarpedPerception 4 года назад

Ok that's a great idea, I will have to do that on my personal channel. I need to clean it up for my exhibit anyway.

@Fabio.-. 4 года назад

Try using a regular head and see how much power you can get

@AiOinc1 4 года назад

He did that last episode

@idahoshoter 4 года назад

He did 11 torq and like 13 hp

@WarpedPerception 4 года назад

Here you go ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-9hMnlyKZLwE.html

@schuchdan02 4 года назад

You should have added nitrous oxide if you really wanted to blow it up good!!

@kd7cwg 3 года назад

@@schuchdan02 did that to a push mower years ago. It survived 🤣

@deleterium 4 года назад

8:08 With high speed camera and transparent air intake you can adjust optimal timing for fuel injection! Note that it was not injecting at the same time the air flows into cylinder.

@WarpedPerception 4 года назад

You're right it was not, because the sensor is already shot so the ECU is just taking a guess at the RPM at this point

@michaelpressman7203 Год назад

It ran

@dylanyates6331 4 года назад

I think the best part about this is the problems you ran into are legitimate problems the automotive industry ran into when they started. Really getting back to the basics

@michaelpressman7203 Год назад

Difference is budget constraints

@robertschmidt7625 4 года назад

Regardless of size or HP, Briggs & Stratton engines are tough, reliable, and virtually indestructible. This engine however deserves an A+ in quality! Best in the world! #1!

@NitroGuyJH 4 года назад

Been a great run Matt. I’ve watched each episode from the first upload to now and can’t say that I’m not pleased! Great work, awesome videography, ad killer content brother!

@slitherixxx 4 года назад

the dedication and effort put into this.... i salute you

@buder5116 4 года назад

14:21 noticed the spark going through the hole while in the air ? Awesome

@SWXSTXK 3 года назад

respect+ for this dude to stick onto this project for such a long time. absolutely loved this series. binged watched all 8 eps in the whole night. its 5am now. gn!

@metaomicron72 4 года назад

Thank you for this series and more stuff to come! We'll be here to watch it :) You're awesome

@lexus_offroad_adventures 4 года назад

Been waiting for this video! So cool to see boost doing its thing.

@kjell-richardlvdal373 4 года назад

you are the best teacher i ever had, making dry theori into understandable testing in the real world

@Dubz0408 4 года назад

Unless youre ending this series with something spectacular in mind, like a turbo see through rotary, I want to see this with *MOAR BOOOST!!!*

@WarpedPerception 4 года назад

Don't worry, this is coming in the next series, all of that stuff... Very soon.

@Comet-lv3nk 4 года назад

A 50 psi turbo, with a nitrous bottle blowing into it...

@JesusGarcia-ec7jo 4 года назад

The most nostalgic and satisfiying end that i'v see on a serie!

@LouieTheLug 4 года назад

Thank you for all you do.!! I enjoy your videos. They are extremely educational and entertaining. I can’t wait for the next 2.0 or next see thru engine videos to come. ⚙️

@wdtripps6537 4 года назад

Your skills are now to the point of spiritual insight. Awesome series

@jamesadams2333 4 года назад

Thank you for the wonderful series! Keep up the great work. I hope to see more!

@Les__Mack 4 года назад

Fantastic series! Thanks for making these videos, they are awesome!

@fabio77809 4 года назад

cabbage I cry my heart, that this episode is the last of the series of this turbo engine, thank you for your explanations that you gave us about this engine, I do not see now that the second season of the turbo engine is coming out immediately

@backwoodsjunkie08 4 года назад

Love your videos my dude! Keep up the awesome content

@Poshoo 4 года назад

I can't wait to see what the next engine will be! Good video!

@Lozzie74 4 года назад

You impressed me with your resourcefulness. The engine would stop, you would quickly figure out why, easily resolve the problem and have it running again soon after. You made electrodes from bolts! You are MacGuyver!

@g2westwood 4 года назад

no way man , don't give up .... I love this series!

@dhanisvaran5135 4 года назад

Thanks for the all efforts , money spent & hard work... We love it 😍❣️ keep going on...

@Srikrishnakarthik 4 года назад

Thanks man, appriciate all the effort you have put in. I will always remeber the first time I saw HOW IT ALL WORKED. I am an automobile engineer and makes me soo happy seeing this never really knew how it worked practically, it was always theory or prectical but this real time see through , blew my mind. God bless you, wish you and ur family good luck and fourtune.

