Tutorial: Setup single infra red beam sensor (AGO-20 IP55)

Подписаться 1,6 тыс.

Просмотров 86 тыс.

50% 1

In this video you can watch how to do the wiring on AGO-20 IR beam sensor and connect it to DC lighting or DC alarm (buzzer).
Klik link below to get your IR beam sensor... Toko T4Murah di tokopedia:
tokopedia.link/uMKDEcp5j8
#AGO20
#singleinfraredbeamsensor
#DIY
#IP5
#infraredsensor
#T4Murah
#tokopedia

Опубликовано:

21 июл 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 53

@burnsdownunder Год назад

Thanks for the wiring guide. it worked perfectly.

@recargable2 3 года назад

Thanks good tutorial. i was confused what to do. but now I know.. I thought it was easier.

@satria155 3 года назад

You're welcome...

@eight8547 Год назад

Thanks your the man 🎉🎉🎉🎉

@lenertburnett1079 Год назад

What size wire would you recommend for the connection?

@abn2684 2 года назад

What gauge wire is used?

@billybodine4541 27 дней назад

Will this work with a 5 volt power supply?

@JustinMathewVettickattil 2 года назад

Hi! Great video. Can we connect a 30W water pump with the beam sensor?

@satria155 2 года назад

I have not tried such thing, sorry

@beebwarobert4055 Год назад

Nice work, but could you share the wiring diagram

@Bakwas.gaming Год назад

Good information but if enyone cross the line buzzer ring 2 or 3 secong not continuous pleace tell me how buzzer ring continuous even enyone cross i hope you understand me

@blackbunny3880 4 месяца назад

isn't autonomous is for installed thru alarm equipment

@rizalmaulana6279 3 года назад

Bang, tolong bikin video tutorial install single photo beam pada automatic sliding gate.

@satria155 3 года назад

Maap baru reply... Rumah gw ga pake pager bro... 😅

@058Jacko 2 года назад

If you powered by an a23 battery, how long would the battery last?

@satria155 2 года назад

Sorry i haven't tried it

@jarnailsingh7074 2 года назад

plzzz tell me connection of photo cell in boom barier

@satria155 2 года назад

Which one?

@stuartlaw3575 3 года назад

The drawing and exploration that comes with these components ,is totally different from this video the translation is totally rubbish ,so quite pleased when i found this video ,I wired it step by by step and had a friend check it out after to see if correct .IT STILL DID NOT WORK ,Sent off for another set THAT DID NOT WORK EITHER ?

@satria155 3 года назад

Yes, you are right. When i followed the instruction manual from the box, the unit is not working. After several research on RU-vid/ Google, i found that this is how the unit works. Please consider the jumper selection, Normally Open or Normally Close. I hope you can find a solution for your problem soon. Goodluck!

@ezmoney6753 3 года назад

Would it work on a sliding gate?

@satria155 3 года назад

Do you mean using the sensor to open/ close sliding door? I haven't tried such thing. As long as you can link the sensor to the motor switch, it's possible.

@abrahamgonzales1101 2 года назад

any update about your sliding gate Sir? want to do it

@JustinMathewVettickattil 2 года назад

@@satria155 Can we connect a 30W water pump with the beam sensor?

@satria155 2 года назад

@@JustinMathewVettickattil i have not tried it. Sorry...

@prasetyomargoutomo8087 3 года назад

Bsng kenapa itu port 3(com) di couple sama port 2?

@satria155 3 года назад

Biar sirkuitnya nutup bro...

@melalakyuk2104 9 месяцев назад

Biar ga mati2 suaranya gmn

@ahmadsanufat-cpoetrapoeser9739 3 года назад

Slamat pg om.. mau tnya.. kalo pny sy jika COM saya psg kabel plus trs kita halangi snsor nya, kok cetak cetek mulu knp y? , jadi.. ky bocor rilay ny.. hrus ny kan ga mslh ya?. Jika CoM it brmuatan arus volt?. Tp bila ga di pasangi kabel normal.. gk cetak cetek. Kira kira ap ny y om?.. mhn bntuan nya.. trimakasih..

@satria155 3 года назад

Maaf om saya tidak paham maksud pertanyaan....

@normanadhitya9585 2 года назад

Com jumper negatif

@BoyBoy-ps1fd 6 дней назад

Bang mau tanya harus pakai cable untuk nyala nya ?

@satria155 6 дней назад

@@BoyBoy-ps1fd iya buat ke power source nya

@siswantodm5122 3 года назад

Sampek brp meter jaraknya pak?

@satria155 3 года назад

Technical Parameters : Detector Area : indoor 20m. Outdoor 10m work voltage : 12V,24V Work current : 50MA temperature : +50~ (-30) Size : 49.2 x 76 x 21.6MM Water Proof, UV proof

@jiewsgarage 3 года назад

Bang mau tanya..Di posisi NO..bisa ga alarm tetep bunyi saat sensor tersambung kembali..

@satria155 3 года назад

Kalau mau tetep bunyi harus pake modul alarm sepertinya, pernah liat yg bahas di youtube, tp saya lupa link nya.

@juanalbertoalegriavasquez8697 2 года назад

@@satria155 Hola desde Santiago de Chile, para que la alarma continúe sonando, debes agregar dos dispositivos mas, 1) Un Relay de 4 Pines (85-86 y 30-87) de 12 Volts 40 Amperios y un interruptor o botón de encendido apagado, así al pasar por el sensor activa la alarma y seguirá sonando hasta que le cortes el suministro con el interruptor, luego conecta la corriente nuevamente para activar el sistema, es relativamente fácil la construcción del sistema, incluso le puedes agregar una baliza rojo o azul al mismo Relay.

@satria155 2 года назад

@@juanalbertoalegriavasquez8697 Thank you for the explanation. I'm translating it into Indonesia Language: Halo dari Santiago de Chile, agar alarm terus berbunyi, Anda harus menambahkan dua perangkat lagi, 1) Relay 4 Pin (85-86 dan 30-87) 12 Volt 40 Amps dan sakelar atau tombol on off, seperti melewati sensor ini mengaktifkan alarm dan akan terus berbunyi sampai Anda memotong pasokan dengan sakelar, kemudian sambungkan lagi arus untuk mengaktifkan sistem, konstruksi sistemnya relatif mudah, Anda bahkan dapat menambahkan warna merah atau biru suar untuk itu Relay.