@NiCadHeliPilot 3 года назад

Ka pai! An epic conclusion to an epic series.

@MoisesQuirozT 3 года назад

Great job megasquirting that small engine man, I can't get enough of your videos, thanks for the effort you put on them.

@tylerstrausser7651 4 года назад

Time to sell it on Craigslist. “Never abused. Rarely used it.” Lol

@sirBumpyCase 3 года назад

I really appreciate your slo-mos and overall production quality!

@WarpedPerception 3 года назад

Thank you

@jacebigelow 4 года назад

I enjoyed this series very much, your persistence and determination is great. Incredible camera & lighting work too !! Cheers !

@WarpedPerception 4 года назад

Thank you.... And on to the next. That's one of the reasons I had to bring it to an end no matter what, gotta move to the next projects which are bigger and better.

@RayJonesXD Год назад

One of my favorite series on youtube I've watched :D Thanks fam

@williamhart4896 4 года назад

Those old Briggs and Stratton engines are tougher than I would've thought

@just_j0e 4 года назад

Kinda sad that you stoped doing this series it helped me at hard times thank you so much for theese videos 😊😊

@bryanroupe8646 4 года назад

This series has been awesome. Deserves a ton of views and likes. You have a wild imagination.

@dubleblitz 3 года назад

One of the coolest things I have ever seen in my life

@daszieher 4 года назад

Excellent series! You normally only get to see this kind of stuff in a lab. Very good piece of entertaining education!

@pw383426 4 года назад

Yo man. Your ingenuity is the reason why I watched EVERY episode of this series. All the fights, struggles, and issues really kind of forced you (and us) how to learn about mechanical engineering. So cool. I hope the next project is just as ridiculous and as home made as this one is.... I'm hoping for a supercharger episode for christmas

@WarpedPerception 4 года назад

Thank you, I also find that to be true and that's why I like doing these episodes this way, as we figure out solutions for unforeseen problems we learn a lot that we didn't expect to about things that we didn't expect

@daniel_poore 2 года назад

Ive been waiting to watch your ignition screw shoot out the top for 8 episodes now! It finally happened!

@willemh3319 3 года назад

real educative i showed your Br and strat to my daughters to show them how an engine works they loved it specially the destructive part of it👍👍👍👍👍

@floridapielady 3 года назад

The entire season I was freaking out. Not over the anticipation of the engine exploding; that had me on the edge of my seat in excitement! I was freaking over that $140,000+ dollar Phantom Flex 4k high speed camera setup you were using. It was so close to the engine I thought any minute kaboom and the camera would be toast or covered in oil, etc. Seeing that would be the equivalent to witnessing a wreck of an exotic or rare antique car. I hope it's insured! 😉

@sepehrmovahedijalali3054 4 года назад

Awesome Series. That was a mixture of theory and action I really love it.

@WarpedPerception 4 года назад

Thank you !!

@MrRolandeid 4 года назад

Awesome job, stuck watching the whole episodes, i was excited to see how this engine evolved, i thought we might see it on a plane 😂

@radekciskowski2070 4 года назад

The amount of work, time, knowledge and skills you've put into this thing and all this just to show it in this episode is incredible! The next episode should be to make it run on diesel - that would be quite challenging... but you wouldn't need that stupid spark! :D

@max_power8510 4 года назад

Your determination is admirable. I like how you kept trying and trying. It was very awesome to watch. Only thing I can think of is to use a nut on the bottom side so you could thread a regular spark plug through the top, but it would require more work. Like I said, excellent video and thanks for pushing all the way through.

@user-hq4ly7xu5m 4 года назад

That so beautiful burn !

@FgMar-eh7xd 3 года назад

You are a crazy man, I like to see the engine make the explosion, nice video

@CoolayyyPlayz 2 года назад

2:07 omg the engine sounds so good and so smooth. sounds like a four wheeler engine at this point.

@davyarthurs 4 года назад

In the slow-mo you can see that the ECU runs a waste spark system. Been a nice series this one. Can see some serious work and effort has gone into it!

@nonstopsaurier 4 года назад

Amazing Series!

@lesslisilverman 4 года назад

Briggs and Stratton should be making car engines.

@keithy4129 4 года назад

The engines on most modern day cars are incredibly reliable. It’s all of the electronics that are the problem, this Briggs engine is a tank because it’s is very simple.

@redneckasmr-xd1gg 4 года назад

we can thank the epa they wont let car manufactures use the flat head design anymore because it is not efficient enough for them

@Eduardo_Espinoza 4 года назад

flat head designed engines died out in the 40's or 50's for cars the reason lawn mowers still use them is because they don't need a lot of power and it's a lot cheaper

@CustomcrowdMitroc 4 года назад

Toyota landcruiser is pretty much a b&s engine they are just as reliable

@djaydeved 4 года назад

yeah they could make something beter than a 2jz or any famous engine that is known for being able to take a 1000 shot of nitros oxide (nos)

@wesb9546 3 года назад

This entire series is so brilliant. It reminds me of a drunken idea i'd have with a friend and then never follow upon...good job on not only doing this series, but doing it really well. Excellent execution, amazing production, ect. Well done sir!

@WarpedPerception 3 года назад

Thank you, that's also how I feel at times, like it's some drunken idea!! Lol

@wesb9546 3 года назад

@@WarpedPerception and you respond to comments! next level dude.....hey as a follow up, what's your background? just wondering where you got all these highly developed tinkering skills...

@sampence1928 3 года назад

The wood screw bouncing around the table near the flywheel reminds me of final destination. Lol

@SpaceShipDeathstar 4 года назад

I never knew that a simple bolt was acceptable as spark plug. Amazing content!

@shipshrekt2156 3 года назад

It’s not lol

@-DarkKnight- 4 года назад

I like that you do a "Loudness Warning". I'm always using ear buds, so when it gets loud, talk about pop an ear drum lol.

@WarpedPerception 4 года назад

Thank you, yeah I started doing that because previously I used to turn the volume way down, but then people complained that they couldn't hear the sound of the engine, but then if you're wearing earbuds it's a completely different story..lol like you said pop an eardrum!

@koenjanssen81 4 года назад

So now I can't wait for the second series to start. It's like a series on Netflix 🤣

@WarpedPerception 4 года назад

Lol... Thanks, I never knew people would like these so much.

@koenjanssen81 4 года назад

@@WarpedPerception it's awesome to see. As I don't have the funds and time and let's not forget knowledge to do this I really enjoy whatching these videos

@mastershefu147 4 года назад

Netflix for men

@koenjanssen81 4 года назад

@@mastershefu147 hahaha true story

@djaydeved 4 года назад

@@WarpedPerception ay i got an semi old predator 212, though postage would be more expensive than you just buying one straight from the usal suspects. (harbor freight special)

@abazzi910 4 года назад

Nice videos, man! I love the content!

@ThinkCleverAndSmart 4 года назад

Wow, this is good PR for Briggs & Stratton. Also, loved the montage at the end! :)

@peabow1031 4 года назад

Thanks I enjoyed the journey.

@MrAjam12 4 года назад

You should put that setup on a go-kart with the turbo and EFI.

@drakethesnake1000 4 года назад

This is sooo cool... Thanks Man

@neoplasmax 4 года назад

You were saying "something cool has to happen" in attempt to try and blow it but I have been thinking something cool already has happened.. It can survive a turbo and nitro! Now I'm heading to store to get a setup and put this on my go-cart!

@austinkreller7592 4 года назад

I loved the series man keep it up! To help the ECU receive proper input make sure you have a ground probe spaced .035 away from the spark lead, gives it a place for the spark to jump to and a proper ground. Not having a ground to the coil will cause all sorts of issues within the ignition system

@abelferquiza1627 4 года назад

Your work should be seen and studied un every mechanics or engineering school, college and universities. Thanks for sharing with mortals!

@wesleybuck5725 3 года назад

Brilliant Series! A way to get around the turbo not wanting to boost more is to use nitrous to spool the turbo or just using nitrous without the turbo. Should be able to inject enough nitrous to cause the engine to blow without much effort. A come back with nitrous would make a brilliant episode...

@AdriqueGames 3 года назад

This guy deserve more subs!

@xxxftcxxx 4 года назад

Send that drill to AvE and let him take it apart!!

@marktucker208 3 года назад

You are a clever guy, incredible

@boltonky 4 года назад

Great video and i do like how in depth you go without getting over the top....only problem i had with whole thing is the injector not being aimed downstream so fuel keep atomised

@qforrest7294 4 года назад

Great video!

4 года назад

I watching you from Turkey. You are very professional

@WarpedPerception 4 года назад

Thank you !

@oneal43 3 года назад

Sitting here at 12:50 at night wondering 1: Why am I not asleep, and 2: Where did I go wrong with life.

@wildefox1478 4 года назад

Pretty awesome, too bad it didn't blow up but that just shows how indestructible Briggs engines are! Looking forward to the new series!

@PhantomHighSpeed 4 года назад

Oh Matt, the music near the end. Good by see-through engine. You were a good friend!

@natequillin4365 3 года назад

New subscriber here. You are on to some seriously interesting stuff man, nice work

@natequillin4365 3 года назад

Also, how to you avoid carbon monoxide poisoning?

@AtlasReburdened 4 года назад

Awesome video.

@a1sloth1 3 года назад

EXCELLENT TEACHING TOOL!

@ColdSmokes 4 года назад

The see-through head was certainly cool and all and quite a bit can be learned about the combustion process but it was ultimately the Achilles heel of the main objective to blow it up. The head was going to fail every time before any hard parts would or could.

@jerrypizzini 2 года назад

This was cool to see.

@vancemacd6315 4 года назад

I would put this in my car and probably race most the Hondas around my area. Great series,

@login866 4 года назад

i got a suggestion, why not use compressed air from a compressor to charge the engine since the turbo is not making much boost. usually a engine internal can take way more then 5 psi

@kenbirkin7753 Год назад

great series , and thumbs up to brigs straten, i have punished Honda GRX in normal operations but many makes would have broken

@paulodaxx 4 года назад

wow! Great video! Thanks!!!!!

@1071Halil1453 4 года назад

Perfect test thanks bro

@FRANK1092 4 года назад

hello Man, thank's very much for the content, was amazing. gad bless you.

@americanlivesmatter-BmanWild 3 года назад

The slow motion cam and the music chosen is a really good touch ..well done bro!

@upsidedowndog1256 4 года назад

I might have gone for broke with the iron head, but you did a great job with this series. I look forward to more of your videos on all of your channels.

@WarpedPerception 4 года назад

Thank you!

@michaeldemetriou1399 Год назад

That is a great creation

@ssj3mohan 4 года назад

vert fun to watch.

@RistaMotorista 4 года назад

too bad this series is over maybe use honda engine for next series? or a see thru rotary engine, wich is my personal favourite

@scenicdepictionsofchicagolife 4 года назад

Haha he actually has a see thru rotary series already!!! Go check it out!

@WarpedPerception 4 года назад

@@scenicdepictionsofchicagolife yes and I'm currently working on the second version of that rotary engine which was initially supposed to be the first episode but I ended up going with the simpler smaller design instead so everyone can understand.

@vincentrobinette1507 4 года назад

It would be difficult, to build an overhead valve cylinder head out of plexiglass. Valve seats, and the exhaust valve guide just get too hot!

@scenicdepictionsofchicagolife 4 года назад

@@WarpedPerception that's cool dude. Wish I could check your shop out 😂 I live in Chicago too by Portage Park

@jameshunt2141 4 года назад

i see a briggs .. i see a turbo, you just got a new subscriber!

@sinewave3323 4 года назад

Awesome bro! Gd to see ya again! I wish you and you're family a happy new year! And a merry christmas! Ik its early lol! But just incase! 😎👍🏻👍🏻

@andremeyer1449 4 года назад

Thanks...sometimes you have to stop when it's best 😍

@zdrehsbuckland488 4 года назад

I think your main issue is the length of spark gap which is allowing the voltage to spike much higher than intended which in turn creates large electromagnetic interference spikes - these will induce current spikes in any nearby wiring or sensors. The fix is to shorten the spark gap back to same as speced for standard spark plug, maybe add an extra grounded bolt at an angle which will make the spark gap adjustable

@chaosminecraft3399 4 года назад

Nice engine. It is not destructive with the clear head. Nice. 😉👌

@mohammedabenourseddiki6860 4 года назад

Thanks for the sound warning it saved me from earrapes

@CustomcrowdMitroc 4 года назад

I wouldn’t mind seeing him deject a air compressor into the intake of the turbo just to really get it spooling and put the original head on. The see thru head is what’s causing the issues